CLAS PE 6000M Mobile Scissor Lift Instruction Manual

CLAS PE 6000M Mobile Scissor Lift

Product Information

• The PE 6000M is a mobile scissor lift with a double cylinder and low raise capability. It has a maximum weight capacity of 3 tons.
• The product is manufactured by clas.com.

Product Usage Instructions

1. Before using the lift, carefully read the contents of the user manual.
2. Packaging, Transport & Storage:
   • Packaging: Refer to image 1 for packaginginstructions.
   • Transport: Refer to image 2 for transport instructions.
   • Storage: Properly store the lift according to the provided guidelines.
3. User Manual Conservation: Ensure the user manual is properly conserved for future reference.
4. Description of the Lift:

The lift has the following specifications:

1. Tension: Interieur
2. Installation Location: Indoor
3. Weight Capacity: 3000kg
4. Minimum Height: 960mm
5. Maximum Height: 105mm
6. Length: 1450mm
7. Width: 530mm
8. Power: 2.2kw
9. Hydraulic Oil Capacity: 12L of H46 hydraulic oil (not provided by the manufacturer)
10. Pont Dimensions: Refer to image 3 for the dimensions of the lift.
11. Installation: Follow the installation instructions provided in image 4.
12. Calibration: Add hydraulic oil according to the instructions and use button SB4 (refer to image 21) for calibration.
13. Operation:
    • Lifting Phase: Follow the instructions for the lifting phase.
    • Lowering Phase: Follow the instructions for the lowering phase.
14. Maintenance: Refer to the appendix for maintenance and troubleshooting information.

WARNING
Before returning this product for any reason (installation problem, instructions for use, breakdown, manufacturing problem…), please contact us.

Contact :

• You can reach us by mail sav@clas.com or by phone +33(0)4 79 72 69 18 or go directly to our website clas.com
• If you have changed your mind regarding your purchase, please return this product before you attempt to install it.

WARRANTY

The manufacturer warrants lifts and the relevant accessories for 12 months after purchase date. This warranty consists in the repair or replacement – free of charge – of those parts that, after a careful analysis by the Manufacturer’s Technical Service, turn out to be faulty from origin. Warranty is limited to material defects, and becomes null and void if the returned parts are tampered with or disassembled by unauthorised staff. Any liability for direct and indirect injuries to people, animals or property due to machine failure or malfunction are excluded from warranty. The expenses deriving from lubricants replacement, transport charges, and any customs duty, VAT and any other expense not specified in the supply contract are at the purchaser’s charge. The replacement and repair of parts under warranty, anyway, do not extend warranty terms. The purchaser will nevertheless be entitled to assert its rights on warranty, specified in the supply contract.

DISCLAIMER
Upon delivery, please check that the product has not been damaged during transportation, and that the accessories coming with it are intact and com- plete. Any complaint shall be filed within 8 days after lift delivery date. Besides the cases envisaged by the supply contract, the warranty becomes null and void:

• In case of a manoeuvre error caused by the operator.
• If the damage is caused by poor maintenance.
• If the envisaged capacity is exceeded.
• If the machine has been somehow modified, and the damage has been caused by such a modification, due to repair operations by the user without the authorisation of the manufacturer or after fitting non-original spare parts.
• If the instructions described in the user’s manual are not complied with.

STANDARDS AND LIFETIME:

• Lifetime of the product: 10 years
• Standards: EN 1493:2010 – EN ISO 12100:2010 – EN 60204-1:2006/AC:2010

CAREFULLY READ THE INSTRUCTIONS GIVEN IN THIS MANUAL BEFORE USING THE LIFT

PACKING, TRANSPORT & STORAGE

Transport

• Packaging can be lifted or moved by lift trucks, cranes or overhead cranes. In case of slinging, a second person must always take care of the load, in order to avoid dangerous oscillations.
• During loading and unloading operations, goods must be moved by appropriate vehicles such as trucks, ships or fork lift.
• At the moment the goods are delivered, verify immediately that all of the items specified in the packing list are included.
• If finding missing parts, possible defects or damages to the goods caused during the transport you should immediately inform the person in charge, or the carrier.
• The lift is really heavy, don’t move it manually, use an appropriate way for your safety. Furthermore, during loading and unloading operations, goods must be handled as shown in the picture. (Picture 2)
• It is important to point out that the goods, during loading and unloading operations, when moved by other than common lift trucks must be handled as shown in Image 2.

