eta Gustus 4128 Kitchen Machine User Manual

Gustus 4128 Kitchen Machine

Kitchen maschine • USER MANUAL

Product images are for illustrative purposes only

eta 4128 GUSTUS

USER‘S MANUAL
Dear customer, thank you for purchasing our product. Please read the operating instructions
carefully before putting the appliance into operation and keep these instructions including
the warranty, the receipt and, if possible, the box with the internal packing.

I. SAFETY NOTICE

• Consider the instructions in the user‘s manual as a part of the appliance and provide
  it to other users of the appliance.

• Check that the voltage on the type label corresponds to the voltage in your electric power
  socket.

• This appliance shall not be used by children. Keep the appliance and
  its power cord away from children. Children shall not play with the
  appliance.

• Appliances can be used by persons with reduced physical, sensory
  or mental capabilities or lack of experience and knowledge if they
  have been given supervision or instruction concerning use of the
  appliance in a safe way and if they understand the hazards involved.

• If the power cord of the appliance is corrupted, it has to be replaced,
  by the manufacturer, its service technician or a similarly qualified
  person so as to prevent dangerous situations.

• Before exchanging any accessories or accessible parts that are
  moving during use, before assembly and disassembly, before
  cleaning and maintenance or after finishing the work, switch off the
  appliance and disconnect it from mains by unplugging the power
  cord plug from the electrical socket!

• Always unplug the appliance from power supply if you leave
  it unattended and before assembly, disassembly or cleaning.

• Never use the appliance if the power cord or power plug are
  damaged, if the appliance is not correctly operating or if it has fallen
  on the floor and been damaged, or if it has fallen into water. In such
  cases take the appliance to a professional service centre to verify its
  safety and correct function.

• When handling the appliance, especially during installation of any
  accessories, removing food from containers and cleaning, please
  proceed carefully – the accessories are sharp. Injury is imminent
  if the appliance is used contrary to the operation manual.

• Do not insert the power plug into the electric power socket and do not pull it out
  of the electric power socket with wet hands or by pulling on the power cord!

• When the appliance is in operation, prevent pets, plants or insects to get in contact with it.

• Do not plug the power cord in the electrical socket and do not unplug it with wet hands
  or by pulling the power cord!

• The appliance is intended for home use and for similar purposes (in shops, offices and
  similar sites, in hotels, motels and other residential premises, or in facilities providing bed
  and breakfast service). It is not intended for commercial use!

• Watch the appliance for the entire time of food processing!

• Do not place any objects on the top of the appliance.

• Only use the appliance in the working position at places with no risk of overturning and
  in a sufficient distance from other objects (such as curtains, drapes, etc.), heat sources
  (e.g. fireplace, heater, stove, cooker, radiators, hot air ovens, grills) and wet surfaces
  (e. g. sinks, wash basins).

• This appliance is not intended for outdoor use.

• The appliance must not be used in a damp or wet environment and in any environment
  with the danger of fire or explosion (premises where chemicals, fuels, oils, gases, paints
  and other flammable or volatile materials are stored).

• Never immerse the drive unit (or any part of it) in water!

• Before preparation, remove possible packages from food (e.g. paper, a PE bag, etc.).

• Do not turn on the appliance without any ingredients inside!

• Always use only one function of the appliance, never turn on several functions at the
  same time (e.g. processing food in the bowl B1 and at the same time in the blender F).

• Do not exceed the maximum time of uninterrupted operation – see the table.
  Never exceed the total time of 30 minutes of uninterrupted operation. Then let the food
  processor cool down for at least 30 minutes.

• Before connecting the appliance to the mains, make sure it is turned off.

• Do not use safety lock controlled by the blender cover A8 for switching off the appliance!

• Your foot processor is fitted with an electronic speed sensor control that is designed
  to maintain the speed under different load conditions. You may therefore hear some
  variation in speed during the operation as the foot processor adjusts to the load and
  speed selected – this is normal.

