LOREX W452AJ Series 2K Wired Floodlight Security Camera Instructions
- June 9, 2024
- Lorex
Table of Contents
LOREX W452AJ Series 2K Wired Floodlight Security Camera Instructions
Package Contents
Tools Needed
- Drill
- Screwdriver
Overview
- LED Panel
- IR Light
- Camera
- Microphone
- Speaker
- Status Indicator
- MicroSD Card Slot
- Reset Button*
- Mounting Bracket
- Floodlight Housing
- Security Screw
- QR Code
- PIR Sensor
Status Indicator
*Press and hold the reset button until you hear the audio prompts.
Device App Setup
- Download Lorex Home app.https://app.lorex.com/home/download
- Tap + in the app, and then follow the in-app steps to add your floodlight.
⚠ WARNING
TURN OFF THE POWER RUNNING TO YOUR FLOODLIGHT CIRCUIT AT THE BREAKER
If you do not know where your breaker is or how to turn off power, consult a licensed electrician.
Make sure the supply voltage is correct. 100-240 VAC 50/60Hz is required.
DO NOT connect the floodlight to a dimmer or timer.
If you are not replacing a light fixture, you will need to run power cabling
to the install location, and purchase a UL listed junction box for a licensed
electrician to install.
Mounting Setup
-
Remove the existing light fixture and bracket from the wall, and then disconnect the wires.
-
Run the existing wires through the middle of the Mounting Plate.
-
Install the Mounting Plate to a Junction Box OR a wall.
To a Junction Box (recommended) -
Secure the Mounting Plate to the Junction Box using the included Junction Box screws.
To a Wall -
Place and align the Mounting Plate with the arrow up.
-
Use the Mounting Plate as a template to mark 3 holes in a triangular pattern.
-
Use a 1/4” (6mm) drill bit to drill in the marked holes.
-
Use the supplied Mounting screws to secure the Plate to the wall.
⚠ WARNING
PROPERLY GROUND FIXTURE
*Power wire colors in your home may be different. In such a case, consult a licensed electrician.
Wiring & Installation
-
Use the Wire Caps to connect the wires.
a. Twist the Ground wire (green) to the ground wire.
b. Twist the Live wire (black) to the live wire.
c. Twist the Neutral wire (white) to the neutral wire. -
Carefully, fit the wires into the back of the Mounting Bracket.
-
Slide the O-Rings onto the Machine Screws or Short Machine Screws depending on which length works best, and then use a Phillips-head screwdriver to secure the Mounting Bracket to the Plate.
-
Turn the Mounting Bracket completely counter-clockwise, until the Security Screw is pointing down.
-
Take the floodlight, align the two prongs to the grooves on the inner sides, and then push into place.
-
Ensure the floodlight is fully inserted into the Mounting Bracket and that the arrow aligns with the symbol.
-
Use both hands to twist the Mounting Bracket clockwise until the arrow aligns with the symbol.
-
Adjust the camera and LED Panels to the desired position by loosening / tightening the screws on the LED panel arms and the camera.
-
Tighten the pre-installed locking screw at the bottom of the Mounting Bracket.
-
Turn the power ON at the breaker. If the status indicator does not turn on, check that the wiring is correct.
Need help?
For the Quick Start Guide and additional support material, scan the below QR code or visit:
Register your product
Please see our full Terms of Service and Limited Hardware Warranty Policy
at: lorex.com/pages/warranty
Copyright © 2022 Lorex Technology Inc
As our products are subject to continuous improvement, Lorex reserves the
right to modify product design, specifications and prices, without notice and
without incurring any obligation. E&OE. All rights reserved.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>