Storage:

• The equipment should be stocked inside the warehouse, if stocked outside make sure that the equipment stay off the water.
• Use box tracks for ground transportation , use container when shipping.
• Control box should be placed perpendicularly during the transport to prevent it to crash against other goods.
• Temperature range for machine storage: min -25ºC – max + 55ºC

INTRODUCTIONS

The following manual is provided for experienced and specialized personnel in the use of lifting equipment such as lifting operators and technical personnel responasable of the installation and the ordinary maintenance of the machine.
It is recommended that the personnel carrying out tasks/operations with the lift carefully read the «Operation and Maintenance Manual».

The following manual provides important information regarding:

• Personal safety of the operators and the maintenance workers.
• Lift safety
• The safety of the vehicles being lifted

CONSERVING THE MANUAL

• This manual is an integral part of the lifting equipment.
• This manual must be kept nearby the lift, so that the operator and the maintenance staff can easily locate it and consult it at any time.
• We particularly recommend reading Chapter 3 which contains important information and safety warnings.

The lift is designed and manufactured according to the European Standard

• Lifting, transport, unpacking, assembly, installation, starting up, initial adjustment and testing, extraordinary maintenance, repair, overhauls, transport and dismantling of the lift are all operations that must be performed only by specialized personnel or by licensed dealer authorized by the manufacturer.
• The manufacturer declines all responsibility for injury to persons or damages to vehicles and objects when any of the above mentioned operations has been performed by unauthorized personnel or when the lift has been subject to improper use.
• This manual indicates: the operative and safety aspects that may be useful to the operator and maintenance workers. For a better understanding of the structure and its functioning, workers must carefully read the ‘Maintenance & Use Manual’.
  • To ensure a better use of the equipment, it is necessary to understand the terminology used in this manual, to know the maintenance and repair activities, to be able to correctly interpret the technical drawings and descriptions contained in the manual, and be aware of the regulations in force in the country where the machine is installed.
  • The same requirements are also asked for the maintainer and installer, who must also possess specific and specialized knowledge in both mechanical and engineering fields.
• OPERATOR: person authorized to use the lift
• MAINTENANCE FITTER: person authorized for routine maintenance on the lift.

Manufacturer reserves the right to make changes to this user manual if technological improvements occur.

DESCRIPTION OF THE LIFT

How to use:
The lift is designed to lift any type of vehicle with a weight below 3000 kg and it is suitable to be used for vehicle testing, maintenance and car cares. It is suitable for recessed or floor installation, without the need for special structures.

Structure Features:

• Scissor structured, equipped with holes for construction and anchoring on the ground.
• The structure is designed to occupy as little space as possible.
• Low voltage independent and movable control unit, with excellent safety level.
• Hydraulic power factor correction
• Equipped with safety valve and anti-theft system to prevent from overload or from the default of the hydraulic system, in this way if the oil pump crashes, the lift platforms do not descend suddenly.
• Equipped with a lowering system of the platforms by the use of a manual pump for those situations of absence of electric power.
• Equipped with high quality elements Made in Italy & Germany.

Equipment:

• Full Lifter
• Control unit

Frame:
Main lifting platforms and electro-hydraulic control unit for mobile control.

• Control unit:
  • On the lift are the containment tank of the hydraulic oil, the hydraulic pump, the hydraulic oil valve. The control panel is mounted on the control cabinet of the control unit.
  • On the mobile trolley is the reservoir for the hydraulic oil, the hydraulic oil valve. The control panel is mounted on the control panel of the control unit.
• Conditions of use:
  The lift is designed to lift any type of vehicle with a capacity below 3000 kg and is suitable for use in vehicle testing, maintenance and car care.