• The appliance is equipped with thermal safety fuse which disconnects current supply
  incase of engine overloading. If it occurs, unplug the appliance and let the appliance get
  cooled.

• For safety reasons, it is not possible to exchange the attachments while the drive unit
  is in operation.

• Containers are not intended for storing and storing food. After processing, place the food
  in another container suitable for storage.

• If the processed foods stick to the accessories (e.g. whisks, kneading hooks, blender
  blades), or container, turn off the appliance and clean the accessories carefully with
  a spatula.

• Do not insert accessories into any body cavities.

• When assembling accessories, carefully follow the instructions for use. Any other
  assembly combinations are not permissible, otherwise the appliance shall not properly
  work!

• Before removing accessories from the drive unit, allow the rotating parts to stop
  completely.

• When mounting or removing the bowl, do not apply much pressure on the bowl handle.

• Do not lift and carry the food processor using the bowl handle, but always use the
  recesses at the bottom of the drive unit!

• Prevent your hair, clothing and accessories from getting too close to the rotating parts
  to prevent catching and winding them!

• Should excessive vibration occur when using this attachment, either reduce the speed
  or stop the machine and remove some of the contents.

• ATTENTION: Do not use this processor in series with an external timer, remote controller
  or any other device that switches on the appliance automatically, since a fire risk exists
  when the processor is accidentally covered or displaced at the moment it switches on.

• Make sure that the power cord does not come into contact with the rotating part of the
  appliance.

• The power cord must not be damaged by sharp or hot objects, by an open flame and
  it must not be submerged under water.

• Never place it on hot surfaces and do not leave it hanging over the edge of a table
  or a work bench. If the cord is brushed against or pulled by for example children the
  appliance may tip over or be pulled down and lead to serious injuries!

• If the use of an extension cord is necessary, then it must not be damaged and must meet
  the valid norms in force.

• Only use the appliance with original accessories from the manufacturer.

• Use this appliance only for the purpose for which it was designed as specified in this
  user‘s manual. Never use the appliance for any other purpose.

• WARNING: There is a risk of injury in case of incorrect use (not in accordance with
  the manual) of the appliance.

• All text in other languages and pictures shown on the packaging, or the product itself,
  are translated and explained at the end of this language mutation.

• The manufacturer takes no responsibility for damages and injuries caused by the
  incorrect use of supplementary machines and accessories (e.g. ruining of foods, injury,
  cuts) and takes no responsibility arising from the warranty on the appliance in the case
  that the above safety notices were not followed.

Notice!
An integral part of this manual is also a table with the contents of the robot TAB
package and instructions for accessories AC .

II. PREPARATION AND USE

First remove all packaging materials, take out the food processor and all accessories.
Then remove all adhesive foils, stickers and paper from the food processor and
accessories. Before the first use, wash all parts, which will be in contact with food, in warm
water with a mild detergent, thoroughly rinse in clear water and wipe dry or let dry. Put the
assembled food processor with the selected attachments on a flat, stable, smooth and
clean worktop, out of reach of children and incapacitated people. Provide sufficient free
space for ventilation. The appliance openings allow free airflow for ventilation, and must
not be covered or otherwise blocked. The feet must not be removed. Electric power socket
must be easily accessible to allow easy disconnecting of the food processor in the case of
emergency.

III. 1) FOOD PROCESSOR AND ATTACHMENT

Description (Fig. 1)
A1 – Multifunctional head release
lever/button
A2 – Speed regulating knob
A3 – Bottom mount for adapters C1 – C3
A4 – Front mount for attachments
A5 – Release button

B1 – Stainless bowl

A6 – Removable cover
A7 – Multifunctional head
A8 – Cover
A9 – Mount for attachments (F)
A10 – Power cord

FOOD PROCESSOR CONTROL

TILTING THE MULTIFUNCTIONAL HEAD DOWNWARD/UPWARD (FIG. 2)
Rotating the release lever A1 slightly will lift the head upward. Rotating the lever A1 further
and pushing the unit down will tilt the head downward.

