profi-pumpe ABP011348J Professional Airbrush Gun Instruction Manual

: June 12, 2024
: profi-Pumpe

profi-pumpe ABP011348J Professional Airbrush Gun

profi-pumpe ABP011348J Professional Airbrush Gun

Models

Airbrush-Gun Gravity-Ergo 1035 D 0.38
0.38mm Gravity Feed Airbrush Gun / Gravity, dual-action gun, incl. 9ml paint container
(ABP011348J)
Airbrush Gun Gravity Special 1035 D 0.3
0.3mm Gravity Feed Airbrush Gun / Gravity, dual-action gun, incl. 7ml paint container
(ABP011350J)
Airbrush Gun Gravity Trigger 1035 SD 0.3
0.3mm Gravity Feed Airbrush Gun / Gravity, Semi Dual Action Gun and Gun trigger control, incl. 5ml and 13ml paint container
(ABP011349J)

SAFETY INSTRUCTION AND WARNINGS

Please read the user manual before using the airbrush gun

General remark

INTRODUCTION

We would like to congratulate you on the purchase of your airbrush gun. We appreciate your trust. That‘s why functional security and operational safety stands on first place for us.

To prevent damage to persons or property, you should read this user manual carefully. Please observe all safety precautions and instructions for proper use of the airbrush components. Failure to follow the instructions and safety precautions can result in injury or property damage. Please keep this manual with the instructions and safety instructions carefully in order to at any time you can restore them.

IN GENERAL

The airbrush guns are developed according to the newest stand of technology, manufactured with much care and go under strict intensive controls.
Make sure after unpacking that the data given on the type label match with the included operating instructions. In the case of doubt is not to be used. Transport damages are immediately to be reported to the package distributor on the shipping invoice and to us in written form.

RANGES OF APPLICATION

Airbrush guns can be used in:

Bodypainting
Fingernail painting
Cosmetic
Craftwork spraying
And much more
It can be also used for providing air source for medical, environment protect, breed aquatics Industrial, food Industrial, chemical industrial, laboratory and so on.

Important note: please pay attention before commissioning the airbrush!

The air hoses for airbrush guns are air-tight. Sealing of the screw connections can be carried out with Teflon tape. The rubber seals are to be checked regularly and replaced if necessary.
Connect the air hose, the airbrush gun to the 1/8„ port on the compressor fitting. In order to avoid leaks, the screw connection of the air hose should always be sealed with Teflon tape.
Before starting up, especially after cleaning or after repairs, check the tightness of all connecting elements as well as the tightness of the unit and the hoses..
Please, note that in dependence of the device used (compressor/gun) the color must be diluted.
Your air brush gun must be cleaned thoroughly after each color change, otherwise the residual color mixes with the newly filled color. Moreover, the very fine nozzle will be clogged by dried ink. The gun should be cleaned with thinner and water. Especially the nozzles, which are subject to wear, will have longer lifetime by careful cleaning .
Please, inform yourself in the literature or on the Internet about the working methods and techniques before starting work .
Please, check the function of the gun with clean water. Is the function correctly given, the technology of the gun is perfect.
Please connect compressor, hose and gun always tight. Avoid oscillating opening (constant on and off) of the compressor in order to reduce wear and to save energy.
We sell only tested products. These are strictly for personal use.
Claims for damages for improper disassembly and cleaning can not be accepted.
Complaints about contaminated airbrush guns with paint, residues, could not be recognized.

HOW IT WORKS

The airbrush gun is a two-stage atomizer according to the principle of a jet pump using compressed air as a propellant. With the airbrush gun, any liquid paint with fine pigment, suitable for airbrush guns, can be applied to all substrates, depending on the nozzle size. Acrylic paints, watercolor paints, textile paints and dilute oil paints are easy to apply. The working pressure is usually between 1.5 and 3 bar. The higher the pressure is set, the finer the ink is atomized. In order to deliberately create uneven surfaces, e.g. In order to display sand, one can set the pressure very deliberately very low.
Dual-Action Gun: With one lever, the amount of air as well as the amount of paint can be regulated at the same time.1,2
Semi-Dual-Action: Separate airflow and color control in two areas. Activation via pressure point.3

How It Works

COMMISSIONING

Connect the airbrush gun to the pressure hose (illustrations as an example and depending on airbrush model).