This model can easily be moved using the following optional devices:

• 1 directional steering wheel
• 3 wheel brackets

SPECIFICATIONS

230V ± 5% 50Hz or (60HZ optional)

Engine power| 2.2kw
Hydraulic oil| 12L of Hydraulic Oil type H46 (Not supply by the manufacturer)
Working temperature| From + 5°C to +40°C
Working Humidity Range| 30-95%
Noise level| < 76db
Installation height| Height above the sea level £1000M
Storage Temperature Range| -25°C ~ 55°C
Installation place| Inside

Lift dimension picture

Engine

• Type Y90L
• Power 2.2kw
• Voltage AC 400 or 230V ±5%
• Current 400V ac: 20A 230V ac: 40A
• Frequency 50Hz (or 60 HZ- on request)
• Poles 4
• Speed 1450 rpm/min
• Building shape B14
• Energetic Class F

Pump

• Type P1.7
• Model Hydraulic pump
• Maximum Flux 1.7cc
• Joint type direct joint
• Pression 280 bar
• Adjustable working pressure 150~300 bar

Installation scheme for scissor lift:

• Concrete type 425#, drying time is 15 days.
• Thickness of concrete ≥150mm, alignment of the entire lenght ≤5mm.

The minimum concrete thickness and leveling are the key features that must be respected in order to ensure the correct alignment of the deck.

PARTS OF VEHICLES TO PAY ATTENTION TO:
THE LOWER PARTS OF VEHICLES, LIKE SPORTIVE CAR UNDERBODY, CAN MAKE INTERFERENCE WITH THE STRUCTURAL PARTS OF THE LIFT.

• The lift will also handle custom or non-standard vehicles, provided that they are within the maximum specified load capacity.
• The personal safety area must also be defined in relation to the non-standard vehicle.

SAFETY

It is recommended that you read this chapter carefully and thoroughly as important notions about the safety regulations to be adopted by the operator and other users are provided, also in the event of improper use of the lift. The following text provides clear explanations of certain situations of risk or danger that may arise during use or maintenance of the deck. It is also illustrated the installed security device, indicating the correct use of this system, the residual risks and the operating procedures to be used (general precautions to eliminate potential dangers).

The lift is designed and built for lifting vehicles and to keep them lifted to the desired position in a circumscribed environment. Any other use of the lift is forbidden.

Especially, lifts are not suitable for:

• spray washing vehicles;
• persons lifting;
• crushing purpose through pressure system;
• used as elevator;
• used ad single vehicle parts elevator.

The manufacturer is not responsible for any injury to persons or damage to vehicles and other property caused by the incorrect and unauthorized use of the lifts.

• During the lifting or lowering phase, the operator must remain in the station control zone as shown in the diagrams.
• As shown in the diagrams, the presence of personnel within the specified danger zone is strictly forbidden. During the up and down operations of the deck, personnel are allowed in the area of interest only when the vehicle is already in a high position, when the platforms are in a stationary position and when the mechanical safety devices are firmly engaged.

Do not use the lift without protective devices or with the protective devices inhibited. Failure to comply with these regulations may cause serious injury to persons, and irreparable damage to the lift and the vehicle begin lifted.

GENERAL PRECAUTIONS
The operator, installer, and maintenance personnel are required to comply with the applicable safety regulations in the country where the lift is installed.

In addition, the operator, installer and maintainer must:

• Always work at the stations specified and illustrated in this manual;
• Never remove or disable mechanical, hydraulic, electrical, or other types of safety devices;
• Read the safety notes on the machine and the safety information contained in this manual.

All of the following security messages are shown in this manual:

• WARNING: Indicates operations that are not safe and can cause minor injuries to persons, damage to the lift, vehicles or other property.
• CAUTION: Indicates a possible danger that can cause serious injury to persons and property damage.
• RISK OF ELECTRIC SHOCK: A specific safety warning on the lift in areas where the risk of electric shock is particularly high.
• RISK AND PROTECTION DEVICES
  We will now consider the risks to which operators and maintenance personnel can be exposed when the vehicle is in position on the lift, together with the various safety and protection devices adopted by the manufacturer to minimize these dangers.

