cecotec Popstar 3000 Upholstery Vacuum Cleaner Instruction Manual

cecotec Popstar 3000 Upholstery Vacuum Cleaner

Product Information

The Conga PopStar 3000 CarpetClean is an upholstery cleaner designed for domestic use. It is not suitable for commercial purposes. The device should not be placed near heat sources.

SAFETY INSTRUCTIONS

Please, keep this instruction manual in a safe place for future reference or new users.

• Read these instructions carefully before assembling or using your Conga PopStar 3000 CarpetClean upholstery cleaner. These instructions contain important information that will help you get the best out of your equipment. It is your responsibility to make sure every user is informed about the warnings and precautions stated in this instruction manual.
• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance should not be carried out by unsupervised children.
• This appliance is designed for domestic use only and is not intended for bars, restaurants, farmhouses, hotels, motels, and offices.
• WARNING: check that the upholstery cleaner and package are not damaged. Never use the device if it is damaged. Should it be the case, immediately contact Cecotec’s Technical Support Service.
• Packaging material may be dangerous to children. Remove it and place it out of their reach.
• The upholstery cleaner plug must be connected to a grounded socket. If you do not have a grounded socket, a grounded installation must be carried out by a licensed electrician. In case of ungrounded use, Cecotec shall not be liable for any malfunction or damage that this may cause.
• Make sure that the mains voltage matches the voltage stated on the product marking and that the wall outlet is grounded.
• Always use the plug provided with the device. Do not modify the plug provided with the appliance if it does not match the power socket.
• Check the power cord regularly for visible damage. If the cord is damaged, it must be repaired by the official Technical Support Service of Cecotec to avoid any type of danger.
• Do not operate the appliance if its cord, plug, or structure show visible damage, do not operate properly or produce unusual sounds or odours.
• In case of malfunctioning, repairs must be carried out by the official Technical Support Service of Cecotec; otherwise, the warranty will be void.
• To unplug the device, pull from the socket, never from the cord.
• Do not immerse the cord, plug, or any other part of the appliance in water or any other liquid or expose electrical connections to water. Make sure your hands are dry before handling the plug or switching on the appliance.
• Disconnect the appliance from the electric circuit when it is not used.
• Disconnect the device from the power socket before carrying out any maintenance, cleaning, or transport.
• Do not use the device with pesticides, dyes, lubricants or other liquids.
• Do not use the appliance to vacuum lighted matches, cigarette ends, petrol gas, sources of heat or hot ash.
• Do not use the device without installing the waste-water tank.
• The device is designed to clean carpets and upholstery, do not use it for any other purpose.
• This device is designed for personal use only and is not suitable for commercial use.
• Do not place the device near sources of heat, flammable substances, etc.
• If any strange object blocks any of the parts or you vacuum any strange object, stop using the device, empty it and clean it to be able to use it again.
• This product is used to remove dirt through rinsing. Use tap water or alkaline ionised water at a temperature below 40ºC.
• This product cannot be used to clean arts and crafts, non-waterproof fibres (nets, acetic acid, rayon, etc.), non-waterproof products (furs, leather products, white wooden furniture, tea sets, etc.) and vulnerable surfaces (floors, tables).
• When the waste-water tank exceeds the maximum water level, stop operating the device immediately and empty the waste-water tank before using the product again.
• When using detergent, dilute a low-foaming detergent with water and spray it over the object to be cleaned.
• When using detergent, make sure it will not leave any stains before using it.
• If you use the device over a shag carpet, this will block the water outlet and the machine may stop working.
• If there is too much foam or waste water in the lower part of the machine during operation, stop using it immediately and clean the tank before using it again.
• Do not use a detergent that foams.
• Do not try to vacuum the following objects:
  • Large quantities of dust (extinguishing agent, etc.)
  • Large quantities of sand and pebbles
  • Large quantities of waste
  • Metals like needles and pins, glass, etc.
  • Large and medium plastic bags
  • Objects which tend to accumulate indoors

Protective device

• If the fan stops working correctly, the protective device will start running to prevent the motor from overheating, and the machine will not work for a short period of time, even if you turn it on.
• If the protective device is activated:
  • Press the power button and disconnect the device plug.
  • Store the device in a cool place.
  • After 1 hour, the protective device will deactivate automatically, and you will be able to use the appliance again.

