SW-MOTECH BC.HTA.20.682.20000 Side Bag Instruction Manual
- June 4, 2024
- SW-MOTECH
Table of Contents
SW-MOTECH BC.HTA.20.682.20000 Side Bag
Thank you for choosing this premium product from SW-MOTECH.
Please carefully read and understand all instructions, safety messages and
warnings in this mounting instruction prior to installation and use of this
product to avoid injury.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Visit our webshop for additional information, such as
application charts and PDF mounting instructions. Any other documents that may
bee required le.g. ABE certifications), are also available for download at our
webshop. Keep these mounting instructions as reference.
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
SAFETY ALERT SYMBOL
This safety alert symbol is used throughout these mounting instructions to
warn of the possibility of death, bodily injury or other warnings. The words
DANGER, WARNING and CAUTION are used with this safety alert symbol to convey
important safety messages and information related to the installation and use
of this product. These words along with the safety alert symbol mean:
DANGER: Indicates a hazardous situation that, if not avoided, will result in
death or serious injury!
WARNING: Indicates a hazardous situation that, if not avoided, could result in
death or serious injury!
CAUTION: Indicates a hazardous situation that, if not avoided, could result in
minor or moderate injury!
NOTICE: Important information, but not death or injury related (property
damage only)!
WARNING: The installation and/or maintenance of this product requires advanced
mechanical skills, the proper tools, and a thorough understanding of tool use
and torque specifications.
For your own safety, sW-MOTECH recommends having installation and/or
maintenance carried out by a qualified and certified motorcycle mechanic.
WARNING: Should you choose to self-install this product, carefully and
completely read allintallation and safety instructions before installation and
use, and follow all the directions and safety precautions given in the
mounting instructions to avoid serious injury or death. Also pay attention to
all relevant information in the vehicle manual during intallation and use
IF YOU DO NOT UNDERSTAND ANY PART OF THESE INSTRUCTIONS OR NEED CLARIFICATION
OF ANY INSTRUCTION, DO NOT ATTEMT TO MOUNT THIS PRODUCT WITHOUT cONTACTING SW-
MOTECH FOR ASSISTANCE.
PREPARATION: Read the mounting instructions carefully and make sure that all
items of the parts list are included.
CAUTION: Make sure that your vehicle is parked safely and cannot fall over. Turn off the engine and remove the 1gnition key. Let the engine/exhaust cool off if necessary. Disconnect the vehicle battery when working on the electrical system. Use appropriate tools and wear always safety glasses and hand protection. Have another person help you.
MOUNTING: All parts and connections removed from the vehicle must be reinstalled in accordance with the vehicle manufacturer specifications or replaced by parts and hardware delivered by SW-MOTECH.
WARNING : Secure all threads, unless otherwise specified, with a medium- strong strength liquid thread locker. Torque specifications undefined by
SW-MOTECH must be obtained from the vehicle manufacturer or by a certified motorcycle workshop!
FUNCTION CHECK: After installation also make sure that no moving parts are obstructed, and function of the vehicle is not hindered in any way. Cables and hoses must not rub and/or be pinched.
WARNING: Before starting to ride, perform a comprehensive check of all functions. After the first 50 km and then at regular intervals, check the tightening torque of all connections and the proper fit of the product. Installed accessories can change driving behavior/stability of the vehicle.
PARTS LIST
Note: All measurements in millimeters. ” The second number indicates the total
quantity of the part in the delivery.
No torque specifications: Use the torque defined by vehicle manufacturer! The
standard torque in this table can be used as long as it is within the vehicle
manufacturer’s specifications.
Mounting
WARNING: Always wear eye and hand protection!
WARNING: Always use appropriate tools!
WARNING: Do not remove the screws on both sides of the vehicle at the
same time!
Support the vehicle with a suitable jack to relieve the rear wheel when the
screw of the suspension strut is loosened.
Remove the upper screws and for mounting on the left side also the shown screw
of the suspension strut.
left side
Inser the rubber damper (2J into the shown opening of the spacer bracket (1).
Attach the stopper spacer (3) to the spacer bracket (1), as shown in the
drawing.
WARNING: Use liquid thread locker!
Tighten the screw as specified.
Then insert the plastic plug (6) into the opening of the stopper spacer (3)
Attach the spacer bracket (1) and nthe side carrier bracket [7) to the left side of the vehicle.
WARNING: Use liquid thread locker!
Tighten the screws (8) as specified.
Tighten the screw [11) with the manufacturers specified torque.
Attach the stopper spacer l14) as shown to the side carrier bracket (13).
WARNING: Use liquid thread locker!
Tighten the screw as specified.
Then insert the plastic plug (16), as shown.
Mount the side carrier bracket (13) to the vehicle as shown.
WARNING: Use liquid thread locker!
Tighten the screws as specified.
Remove the upper screws on the right side of the vehicle.
Attach the countersunk part (21) to the side carrier bracket (20), as shown in the drawing.
WARNING: Use liquid thread locker!
Tighten the screw (22) as specified.