For a better personal safety and vehicle safety, observe the following rules:

• Do not enter the danger zone when the vehicles are lifted.
• Make sure the vehicles are positioned correctly. (Picture 6)
• Make sure to lift only permitted vehicles, never exceed the specified load capacity, maximum height and projection (vehicle length and width);
• Make sure that there is no person on the platform during the lift up and down movements and while the vehicle is in the highest position.
• 

GENERAL RISKS FOR LIFTING AND DESCENDANT PHASES:

• The following safety devices are used to protect against overload and to avoid engine failure. In case of overload, the safety valve opens and draws the oil back to the tank (see image 8).

• Each cylinder is equipped with a parachute valve; In the event of malfunction or breakage of the oil pipe along the circuit, the affected parachute valve will come into operation and will limit the lowering speed of the platform. (See image 9).

• If there is a break in the oil pipe, or if there is an obstacle that does not allow a platform to perform climb or descent operations, it will trigger a device that will block the other platform as well. (See image 9)

• RISKS FOR PERSONNEL
  All potential risks to the operator, maintenance worker, installer, and any other person present in the lifting area of the lift are result from an improper use of the lift.

• RISKS IN USING THE LIFT

  • During lifting and downhill operations, the personnel must position themselves in the safety zone according to the rules and instructions provided.
  • During uphill and downhill operations, no person is allowed to work under the moving parts of the lift but must operate in the safe area.

• RISK OF IMPACT (Picture 10)
  Before starting to lift the platforms up and down, the operator must make sure that there are no people inside the hazard zone. When, for operational reasons, the lift is stopped at a relatively low height (with a height below 1.75 meters above the ground), make sure to avoid impact with parts of the machine not marked with special colors.

• RISK OF FALLING OFF – PERSONNEL
  During up and down operations personnel are prohibited from entering the platforms and the vehicle lifted to avoid falling off.

• RISK OF FALLING – VEHICLE (Picture 11)
  This danger may arise if the vehicle is incorrectly positioned on the platform or in the case of vehicles of a size/or weight that does not conform to the lifting capacity. When the lift is in use, the engine of the lifted vehicle must not be switched on. You should not place any object on the platform and on the mobile parts of the lift but vehicles.

• RISK OF SLIDE
  Any lubricant contamination in the underlying area and immediately around the lift and the platforms must be cleaned immediately. Immediately remove any oil spills. Keep the working area clean.

• RISK OF VEHICLE FALL FOR WRONG POSITIONING (Picture 12)
  The center of gravity of the vehicle must be located in the lift area shown in image 12

• RISK OF ELECTRIC SHOCK
  The risk of electric shocks in isolated areas of electrical equipment has been canceled. Do not use water jets, steam or paint solvents next to the lift and the control unit, and pay special attention to keeping these substances away from the electrical control panel.

• RISKS RELATED TO INAPPROPRIATE LIGHTING
  The operator, installer and maintenance personnel must be able to ensure that the area where the lift is operating is illuminated properly and uniformly in accordance with the laws in force at the place of installation.

INSTALLATION

THE EXECUTION OF THESE TRANSACTIONS MUST BE CARRIED OUT ONLY BY AUTHORIZED AND COMPETENT PERSONNEL, ALL THE INSTRUCTIONS GIVEN BY THIS MANUAL SHOULD BE FOLLOWED TO PREVENT POSSIBLE DAMAGE TO THE LIFTER OR RISK OF INJURY TO PERSONS.

Only the skilled technicians appointed by the manufacturer or their authorized dealers are authorized to install the lift.

INSTALLATION REQUIREMENTS

• The security distances from the walls must be at least 1000 mm, taking into account the space required to work comfortably, the space required for the control station and any escape routes in case of emergency.
• The area must be predisposed for the power supply and the pneumatic supply of the elevator.
• The area where the lifts are installed must have a height of at least 4000 mm.
• The lift must be positioned on a perfectly leveled and sufficiently strong floor. (≥250 kg / cm², concrete thickness ≥ 150 mm)
• All parts of the lift must be sufficiently lighted to ensure that the adjustment and maintenance operations can be carried out safely, with no reflection or glare, which may cause eye problems.
• The integrity of the incoming product must be verified before installing the lift.
• Moving and installing the lift must be done as shown in image 13.
• The lift must be installed respecting the given specific safety distance from wall and from other equipment (Picture 14)

See «TRANSPORTING AND STORAGE» on page 4-5 for transporting and storing the machine.