Commissioning

Then screw the air hose with airbrush gun to a suitable compressor. (Illustrations as an example and depending on the compressor model).

Commissioning

Fill the container of the airbrush gun with an appropriately diluted color.

CLEANING AND CARE

Rinse the gun‘s paint dispensers with water or thinner, depending on the paint used.
Clean the air nozzle with a brush or a brush. Do not immerse the nozzle in thinner.
To clean the nozzles, use only the appropriate cleaning needles. Under no circumstances try to clean clogged openings with improper objects, since even the slightest damage can cause a change in the spray performance.

Your airbrush gun must be thoroughly cleaned after every color change. The gun should be regularly cleaned, depending on the paint used, with a suitable thinner, AEROCLEAN RAPID from Schmincke (available in the profi-airbrush-shop) or water.

Especially the nozzles, which are subject to wear, remain functional by careful cleaning longer.

MAINTENANCE

The maintenance and servicing work must be carried out according to our operating instructions, the corresponding safety regulations must be observed.

The airbrush has to be cleaned IMMEDIATELY after use with suitable solvents and dry with compressed air. No deposits may form in the gun. In the presence of any external deposits in the airbrush gun and a damage picture, which can be attributed to it, the claim for legal warranty does not apply.

Change the nozzle set
Always change the complete nozzle set if you want to change the nozzle size. These parts, consisting of nozzle and color needle, are supplied as a complete set. Mount the ink nozzle before inserting the color needle.

The following checks should be carried out regularly:

Clean guide lines (e.g., no bend)
Check for leaks

SAFETY INSTRUCTIONS

Keep away from children! It‘s not a toy!
The airbrush gun must not be operated by persons under the influence of alcohol, drugs or medication.
It is NOT recommended to carry out any technical modifications on your own. Firstly, it is not ensured whether this modification is technically flawless, in addition, the guarantee claim is forfeited.
Observe the ambient temperature between +5 and + 40 ° C
Never pull the hose
Never expose the appliance to dust, acid, vapors, explosive or combustible gases or atmospheric agents (rain, sun, fog, snow).
Avoid cross-sectional constriction in the hose or cable
The airbrush gun must not be used if it is damaged.

The manufacturer declares,

No responsibility in the case of accidents or damages resulting from negligence or disregard of the instructions in this manual
Reject any responsibility for damage resulting from improper use of the equipment

GUARANTEE REGULATIONS / STATUTORY WARRANTY

The statutory guarantee (new and unused goods) exists for all manufacturing and material defects. In such cases we accept the exchange or repair of the airbrush gun.
Shipping costs and consequential damages are borne by us only insofar as we are legally obliged to do so. We provide our services in Germany. Return costs from abroad can only be accepted insofar as we are legally obliged to do so in Germany (or as far as EU law is applicable in Germany).

The warranty does not apply to:

Material wear (e.g., gaskets)
Unjustified interventions or changes in the airbrush gun
Damages by self fault
Improper servicing and improper use
Moreover, we give no damage compensation for secondary damages!

RECOGNISING AND REPAIRING OF MISTAKES

Problem	Possible cause	Solution
Color drips from the nozzle	An particle between the nozzle and the
needle prevents a seal	Remove color needle and nozzle and clean or use new

nozzle set
Color passes from the color needle to the needle seal| Self-tensioning needle seal damaged or absent| Replace needle seal
The spray pattern is crescent-shaped| Air holes or air circulation clogged| Dilute in thinner, then clean with nozzle cleaning needles
The spray pattern is drop / oval shaped| Dirt on the nozzle cup or the air outlet| Rotate the air nozzle 180 ° if the pattern does not change, clean the nozzle cup and the air guide
Uneven, stuttering color beam| Too little paint in the container Color nozzle not attached Self-adjusting needle seal Nozzles dirty or damaged| Top up color Tighten the parts
If necessary, clean or replace the parts
Color bubbles in color cup| Atomizing air flows through the Color channel to the color cup. The paint nozzle is not enough attracted Nozzle is not completely screwed on, air circuit blocked or the seat and Nozzle insert is damaged or defective| Tighten the parts
If necessary, clean or replace the parts

EU DECLARATION OF CONFORMITY

The undersigned, Amur S.à r.l., 36, Rue de la Gare, L-5540 Remich, certifies that the product named overleaf, namely Airbrushpistole (Airbrush-Gun) Gravity-Ergo 1035 D 0.38, Gravity-Special 1035 D 0.3,
Gravity-Trigger 1035 SD 0.3 as placed on the market, complies with the relevant provisions listed below, the relevant EU harmonized directives and the EU standard for safety. This declaration of conformity applies insofar as no modifications are made to the product. The sole responsibility for issuing this declaration of conformity lies with the manufacturer.