PARTS AND COMPONENTS

Fig. 1

1. Power button
2. Clean-water tank release tab
3. Clean-water tank
4. Main body
5. Hose
6. Hose hook
7. Water release button
8. Hose bracket
9. Plug
10. Waste-water tank
11. Waste-water tank release tab
12. Handle
13. Power cord holder
    • To transport the device, you can wind the hose around the machine and tie and hang the power cord in its hook, as shown in Figure 1.
    • Attachments
    • Fig. 2
    • A. Water suction nozzle with brush, to be used on carpets, etc.
14. Suction inlet
15. Brush
16. Water outlet
    • Right-angle suction nozzle, for narrow slots and seat backrests
17. Suction inlet
18. Water outlet

BEFORE USE

• This product includes a safety package to protect it during transport. Unpack the device and keep the original packaging and materials in a safe place. It will help prevent any damage if the product needs to be transported in the future. In case the original packaging is disposed of, make sure all packaging materials are recycled accordingly.
• Make sure all parts and components are included and in good conditions. If any sign of visible damage is observed, immediately contact Cecotec’s official Technical Support Service.

Box contents

• Upholstery cleaner
• Right-angle suction nozzle
• Water suction nozzle with brush
• Clean-water tank
• Waste-water tank
• Hose hook
• Water tank cap
• Instruction manual

ASSEMBLY

1. Insert the hose hook (6) in the device (4). Fig. 3
2. Remove the clean-water tank (3) from the main body of the device (4). To do so, slide the clean-water tank release tab (2) and remove the tank (3) in the direction of the arrow shown in figure 4.
3. Turn the clean-water tank (3), loosen the cap, and fill the tank with clean water. Themaximum water capacity is 1.2 litres approximately and it is marked in the tank with ‘MAX’. Fig. 5
4. Install the clean-water tank (3) again in the main body of the device (4). Fig. 6
5. Insert the hose bracket (8) in the suction nozzle (A/B). The holes on both pieces must match during assembly. Fig. 7

Warning

• After filling the tank with water (3), you must tighten the cap correctly to avoid leakage.
• You can add low-foam detergent to the clean-water tank (3), combined with water in a 5:10 proportion.
• After using your device, you must empty the remaining water in the clean-water tank (3) to avoid leakage and mould formation.
• Do not shake the clean-water tank (3) during installation, as it could cause water leakage.

OPERATION

1. Plug the device into a power supply. Fig. 8
2. Press the power button (1) to turn the device on. Fig. 9
3. Hold down the water release button (7) to spray clean water (Fig. 10). Spray clean water over the dirt to bring it to the surface.
4. Press the vacuuming inlet (18) on the dirt to bring water and dirt to the surface and vacuum them. Fig. 11
5. Stop spraying clean water and vacuum the waste water (Fig. 12). After using the device, dry the surface with a dryer or let it air dry.
6. Switch off the device by pressing the power button. Fig. 13
7. Disconnect the device from the power supply.
8. Empty the clean and waste water from the tanks and clean the waste-water tank.

Warning

• Do not spray water continuously over the same spot.
• Take special care when using the device to clean stairs.
• After using the device, hang and wind the power cord in the power cord holder.

Cleaning embedded dirt

Warning:

• You can add low-foam detergent in the clean-water tank or apply it directly on the stain.
• Make sure the detergent will not damage the soiled surface before using it.
• Do not use thinners, aniline, chloroform or flammable detergents.

Recommended liquids

• Alkaline ionised water.
• Low-foam detergent to the clean water tank combined with water in a 5:10 proportion.
• Citric acid
• Water with hydrochloric acid.

Non-recommended liquids

• Neutral kitchen detergent.
• Alkaline detergent.
• Acid detergent.

1. Apply detergent over the soiled surface, spray clean water and scrub the dirt with a brush (19) to bring it to the surface.
2. Vacuum the dirt and do not let any detergent remain. Fig. 14

Warning

• To know the detergent quantity and use, carefully read the manufacturer instructions.
• Stop using the device when the water or foam in the waste-water tank (12) reaches the maximum water level and clean the waste-water tank (12); otherwise, water may enter the machine.

Using the right-angle suction nozzle

• Press the suction nozzle against the soiled surface and move it from top to bottom. Fig. 15

CLEANING AND MAINTENANCE

Warning

• Stop the device and unplug it from the mains before cleaning it.
• Do not wet the device to avoid the risk of electric shock.
• Do not use detergents, thinners, benzene or other chemical agents to clean the device.
• After every use, you must remove and clean the waste-water tank (12), the clean-water tank (3) and the suction nozzle (A/B) to prevent humidity and dirt remains from emitting bad odours. Fig. 16

Cleaning the main body

• The most common dirt can be cleaned with a slightly damp cloth.
• The most stubborn dirt can be cleaned with a cloth slightly soaked in detergent and then a cloth slightly soaked in water.