Platform installation:

• Position the 2 bases in the chosen final position.
• The bottom of the cylinder is in the direction of access to the vehicle.
• Use a forklift or other lifting equipment to move the platform (Picture 13) and make sure that the lift deck safety devices have been activated and locked.
• Avoid operating in the machine’s operating area if the hydraulic system is not fully equipped with oil. When moving the platform, you have to adjust the space between the two bases and make sure that the two bases are parallel.

CONNECTION OF THE ELECTRICAL LINE:
Connect the electrical and hydraulic connections according to the diagrams in this manual. Connect the electrical and hydraulic connections according to the diagrams in this manual. When connecting the oil pipes, pay particular attention to the protection in the pipe joint to prevent foreign elements from entering the circuit and damaging the hydraulic system.

CONNECTIONS OF THE ELECTRICAL CIRCUIT:
Follow the path indicated in the «electrical diagram» to connect the electrical circuit. Only competent personnel are authorized to perform this type of operation

• Open the front cover of the control box.
• Connect the power supply: the 3-phase power cables, 5-pole 400V (5 × 2.5mm cable) have to be connected to the control box at the marked terminal.
• The PE ground cable must first be connected to the marked terminal (image 15) and then to the connections of the 2 bases.
• If the lift is operated at 230V three-phase, a different electrical diagram must be used which must be requested to the manufacturer.

Connection of the upper limit switch (SQ): see the connection on the circuit diagram.

Connection of the lower limit switch (SQ): see the connection on the circuit diagram

OIL PIPES CONNECTION:
Follow the oil pipe connection diagram. Only qualified and authorized persons are allowed to carry out such operations. Refer to the «oil pipe diagram»:

• When connecting the hoses, pay attention to the oil pipe guard to prevent impurities from entering the hydraulic circuit.
• When connecting the oil pipes, be sure not to mistake the oil pipe reference.
• During the standard installation, the control unit is close to the vehicle entry direction. If it is positioned to the right, it is necessary to adjust its oil pipe.

ADJUSTMENT

Add hydraulic oil as instructed.
After installing the elevator as shown in image 4, having the hydraulic/electrical circuit connected, proceed as follows:

• Open the hydraulic oil tank and add 12L of hydraulic oil H46 to the tank; the hydraulic oil is not supplied by the manufacturer.
• Make sure that the hydraulic oil is free of impurities to prevent the solenoid valve malfunction.
• Activate the «MAIN SWITCH» to turn on the power
• By clicking the «UP» button, check whether the engine rotates clockwise (looking down), otherwise turn off the «MAIN SWITCH» and then change the engine phase.

When power is switched on, the high voltage in the control unit is activated. Only authorized personnel can do this.

Oil pressure adjustment:

1. Press the «UP» button, the motor starts to bring the platforms to the maximum possible height.
2. Open the control unit door, press the «UP» and «SB4» buttons (as shown in picture no. 21) for a few minutes until the air has completely escaped from the hydraulic system.
3. Press the «DOWN» button until the platforms stop at the minimum allowed height, press the «SECOND DOWN» button, this way the platforms will reach the closed position.
4. The oil adjustment process is completed.

LIFT TEST:

• Turn on the machine with the MAIN POWER button.
• Press the «UP» button, pay attention to the synchronization and the lifting fluidity.
• Check that there is no leakage of oil.
• During the test of the lift, no person and no object and / or material must be located near the two sides and below the lift. If an anomaly occurs, press the emergency button to stop the lift immediately. After removing the obstacles, repeat the test.

LOAD TEST:

• Bring the vehicle, with a weight not exceeding the maximum lifting capacity, on the plat-form.
• Put the rubber pad on the platforms.
• Press the ‘UP’ button, raise the platforms and pay attention to the synchronization and the fluidity of the lift.
• Check and make sure that there is no leakage on the hydraulic circuit. If an anomaly occurs, press the emergency button to stop it immediately. After resolving issue, repeat the test.