ON/OFF SWITCHING OF THE FOOD PROCESSOR

Before you switch on the food processor, plug the A10 power cord into electric socket.
Then switch on the food processor by rotating the speed regulating knob A2. After you
finish working, switch off the food processor by rotating the speed regulating knob to
position 0 and unplug the power. from the mains.

SPEED CONTROL (FIG. 5)

Speed is controlled by setting the speed regulating knob A2 to the desired position
within the interval 1 – 2 – 3 – 4 – 5 – 6. For short operation time at the maximum speed, the
regulating knob can be set to position “P” (PULSE). The regulating knob must be held
by hand in this position. Releasing the regulating knob will return it to position 0 and stop
rotating.

MULTIFUNCTIONAL HEAD ATTACHMENT SECURITY SAFEGUARD

In order to disassemble the food processor and to remove the attachments from A4 front
mount for attachments, apply a reverse procedure. Before removing the attachments from
the motor unit head, you first have to push the release button A5.

BLENDER SECURITY SAFEGUARD

The food processor cannot be switched on, if the blender cover A8 is removed, and the
blender is not correctly fixed.

Food processing time depends on the volume, type and quality of the processed
ingredients. It usually takes several minutes under normal conditions.

III. 2) WHIPPING, MIXING WHISK, KNEADING HOOK

Description (Fig. 1)
C1 – Mixing whisk
C2 – Whipping (wire) whisk
C3 – Kneading hook

Safety hints and tips

• With regard to the bowl size, please note that the food processor is not able
  to sufficiently whip/knead very small amounts of food. For optimum results input
  at least 300 g of food (if you are whisking egg-whites, use at least 2 eggs).

• Never fill the bowl with water or other liquid to the maximum level. Respect the
  maximum allowed capacity (see the Table of Use, Chapter IV.).

• When tilting the multifunctional head upward, control / slow down its rotation by hand.

• The food processor is fitted with a security safeguard, which will switch off the motor
  once the multifunctional head is tilted upward (during operation). After the head is
  titled back into the working position, the motor will remain switched off. To turn it on,
  you have to return the speed regulating knob A2 to position 0.

ASSEMBLY FOR WORK WITH ATTACHMENTS

Assemble the food processor according to instructions in Figure No. 2, 3 and 4 by lifting
the multifunctional head up. Then put the bowl with the food in the lower section of the food
processor. Then install the desired adapter on the mount, and tilt the multifunctional head
downward to the working position. Apply reverse sequence to remove/exchange the adapter.

USE

A) Whipping

• Use the whipping whisk C2 to whip cream, eggs and egg-whites.

• Adjust the processing speed according to the volume, type and quality of the
  food you are processing, in the interval 1 – 6.

• The maximum amount of food per processing cycle is 1.2 l.

• Never use the whipping whisk for kneading heavy dough or mixing light dough!

B) Mixing

• Use the mixing whisk C1 for light dough, cake mixtures, cookies, glazes, fillings,
  mashed potatoes, etc.

• Adjust the processing speed according to the volume, type and quality of the food
  you are processing, in the interval 1 – 4.

• The maximum amount of ingredients per processing cycle is about 2,5 kg.

• Never use the mixing whisk for kneading heavy dough!

C) Kneading

• Use the kneading hook C3 for kneading crispy / light / heavy dough.

• Adjust the processing speed according to the volume, type and quality of the food
  you are processing, in the interval 1 – 2.

• If you process a larger amount of dough, process it in several batches. The maximum
  amount of ingredients per processing cycle is about 1.3 kg. Do not run more than four
  consecutive cycles. Make a break of at least 30 minutes before you continue.

III. 3) GLASS BLENDER (F)

Description (Fig. 6)
F1 – Container lid
F2 – Container support
F3 – Knife

F4 – Knife sealing
F5 – Removable stopper
F6 – Glass container

Safety hints and tips

• Do not let the blender running without any food!

