ELKOep RFGB-20 Wireless Switch Instruction Manual
- June 4, 2024
- ELKOep
Table of Contents
ELKOep RFGB-20 Wireless Switch
Package
- Glass touch controller – 2 buttons, SHARP RFGB-20/W, RFGB-20/B Glass touch controller – 4 buttons, SHARP RFGB-40/W, RFGB-40/B
- Glass touch controller – 2 buttons, ROUND RFGB-220/W, RFGB-220/B Glass touch controller – 4 buttons, ROUND RFGB-240/W, RFGB-240/B
Switch unit, 1-channel RFSAI-11B-SL
EAN 8595188182928 (Glass touch controller – 4 buttons, WHITE SHARP + 1 switch unit, 1-channel) EAN 8595188182942 (Glass touch controller – 4 buttons, WHITE ROUND + 1 switch unit, 1-channel) EAN 8595188182959 (Glass touch controller – 4 buttons, WHITE SHARP + 2 switch units, 1-channel) EAN 8595188182973 (Glass touch controller – 4 buttons, WHITE ROUND + 2 switch units, 1-channel) EAN 8595188182898 (Glass touch controller – 4 buttons, BLACK SHARP + 1 switch unit, 1-channel) EAN 8595188182935 (Glass touch controller – 4 buttons, BLACK ROUND + 1 switch unit, 1-channel) EAN 8595188182904 (Glass touch controller – 4 buttons, BLACK SHARP + 2 switch units, 1-channel) EAN 8595188182966 (Glass touch controller – 4 buttons, BLACK ROUND + 2 switch units, 1-channel)
Schema
The individual elements in the iNELS kit are paired and their functions are
preset.
iNELS kit wireless switch enables the basic function of controlling electrical
appliances – ON / OFF.
Glass touch controller, SHARP / ROUND – 2,4 buttons
RFGB-20/W – Glass touch controller – 2 buttons, WHITE SHARP RFGB-220/W – Glass touch controller – 2 buttons, WHITE ROUND RFGB-40/W – Glass touch controller – 4 buttons, WHITE SHARP RFGB-240/W – Glass touch controller – 4 buttons, WHITE ROUND RFGB-20/B – Glass touch controller – 2 buttons, BLACK SHARP RFGB-220/B – Glass touch controller – 2 buttons, BLACK ROUND RFGB-40/B – Glass touch controller – 4 buttons, BLACK SHARP RFGB-240/B – Glass touch controller – 4 buttons, BLACK ROUND
Characteristics
- The wireless control – used to control, lights, gate, garage door, shutters, etc.
- Thickness only 8 mm.
- 2/4 capacitive buttons allows you to control 2/4 components.
- Fast installation on any surface – the rear base allows screwing to the walls, gluing with doublesided tape or just laying on the table
Replacement of a battery in 3 steps
Assembly
Adhesive 
In the installation box or on the wall
Technical parameters
| Power voltage: | 2x 3 V battery CR 2032 |
|---|---|
| Battery life: | about 2 years depending on the frequency of use |
| Transmission indication | Red LED |
| Number of capacitive buttons: | 2 |
| Communication Protocol: | RFIO2 |
| Frequency: | 868,5 MHz |
| Signal transmission method: | one-way addressed message |
| Range: | in the open up to 200 m |
| Material: | Glass |
Other data
Operating Temperature:| -10 … +50 °C (14 … 122 °F)
Working Position| any
Mounting:| adhesive, screw
Protection| IP20
Pollution degree:| 2
Dimension:| SHARP 94 x 94 x 8 mm (3.7“ x 3.7“x 0.3“)
ROUND 100 x 100 x 8 mm (3.9“ x 3.9“ x 0.3“)
Weight:| SHARP 107 g/ ROUND 108 g
Related standards:| EN 60669, EN 300 220, EN 301 489,
NVč. 426/2000Sb
Switch unit, 1-channel RFSAI-11B-SL
Characteristics
- The switching unit with 1 output channel is used to control appliances, lights, etc.
- The BOX design lets you mount it right in an installation box, a ceiling or a controlled appliance cover.
- The switched load up to 8A (2.000 W).
- Single-function design – switch on/off .
- The output on the switching unit can be controlled by up to 25 channels (1 channel represents one button on the controller).
- The programming button on the unit is also used for manual control of the output.
- Memory status can be pre-set in the event of a power failure.
- For components labeled as iNELS RF Control2 (RFIO2), it is possible to set the repeater function via the RFAF/USB service device.
- Communication frequency with bidirectional protocol iNELS RF Control2 (RFIO2)
Installation options
Technical parameters
| Supply voltage: | 230 V AC |
|---|---|
| Supply voltage frequency: | 50-60 Hz |
| Power apparent / dissipated: | 7 VA / cos φ = 0.1 / 0.7 W |
Output:
Number of contacts:| 1x switching contacts (AgSnO2)
Rated current: / switching power| 8 A / AC1 / 2000 VA
Peak current:| 10 A / <3 s
Max. switching voltage:| 250 V AC1
Communation:
Manual:| button PROG (ON/OFF)
Frequency:| 868.5 MHz
Other data:
Operating temperature:| -15 … + 50 °C (5 … 122 °F)
Mounting:| free at lead-in wires
Protection:| IP40
Overvoltage category:| III.
Dimensions:| 43 x 44 x 22 mm (1.9“ x 1.97“ x 0.8“)
Weight:| 31 g
Related standards:| EN 60730, EN 63044, EN 300 220, EN 301 489
Compatibility
The device can be combined with devices of iNELS RF Control2 with RFIO2 protocol.
Connection
- S – external input
- N – neutral wire
- L – phase wire
- V – output
The screw-less terminal
Radiofrequency signal penetration through various construction materials
Range up to 200 m in open space, if the signal is insuffi cient between the
controller and unit, use the signal repeater RFRP-20 or protocol component
RFIO2 that supports this feature. 
Warning
Instruction manual is designated for mounting and also for the usage of the
device. It is always a part of its pac-king. Installation and connection can
be carried out only by a person with adequate professional qualifi cation with
understanding this instruction manual and functions of the device, and while
observing all valid regulations. Trouble-free function of the device also
depends on transportation, storing and handling. In case you notice any sign
of damage, deformation, malfunction or missing part, do not install this
device and return it to its seller. It is necessary to treat this product and
its parts as electronic waste after its lifetime is terminated. Before
starting installation, make sure that all wires, connected parts or terminals
are de-energized. While mounting and servicing observe safety regulations,
norms, directives and professional, and export regulations for working with
electrical devices. Do not touch parts of the device that are energized – life
threat. Due to transmissivity of RF signal, observe correct location of RF
components in a building where the installation is taking place. RF Control is
designated only for mounting in interiors. Devices are not designated for
installation into exteriors and humid spaces. The must not be installed into
metal switchboards and into plastic switchboards with metal door –
transmissivity of RF signal is then impossible. RF Control is not recommended
for pulleys etc. – radio-frequency signal can be shielded by an obstruction,
interfered, battery of the transceiver can get fl at etc. and thus disable
remote control. 
Designed & Manufactured by:
ELKO EP, s.r.o. Palackého 493, 769 01 Holešov, Všetuly, Czech republic,
www.elkoep.com, Hotline: +420 800 100 671
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>