When starting the load test no person or material must be beneath or close to any of the moving parts of the lift. If a failure occurs, press the «EMERGENCY STOP» button to stop it immediately. After removing obstacles, repeat the test.

MODE OF OPERATION

Only skilled and trained personnel are permitted to carry out this operations. Check the procedures as follows.

Operating alerts:

• Before any operation, remove any obstacles from the lifting area of the lift.
• During lifting or downhill, no operator is permitted to remain in the side area of the machine, underneath it or on both platforms.
• Avoid lifting vehicles above the maximum permissible lifting weight.
• When placing the vehicle on the platform, make sure that the body is resting on the provided rubber pads.
• Pay attention to the synchronization of the lift. If there are anomalies, stop each operation in a timely manner, check and resolve the problem.
• When the equipment is not used for a long period of time or at night, the lifting gear must be lowered to the complete closing, remove the vehicle and stop the power supply

Instructions for the electronic drive:

LIFTING PHASE:

• By pressing the ‘UP’ button, the oil pump will start working, entering the hydraulic oil into the cylinder and so the platforms will start to rise.
• By releasing the ‘UP’ button, the oil pump stops immediately and the platforms stop rising.

LOWERING PHASE:

• By pressing the ‘DOWN’ button, the platforms will start to descend.
• By holding down the ‘DOWN’ button the platforms will stop at a height of about 250mm when they have reached the lower limit switch.
• By releasing the «DOWN» button and pressing «SEC. DOWN», the platforms will go down to the closing position.

EMERGENCY STOP:
If malfunctions occur during the ascent or descent phases of the elevator, press the «EMERGENCY STOP» button, which stops the entire operating circuit and interrupts all other operations.

PLATFORM SYNCHRONIZATION:
During the lifting and lowering of the elevator, if the platforms are not at the same level, the photoelectric alignment device will be immediately deactivated, and will only be activated after the platforms have been aligned at the same height.

HYDRAULIC OIL ADJUSTMENT (normal operating conditions):
After installation and calibration of the elevator is completed, the right platform is lower than the left due to air still in the oil cylinder. When adjusting the oil circuit, the elevator should not be operated and no weights should be placed on the platforms. The adjustment process must be carried out as described in chapter 5 «Adjusting the oil pressure».

EMERGENCY PROCEDURE FOR PLATEFORME MANUAL LOWERING (POWER FAILURE):
During the manual lowering of the platforms keep a close observation of the vehicles placed on the deck until the operation is completed. If anomalies occur during the process, immediately close the hydraulic circuit safety valve. The manual lowering process takes place as follows:

• Set the «MAIN SWITCH» button to the «OFF» position Display the drain valve at the side of the hydraulic pump
• By slowly loosening the RED valve end, it will be noticeable that the platforms will begin to descend.
• Always check the correct floor leveling during descendant phase.
• After lowering the platforms, immediately tighten the drain valve screw.
• The manual lowering of the platforms is now completed.

CARE & MAINTENANCE

Maintenance work is only permissible for trained personnel with appropriate skills.

• All pins and upper and lower sliding blocks in the lift must be lubricated regularly.
• Hydraulic oil should be replaced once a year.
• The oil level must always reach the indicated upper limit.
• When replacing the oil make sure that the platforms of the lift are in the closed position, then proceed to the extraction of the old oil.

TROUBLESHOOTING

The engine does not work

| The power cable is not plugged in by the power outlet.| Connect the power cable to the power socket.