Attach the side carrier bracket (20) on the right side to the vehicle.
WARNING: Use liquid thread locker!
Tighten the screws (25] as specified.
PRODUCT SPECIFIC INFORMATION
WARNING: It is essential to observe the country-specific regulations
regarding the lighting equipment (reflectors]!
If the reflectors mounted to the vehicle in the factory setting are covered by
the side carriers, the reflectors must be removed and/or attached elsewhere in
the same mounting position!
NOTICE: Observe the country-specific regulations concerning vehicle registration/operation as well as TUV regulations if applicable. If required, register installed parts in the vehicle documents through an appropriate inspection authorit.
Thank you for choosing this premium product from SW-MOTECH.
Please visit our webshop for additional information, such as application
charts and PDF mounting instructions. Any other documents that may be required
le.g. ABE certifications), are also available for download at our webshop.
Installation and/or maintenance of this product require good technical
understanding! For your own safety SW-MOTECH recommends having
installation and/or servicing carried out by a specialist workshop!
SW-MOTECH assumes no liability for damage caused by improper installation
and/or maintenance work!
Carefully follow all the directions given in the mounting instructions and pay
attention to all relevant information in the vehicle manual during assembly.
Nonconformance can lead to vehicle damage or even endanger the driver!
These mounting instructions are written based on our current state of
knowledge. Legal requirements for accuracy do not exist.
This product was developed for vehicles in their factory setting.
Compatibility with original accessory parts or other manufacturers’ accessory
parts is not guaranteed. Furthermore, BEFORE installing this product, make
sure that all moving parts le.g. the chain) are in the original state of
maintenance.
Installed accessories can change the driving behaviour and/or stability of
your vehicle.
GENERAL INFORMATION
Observe the country-specific regulations concerning vehicle
registration/operation as well as TUV regulations if applicable. If required,
register installed
parts in the vehicle documents through an appropriate inspection authority.
PREPARATION: Read the mounting instructions carefully and make sure that all
items of the parts list are included. Make sure that your vehicle is parked
safely and cannot fall over. Turn off the engine and remove the ignition key.
Let the motor / exhaust cool off if necessary. Disconnect the vehicle battery
when working on the electrical system. Use appropriate tools. Have another
person to help you.
FUNCTION CHECK: This is a universal product. For this reason make sure
BEFORE the first use, that the product can be fixed properly and used without
problems with your vehicle type. Atter fixation also make sure that no moving
parts are obstructed and the function of the vehicle is not hindered in any
way.
Lamps as taillight and turn signals must not be limited in their function.
Cables and hoses must not rub and/or be pinched. Before starting to ride,
perform a comprehensive check of all functions.
PRODUCT SPECIFIC INFORMATION
ATTENTION: Riding with this product may affect the motorcycles driving and braking performance!
ATTENTION: Before riding and at each stop (every 200 km) check proper fixation of the product!
ATTENTION: The maximum load must not be exceeded! The maximum vehicle load specified by the manufacturer must not be exceeded!
ATTENTION
NOT FOR OFFROAD-USE!
SW-MOTECH GmbH & Co. KG
Ernteweg 7-10 35282 Rauschenberg Germany
Tel./phone +49 (016425/8168 – 050
Fax/fax + 49 (0]6425/8168 10
inforasw-motech.com www.sw-
motech.com
PARTS LIST & CARE
CARE
Clean the product periodically or after each trip, as dust and dirt have a
wear effect and permanent stains can be prevented. Clean the product after
riding in salty conditions, to avoid damage from salt.
First remove dust and encrustations with a soft dry brush, Remove stubborn
deposits with a soft cloth and warm soapy water. Do NOT use strong cleaning
agents, rough cleaning tools or high pressure washer! Then rinse with clear
water.
Before re-use dry the product for at least 24 hours in the air (not in direct
sunlight).
FIXATION
Assemble the components as shown in the drawing.
Pay attention to the side-specific alignment of the bolt, as emphasized in the
schematic drawing.
ATTENTION: Use liquid threat locker!
Tighten the screw as specified.
Loop the string as shown.
HINWEIS: Der Schlosssatz
BC.LOC.00.682.1000:() ist separat
Hang the bag (1) into the sockets of the mounting bracket attached to your
vehicle.
Pay attention that both retaining elements are completely hooked into the
socket contours of the mounting bracket.
Secure the bag (1) with the quick turn fastener (3), by inserting it into the
opening and turning it clockwise.
Pay attention to the audible clicking sound.
The inserting position of the quick turn fastener differs depending on the
vehicles’ side.
Attach the string of the quick turn fastener to the loop on the inside of the
bag.
ATTENTION: Before each ride, lock the lid of the bag.
Thoroughly clean the front of the lid from grease and dirt.
Attach the reflector (4) to the lid as shown in the drawing.
MOUNTING INSTRUCTIONS
Art.-Nr./ Item No.: BC.LOC.O0.682.10000/SRevision: 00 01 2019
Legend Gear Schloss-Satz
Legend Gear lock set
Errors and omissions excepted. Technical and design modifications are subject to change.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>