Cleaning the waste-water tank

1. When the waste water reaches the maximum level (11), stop using the device and unplug it from the mains.
2. Remove the waste-water tank (12). To do so, slide the waste-water tank release tab (13) and remove the waste-water tank (12) in the direction of the arrow shown in Figure 17.
3. Remove the upper cover of the waste-water tank and empty the waste water. Fig. 18
4. Clean the tank, the upper cover and the sealing strip. Fig. 19
5. Install the sealing ring in the cover and secure it to the tank, making sure the holes (29) match the tabs (28). Fig. 20
6. Place the waste-water tank (12) in the main body of the device (4). Fig. 21
   • Figure 20:
   • 19. Tabs
   • 20. Holes

Warning

• Do not lean or shake the waste-water tank when transporting or assembling it; otherwise, waste water will easily leak.
• We recommend you empty the waste water before it exceeds the maximum level on the tank (11); if you continue using the tank after the waste water has exceeded the maximum water level (11), the float valve (31) will automatically stop the machine vacuuming water (30). Fig. 23
  • Figure 22:
  • 21. Automatic vacuuming stop device
  • 22. Float valve

Cleaning the clean-water tank

1. Remove the clean-water tank (3) in the arrow direction, as shown in the assembly section. Fig. 4
2. Loosen the cap and empty the remaining water. Fig. 23
3. Tighten the cap of the clean water tank again (3) and install the empty tank.
4. Press the power button (1) to turn on the device. Fig. 24
5. Press the water release button (7) to empty the remaining water in the device. Fig. 25
6. When it stops releasing water, turn off the device and unplug it from the mains.
7. Tilt the machine and empty the remaining water at the bottom of the device. Fig. 26

Cleaning the suction nozzle

1. Press the suction nozzle release button (32) and separate it from the hose bracket (8). Fig. 27
2. Remove the front cover (33) by lifting it with your finger. Fig. 28
3. Rinse the suction nozzle.
4. Install the suction nozzle cover again. Make sure the pins are correctly placed in the holes and press these parts until they click. Fig. 29-30
   • Figure 28-29:
   • 23. Suction nozzle release button
   • 24. Suction nozzle front cover
   • 25. Holes
   • 26. Pins

• When cleaning the suction nozzle, empty the water outlet (20) if clogged. Fig. 31
• Check the hose (5) is not damaged and has no leaks. Fig. 32

Cleaning the air inlet sponge and the filter sponge

1. Rinse the air inlet sponge (36) and the filter sponge (37) after every use and replace them if worn.
   • Figure 33
   • 27. Air inlet sponge (located on the bottom of the waste-water tank)
   • 28. Filter sponge (located on the bottom of the clean-water tank)

• We recommend removing them with tweezers.
• Let them air dry after cleaning.
• Install the parts again in the machine after cleaning.
• After cleaning it, store the machine in a dry place at room temperature and avoid direct sunlight.

TROUBLESHOOTING

If you observe any problem, carefully read this manual and try any possible solutions before contacting Cecotec’s Technical Support Service.

• If after these tasks the problem still occurs, contact the provider or Cecotec’s Technical Support Service.

Warning

• Do not try to disassemble, repair or modify the device by yourself.

TECHNICAL SPECIFICATIONS

• Product: Conga PopStar 3000 CarpetClean upholstery cleaner
• Reference: 05082
• Voltage: 220-240 V, 50/60Hz
• Power: 400 W
  • IPX4
• Actual waste-water tank capacity: around 0.5 litres
• Actual clean-water tank capacity: around 1.2 litres.
• Hose length: φ30 mm x 1.2 m
• Dimensions: 290 mm x 180 mm x 270 mm
• Technical specifications may change without prior notification to improve product quality.
• Made in China | Designed in Spain

DISPOSAL

DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC APPLIANCES

This symbol indicates that, according to the applicable regulations, the product and/or cells must be disposed of separately from household waste. When this product reaches the end of its shelf life, you should dispose of the cells/batteries/accumulators and take them to a collection point designated by the local authorities. Consumers must contact their local authorities or retailer for information concerning the correct disposal of old appliances and/or their batteries. Compliance with the above guidelines will help protecting the environment.

TECHNICAL SUPPORT AND WARRANTY

Cecotec shall be liable to the end user or consumer for any lack of conformity that exists at the time of delivery of the product under the terms, conditions, and deadlines established by the applicable regulations. It is recommended that repairs be carried out by qualified personnel. If at any moment you detect any problem with your product or have any doubt, do not hesitate to contact Cecotec’s official Technical Support Service at +34 963 210 728.

COPYRIGHT

The intellectual property rights over the texts in this manual belong to CECOTEC INNOVACIONES, S.L. All rights reserved. The contents of this publication may not, in whole or in part, be reproduced, stored in a retrieval system, transmitted, or distributed by any means (electronic, mechanical, photocopying, recording or similar) without the prior authorization of CECOTEC INNOVACIONES, S.L.

Cecotec Innovaciones S. L.

• C/de la Pinadeta s/n, 46930
• Quart de Poblet, Valencia, Spain
• www.cecotec.es

References

• Cecotec Tienda Oficial | Envío Gratis | Mejor Precio

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>