The sole authorised person to keep the technical documents:
Amur S.à r.l. – 36, Rue de la Gare – L-5540 Remich
Signed for and on behalf of:
Signature

Airbrush-Gun Gravity-Ergo 1035 D 0.38

Parts list

Needle Cap
Nozzle Cap
Nozzle
O-Ring for Nozzle
Needle
O-Ring for Needle Guide
Needle Guide
Lid for Color Cup
Operation Lever
Lever Guide
Needle Chucking Guide
O-Ring for Handle
Spring
Spring Case
Needle Chucking Nut
Standard-Handle Adjusting
Adjusting Screw
O-Ring for Screw
Lever O-Ring
Valve O-Ring
Valve Body
Valve Rod O-Ring
Valve Rod
Valve Spring
Valve Screws
Nozzle wrench

Airbrush-Gun Gravity-Special 1035 D 0.3

Parts list

Needle Cap
Nozzle Cap
Nozzle
0-Ring for Nozzle
0-Ring for Nozzle Cap
Lid for Col or Cup
Operation Lever
Lever Guide
0-Ring for Needle Guide
Needle Guide
Needle Chucking Guide
Spring
Spring Case
0-Ring for Handle
Needle Chucking Nut
0-Ring for Adjusting Screw
Adjusting Screw
Standard-Handle Adjusting
Lever 0-Ring
Valve 0-Ring
Valve Rod 0-Ring
Valve Rod
Valve Spring
Valve Screw
Valve Body
Hose Connector Nut
0-Ring for Hose Connector
Hose Connector
Needle

Airbrush-Gun Gravity-Trigger 1035 SD 0.3

Air range The first section allows you to regulate the air flow. No color is added.
Color range The second area is used to control the color feed.
Noticeable pressure point

Parts list

Needle Cap
Nozzle Cap
Nozzle
O-Ring for Nozzle
O-Ring for Nozzle Cap
Trigger Fixing Shaft
Lever Handle
Airbrush body
O-Ring for Needle Guide
Needle Guide
Slippery Valve
Spring
Stopper
Guide Screw
Needle Chucking Guide
Spring
Spring Case
Needle Chucking Nut
Standard-Handle Adjusting
O-Ring for Adjusting Screw
Adjusting Screw
O-Ring for Lever Guide
Shaft
Nut
O-Ring for Valve Rod
Valve Seat
O-Ring for Valve
Valve Core
Valve Spring
Valve Body
Handle
Valve Screw
2.5cc Cup
10cc Cup
O-Ring for Cup
Lid for Cup
Needle

TECHNICAL DATA

Problem	Possible cause	Solution
Color drips from the nozzle	An particle between the nozzle and the
needle prevents a seal	Remove color needle and nozzle and clean or use new

nozzle set
Color passes from the color needle to the needle seal| Self-tensioning needle seal damaged or absent| Replace needle seal
The spray pattern is crescent-shaped| ****

Air holes or air circulation clogged

| Dilute in thinner, then clean with nozzle cleaning needles
The spray pattern is drop / oval shaped| Dirt on the nozzle cup or the air outlet| Rotate the air nozzle 180 ° if the pattern does not change, clean the nozzle cup and the air guide
Uneven, stuttering color beam| Too little paint in the container Color nozzle not attached Self-adjusting needle seal Nozzles dirty or damaged| Top up color Tighten the parts
If necessary, clean or replace the parts
Color bubbles in color cup| Atomizing air flows through the Color channel to the color cup.
The paint nozzle is not enough attracted Nozzle is not completely screwed on, air circuit blocked or the seat and Nozzle insert is damaged or defective| Tighten the parts
If necessary, clean or replace the parts