• Do not remove the knife support F2 from the glass container!

• Never pour boiling liquids in the container. High temperature could damage the
  container and cause breaking the glass. Always put the lid and stopper on the
  container before on-switching the appliance. Never remove the container lid F1 when
  the motor unit is running.

• Before removing the blender lid or container, wait until the rotating parts completely stop.

• When mixing liquids, never use larger volume than the level marked on the container.

• You may also process hot liquids up to 80 °C, for example sauces or soups.

ASSEMBLY

Assemble the blender and attach it to the blender mount A9 according to Figures 6 a 7.
Insert the removable stopper F5 in the lid opening. Apply reverse sequence to disassemble
the unit and to remove it from the mount.

BEFORE THE FIRST USE

We recommend washing the glass container before using it for the first time. The knife
section is treated with oil not harmful to health for technological reasons. Therefore first fill
in the container with warm water (max. 50 °C) with a small amount of detergent.
Then put the container on the food processor, set the maximum rotational speed and
run for 1 minute. Then rinse the container with clear water.

USE

The blender is designed to mix juices, milk cocktails, soups, sauces, children food and
dietetic food, light dough, biscuit dough, puree, etc. Remove the lid, put or pour the food
into the container and replace the lid. Always set the speed with regard to the kind and
amount of ingredients being processed, and particularly with regard to ripeness of fruit and
vegetables. We recommend that you always switch on the blender to minimum revolutions
and then gradually increase the performance as required.

The recommended processing speed is 1 – 6.

Tips

• When the appliance is in operation, it is only possible to add liquid ingredients
  (e.g. water, milk, oil, etc.).

• If you are going to process larger amount of food, divide it into batches not to overload
  the motor unit of the multifunctional head.

• Cut tougher substances into small pieces, otherwise the knife F3 will soon become blunt.

• If you are going to mix ice cubes, their size should not exceed 40 x 40 x 20 mm,
  otherwise the knife F3 becomes blunt or the motor unit is overloaded.

• Never fill the container with liquids producing foam (for example milk) up to „MAX“
  level to prevent overspill. We recommend 1 litre at maximum.

• Soak hard food (such as legumes, soybeans, etc.) in water before further processing.

IV. TABLE OF APPLIANCE USE AND ATTACHMENTS

Please consider the following processing tips as examples and inspiration. They are not
intended as complete instructions, they just show possible variants of food processing.
Choose the volume of the processed food so that the maximum volume of containers will
not be exceeded. Larger volumes must be divided into several batches, and the container
level must be continuously checked. We recommend occasional interrupting of operation,
switching off the appliance and removing any food stuck on or blocking attachments.

Attachment

|

Food

|

Max. amount

|

Time (min.)

|

Speed

---|---|---|---|---

Mixing whisk  (C1)

|

r

e

h

t

e

g

o

t

/

e

p

i

c

e

R

|

Plain flour

|

1000 g (1330 ml)

|

2 to 5

|

1 – 4

Powdered sugar

|

500 g (625 ml)

Milk

|

400 ml

Eggs

|

8 pcs (360 ml)

Oil

|

250 ml

Total volume

|

3000 ml

Whipping

whisk (C2)

|

Cream (incl. 38 % fat)

|

1200 ml

|

10

|

1 – 6

Egg-white

|

15 pcs

|

5

|

6

Kneading

hook (C3)

