FORTIN THAR-NIS4 Nissan Maxima 2020 Push-to-Start Remote Starters and Alarm Systems Installation Guide

FORTIN THAR-NIS4 Nissan Maxima 2020 Push-to-Start Remote Starters and

Alarm Systems

Product Information

lights Tachometer Autolight Off Door Status Trunk Status Hood
Status* Hand-Brake Status Foot-Brake Status OEM Remote Monitoring
Push-to-Start Control

Product Usage Instructions

To install the THAR-NIS4 product, follow these steps:

Mandatory Installation

The installation of safety elements is mandatory. The hood pin is an essential security element and must be installed. This module must be installed by a qualified technician. A wrong connection can cause permanent damage to the vehicle.

Program Bypass Option

To program the bypass option, follow the instructions below based on the desired configuration:

function A11 to OFF.
D1.10| OR| Program bypass option with OEM remote: LOCK, LOCK, LOCK
D1.1| UN| Program bypass option with RF KIT antenna: OEM Remote
Monitoring

Remote Starter Diagnostics

The module LED indicator provides diagnostics information:

Additional Requirements

In addition to the THAR-NIS4 product, the following items are required for installation:

• 1x FLASH LINK UPDATER or FLASH LINK MOBILE tool (sold separately)
• 1x FLASH LINK MANAGER software or FLASH LINK MOBILE app (depending on the tool used)
• 1x Microsoft Windows computer with an internet connection or a smartphone (Android or iOS) with an internet connection (provider charges may apply)

It is recommended to cut the warning card provided and stick it on a visible place or use the package RSPB (sold separately). The vehicle can be started by either pressing the lock button on the OEM remote 3 times consecutively or by a smartphone. Turn on the
safety switch located under the dashboard before working on the vehicle.

BCM Connectors

The THAR-NIS4 product is compatible with the following BCM connectors:

• Grey 24-Pin connector
• White 15-Pin connector
• Green 40-Pin connector
• Black 40-Pin connector

ONLY COMPATIBLE WITH AUTOMATIC TRANSMISSION VEHICLES.

MANDATORY INSTALL

HOOD STATUS : THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE STARTED WITH THE HOOD OPEN, SET FUNCTION A11 TO OFF.

Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.

THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.

PARTS REQUIRED (NOT INCLUDED)

STAND ALONE CONFIGURATION

REMOTE STARTER FUNCTIONALITY

REMOTE STARTER WARNING CARD

CUT THIS WARNING CARD AND STICK IT ON A VISIBLE PLACE: or use the package RSPB, Sold separately.

WARNING
REMOTE STARTER
THE VEHICLE CAN BE STARTED BY EITHER: PRESSING THE LOCK BUTTON ON THE OEM REMOTE 3 TIMES CONSECUTIVELY OR BY A SMARTPHONE. TURN ON THE SAFETY SWITCH LOCATED UNDER THE DASHBOARD BEFORE WORKING ON
THE VEHICLE.

DESCRIPTION

• BCM located behind cluster
• BCM Grey 24-Pin connector
• BCM Black 40-Pin connector
• BCM Grey 24-Pin connector
• BCM Green 40-Pin connector
• BCM Black 24-Pin connector

WIRING CONNECTION

DCRYPTOR PROGRAMMING PROCEDURE

• Press and hold the programming button: Connect the 4-PIN Data-link harness (Black connector).
  The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.

• Release the programming button when the Blue LED is ON.
  If the LED are not solid BLUE disconnect the 4-PIN Data-link harness (Black connector) and go back to step1.

• Connect the required remaining harnesses.

• Do not press the brake pedal. Press the Push-to-Start button twice to turn ON the ignition
  The BLUE LED will flash rapidly.

• Press the Push-to-Start button once to turn off the ignition.
  The BLUE LED will turn off.
  The RED and YELLOW LEDs will alternated.

• Disconnect all the connectors and after the Data-Link (4-pins) connector.

• Use the tool:
  FLASH LINK UPDATER or FLASH LINK MOBILE to visit the DCryptor menu.
  Parts required (not included)

• AFTER DCRYPTOR PROGRAMMING COMPLETED
  Go back to the vehicle and reconnect the 4-Pin (Data-Link) connector and after, all the remaining connector.

REMOTE STARTER
PROCEDURE
Test the remote starter. Remote start the vehicle.

The module is now programmed.

REMOTE STARTER FUNCTIONALITY

OPTIONAL RF-KIT PROGRAMMING

PROGRAM BYPASS OPTION

OPTIONAL FORTIN RF KIT SERIES 4 OR SERIES 9 PROGRAMMING

Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a regular basis. We recommend that you update this module to the latest fi rmware and download the latest installation guide(s) prior to the installation of this product.

WARNING
The information on this sheet is provided on an (as is) basis with no representation or warranty of accuracy whatsoever. It is the sole responsibility of the installer to check and verify any circuit before connecting to it. Only a computer safe logic probe or digital multimeter should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or responsibility whatsoever pertaining to the accuracy or currency of the information supplied. The installation in every case is the sole responsibility of the installer performing the work and FORTIN ELECTRONIC SYSTEMS assumes no liability or responsibility whatsoever resulting from any type of installation, whether performed properly, improperly or any other way. Neither the manufacturer or distributor of this module is responsible of damages of any kind indirectly or directly caused by this module, except for the replacement of this module in case of manufacturing defects. This module must be installed by qualifi ed technician. The information supplied is a guide only. This instruction guide may change without notice. Visit www.fortinbypass.com to get the latest version.

TECH SUPPORT

Tél: 514-255-HELP (4357)
1-877-336-7797
ADDENDUM GUIDE

www.fortinbypass.com

WEB UPDATE

References

• wah damn solid

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>