The AC contactor does not work.

| If the engine works by forcing the contactor with an isolation rod, replace the contactor.
The limit switch is not closed.| Check     the    limit    switch,    its cable and adjust/ or replace the device.
In lifting| The motor turns reverse.| Modify the phases of the power cables
 |
operation, the motor runs, but there is no lifting

movement

| Lifting with light load works normally but not with heavy load.| The pressure of the overflow valve can be increased by turning the right knob slightly. The solenoid coil is defective and should be replaced
 | The amount of hydraulic oil is not| Add hydraulic oil.
 | enough.
When the «DOWN» button is pressed, the lift does not lower| The lowering valve is activated but does not work.| Check the plug and the coil of the down valve, check the nut for tightness. If necessary, replace

The lowering valve is blocked

| Remove the safety relief valve from the oil supply hole in the lower part of the oil cylinder and clean or replace the unit.
The lift lowers very| The hydraulic oil has a high viscosity,| Replace the oil with an oil conforming to the
slowly| is deteriorated or frozen (in Winter).| operating manual.
when subjected|  |
 |
to weight loads in the standard range.| The “antiknock valve”, inside the cylinders, is blocked.| Remove the parachute valve from the oil supply hole at the bottom of the oil cylinder and clean the device or replace

Platform P1 and P2 are misaligned

| The air in the hydraulic circuit has not been completely removed.| Refer to page 17 «Oil Pressure Adjustment».
Oil leakages along the oil pipe or one of its joints.| Check the sealing of the hydraulic circuit, then adjust the pressure and the level of the oil.
 | The oil drain valve does not close properly| Replace the oil drain valve, if necessary, add oil

Noisy lifting and lowering movements

| The lubricant is not enough.| Lubricate all pins and sliding parts (including piston rod) with mechanical oil.
The floor is not well leveled or the base of the lift does not adhere well to the floor.| Adjust the leveling of the floor to properly adhere the lift to the floor.

APPENDICE

HYDRAULIC CONNECTION DIAGRAM:

OIL PIPE CONNECTION DIAGRAM:

LIFTER’S EXPLODED VIEW:

ELECTRICAL DIAGRAM 220v:

ELECTRICAL DIAGRAM 380v:

USER MANUAL – USE AND MAINTENANCE INSTRUCTIONS

QS| Main Switch| AC-23A| 1|
---|---|---|---|---
KM| Counter AC| SC-03/220V| 1|
M| Engine| 380V/220V| 1| Optional
FU| Fuses| 16A| 2~3| Different Voltage
PS| Transformer| 220VAC/24VDC/2A| 1|
IC| Electronic Board| 02-V14.3-20| 1|
HL| Voltage Indicator| 24V| 1|
SBO| Emergency Stop| XB2 BS542| 1|
SB1| UP Button| IDEC| 1|
SB2| DOWN Button| IDEC| 1|
SB3| Lower Limit Switch| IDEC| 1|
BZR| Buzzer| AD16-22SM| 1|
YV1| Flush Valve| 18W-24VDC| 1|
YV2| Valve| 22W-24VDC| 1|
SQ1| Upper Limit Switch| RV-166S-1C25| 1|
SQ2| Lower Limit Switch| RV-166S-1C25| 1|

DECLARATION OF CONFIRMITV

We,
CLAS EQUIPEMENTS Z. A. de la Crouza 73800 Chignin – France

DECLARE THAT,
Under our responsibility, the following products:

• Model: MOBILE SCISSOR LIFT DUAL CYLINDER LOW RAISE 3T
• Type: PE 6000

Is manufactured in conformity with the European Directive:

• 2006/ 42/EC
• EN ISO 12100 :2010
• EN 60204-1:2006/AC:2010
• EN 1493:2010

Philippe Barrault, 20.07.2020

CLAS EQUIPEMENTS

• SAS au capita l de 130 000€, R.C.S Chambery: 409 786 944, N° TVA lntracommunautaire FR 13 409 786 944 Siege social, Z.A de la Crouza – 73800 CHIGNIN – FRANCE
• +33 (0)4 79 72 62 22
• +33 (0)4 79 72 52 86
• contact@clas.com
• www.clas.com.

CLAS Equipements

• ZA de la CROUZA 73800 CHIGNIN FRANCE.
• Tél. +33 (0)4 79 72 62 22
• Fax. +33 (0)4 79 72 52 86

PE 6000M
PONT CISEAUX MOBILE DOUBLE VERIN BASSE LEVEE 3T MOBILE SCISSOR LIFT DUAL CYLINDER LOW RAISE 3T.

• If you need components or parts, please contact the reseller.
• In case of problems, please contact your authorized technician.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>