(bread / *

gluten-free

bread recipe)

|

r

e

h

t

e

g

o

t

/

e

p

i

c

e

R

|

Flour

|

800 g

|

1 minute at 1, then higher speed (max. 2) for 4 minutes

Salt

|

8 g

Yeast

|

12 g / * 18 g

Sugar

|

8 g / * 0 g

Water

|

465 g / * 280 g

Fat

|

8 g / * 0 g

Blender (F)

|

Milk

|

1000 ml

|

2

|

1 – 6

Carrot (max. 4 cm)

|

250 g

Ice (30 x 20 x 20 mm)

|

340 g

V. MAINTENANCE

Do not use harsh and abrasive detergents for maintenance and cleaning! Ensure
that the contact surfaces and sealing elements are clean and functional. You can use
a dishwasher to clean the following parts – accessories C1-C3, the whole blender F except
the removable blade F3. Some foods may colour the respective attachment to a certain
extent. However this shall not have any effect on the appliance operability and does not
constitute a reason to file a complaint! The colouring will usually spontaneously disappear
after some time. Never dry plastic mouldings above a heat source (such as stove,
electric/gas oven).

1) Multifunctional head and food processor body A
Clean them with a damp cloth soaked in water with a detergent. Avoid water getting
in the internal components! If the power cord becomes dirty, wipe it with a damp cloth.

2) Stainless bowl B1
Clean the component with a cloth soaked in water with a detergent. Do not use steel wool,
wire brush or bleaching agent for cleaning. Remove lime sediments with vinegar.

3) Whipping/mixing whisks and kneading hook C1, C2, C3
Immediately after use, wash the attachments in hot water with a detergent and let dry out.

4) Blender F
Immediately after use, wash the attachments in hot water with a detergent and let dry out.
Knife cleaning procedure: pour about 0.5 l of clear water in the container, switch on the
appliance and remove the impurities by several pulses. In the case of larger amount of
impurities, repeat the procedure several times, or pour 1 litre of water, add a small amount
of detergent and switch on the blender for 1 minute. For easier cleaning, take the knife F3
from the blender base F2 according to Fig. 6. To release the knife F3, use the removable
stopper F5.

Sealing replacement procedure

Proceed according to Fig. 6. If the sealings F4 is worn or damaged, replace it with a new
one (of identical type ETA412800225).

More extensive maintenance or maintenance requiring intervention in the inner parts
of the appliance must be carried out by professional service! Failure to comply with
the instructions of the manufacturer will lead to expiration of the right to guarantee
repair!

VI. STORAGE

Store the properly cleaned appliance including all accessories and attachments at a dry,
dustless and safe place, out of reach of children and incapacitated persons.

VII. ENVIRONMENT

If the dimensions allow, there are marks of materials used for production of packing,
components and accessories as well as their recycling on all parts. The symbols specified
on the product or in the accompanying documentation mean that the used electrical
or electronic products must not be disposed of together with municipal waste. For proper
disposal, hand them over at the special collection places where they will be accepted free
of charge. Suitable disposal of the product can help to maintain valuable natural resources
and to prevent possible negative impacts on the environment and human health, which
could be the possible consequences of improper waste disposal. Ask for more details at
the local authority or at a collection site. Fines can be imposed for improper disposal of this
type of waste in agreement with the national regulations. If the appliance is to be put out of
operation, after disconnecting it from power supply we recommend its cutoff and in this way
it will not be possible to use the appliance again.

VIII. TECHNICAL DATA

Voltage (V) Shown on the type label of the appliance
Input power (W) Shown on the type label of the appliance
Weight (kg) approx. ca 6,8
Volume of the stainless steel bowl (l) 5,5
Volume of the blender jug (l) 1,5
Protection class of the appliance II.
Input in off mode is < 0,50 W
Noise level: Acoustic noise level of 86 dB(A) re 1pW

The manufacturer reserves the right to change the technical specifications and
accessories for the respective models.

WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING
OR IN THE INSTRUCTIONS MANUAL:

HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS.

PLEASE DO NOT OPEN DURING THE OPERATION. NEVER PUT INTO THE HANDS WITH  POWER ON

|

TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG  AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN  CRIBS, BEDS, ARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

|

CAUTION: DO NOT PUT FINGERS OR OTHER ITEMS INSIDE

|

CAUTION

References

• AEG Hausgeräte | Setzen Sie auf Qualität | AEG
• ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>