ELKOep 8302 Wireless Light Dimmer Instruction Manual
- October 27, 2023
- ELKOep
Table of Contents
WIRELESS LIGHT DIMMER
(LUXURY VERSION)
Instruction Manual
8302 Wireless Light Dimmer
Combination of iNELS wall-mounted wireless controller and dimmer for regulation of all types of dimmable bulbs and light sources.
Content
| Glass touch controller – 4 buttons, SHARP RFGB-40/W, RFGB-40/B
---|---
| Glass touch controller – 4 buttons, ROUND RFGB-240/W, RFGB-240/B
| Universal dimmer, 1-channel, RFDEL-71B-SL
EAN 8595188183031 (Glass touch controller – 4 buttons, SHARP – white + 1 x
Universal dimmer)
EAN 8595188183079 (Glass touch controller – 4 buttons, SHARP – white + 2 x
Universal dimmer)
EAN 8595188183055 (Glass touch controller – 4 buttons, SHARP – white + 1 x
Universal dimmer)
EAN 8595188183093 (Glass touch controller – 4 buttons, SHARP – white + 2x
Universal dimmer)
EAN 8595188183024 (Glass touch controller – 4 buttons, SHARP – black + 1 x
Universal dimmer)
EAN 8595188183062 (Glass touch controller – 4 buttons, SHARP – black + 2 x
Universal dimmer)
EAN 8595188183048 (Glass touch controller – 4 buttons, SHARP – black + 1 x
Universal dimmer)
EAN 8595188183086 (Glass touch controller – 4 buttons, SHARP – black + 2x
Universal dimmer)
The individual elements in the iNELS set are paired and their functions are
preset.
iNELS Wireless light dimmer enables dimming of diff erent types of lights or
controlling electrical appliances
The settings of the wall controllers can be changed – detailed manual on the next pages.
Glass touch controller – 4 buttons,
SHARP/ROUND, RFGB-40/RFGB-240
Detailed manual
|
---|---
https://elko.li/rfgb-40| https://elko.li/rfgb-240
Characteristics
- The wireless control – used to control, lights, gate, garage door, shutters, etc.
- Thickness only 8 mm.
- 4 capacitive buttons allow you to control 2/4 components.
- Fast installation on any surface – the rear base allows screwing to the walls, gluing with doublesided tape or just laying on the table
Replacement of a battery in 3 steps
Press to open the plug-in battery holder (you can use a fl at-blade screwdriver to open it)..| Insert the CR2032 battery into Battery holder. Watch out for polarity.| Insert the holder into the device.
Assembly
Adhesive
Peel off one protective layer on the doublesided
adhesive sheets and stick them to the marked places on the controller.| Peel
off the second protective layer on the doublesided adhesive sheets and place
the
control in the prepared place.| If the device is installed on glass, cover it
with
a cover foil
In the installation box or on the wall
Mount the snap bar on the controller into the installation box or on the wall|
Place the mounting jig on the KU box and screw it on| Snap on the controller.
Technical parameters| RFGB-40/RFGB-240
---|---
Power voltage:| 2x 3 V battery CR 2032
Battery life:| about 2 years depending on the frequency of use
Transmission indication| Red LED
Number of capacitive buttons:| 4
Communication Protocol:| RFIO2
Frequency:| 868.5 MHz
Signal transmission method:| one-way addressed message
Range:| in the open up to 200 m
Material:| Glass
Other data
Operating Temperature:| -10 … +50 °C (14 … 122 °F)
Working Position| any
Mounting:| adhesive, screw
Protection| IP20
Pollution degree:| 2
Dimension:| SHARP 94 x 94 x 8 mm (3.7″ x 3.7″x 0.3″)
/ ROUND 100 x 100 x 8 mm (3.9″ x 3.9″ x 0.3″)
Weight:| SHARP 107 g/ ROUND 108 g
Related standards:| EN 60669, EN 300 220, EN 301 489
Universal dimmer, 1-channel
RFDEL-71B-SL
Detailed manual
Characteristics
-
The universal built-in dimmer is used to regulate light sources.
-
They can be combined with detectors, controllers, iNELS RF Control or system components.
-
7 light functions – smooth increase or decrease with time setting 2s-30 min. + additional function
SWITCH OFF -
Thanks to setting the min.brightness you will eliminate fl ashing of the LED and ESL light sources
-
The universal dimmer may be controlled by up to 25 channels (1 channel represents 1 button).
-
Connection of the existing button on the control input “S“ enables combination of wireless control with classic (wired) control.
-
The programming button on the controller is also used for manual control of the output.
-
For components labelled as iNELS RF Control2 (RFIO2 ), it is possible to set the repeater function via the RFAF/USB service device.
-
Range up to 200 m (in open space), if the signal is insuffi cient between the controller and unit, use the signal repeater RFRP-20 or protocol component RFIO2 that support this feature.
Installation option
mounting in an installation box| mounting into the ceiling light cover| Under
ceiling mounted
Technical parametres| RFDEL-71B-SL
---|---
Supply voltage:| 230 V AC / 50 Hz
Apparent power:| 5 VA
Dissipated power:| 0.5 W
Supply voltage tolerance:| +10/ -15 %
Connection:| 4 – wire, with NEUTRAL
Dimmed load: R. L. C. LED. ESL
Output:
Contactless:| 2 x MOSFET
Load capacity:| 300 W ‘
Control:
RF command from the transmitter:| 868.5 MHz
Range in open space: up to 200 m
Manual control:| button PROG (ON/OFF), external button
Other data:
Operating temperature: -15 … + 45 °C
Storage temperature:| -30 … +70°C
Operating position:| any
Protection:| IP40 under normal conditions
Overvoltage category:| III.
Contamination degree:| 2
Connection:| screwless terminals
Connecting conductor:| 0.2-1.5 mm2
Dimensions:| 43 x 44 x 22 mm
Weight:| 30 g
Related standards:| EN 60730, EN 63044. EN 300 220. EN 301 489
Compatibility
The device can be combined with all system components, controls and devices of
iNELS RF Control and iNELS RF Control2.
The detector can be assigned an iNELS RF Control2 (RFIO2 ) communication
protocol. Connection
Radiofrequency signal penetration through various construction materials
Range up to 200 m in open space, if the signal is insuffi cient between the
controller and unit, use the signal repeater RFRP-20 or protocol component
RFIO² that supports this feature.
|
---|---
60 – 90 %
brick walls| 80 – 95 %
wooden structures with plaster boards
|
20 – 60 %
reinforced concrete| 0 – 10 %
metal partitions
| 80- 90 %
common glass
Warning
Instruction manual is designated for mounting and also for the usage of the
device. It is always a part of its packing.
Installation and connection can be carried out only by a person with adequate
professional qualifi cation with understanding this instruction manual and
functions of the device, and while observing all valid regulations.
Trouble-free function of the device also depends on transportation, storing
and handling. In case you notice any sign of damage, deformation, malfunction
or missing part, do not install this device and return it to its seller.
It is necessary to treat this product and its parts as electronic waste after
its lifetime is terminated.
Before starting installation, make sure that all wires, connected parts or
terminals are de-energized.
While mounting and servicing observe safety regulations, norms, directives and
professional, and export regulations for working with electrical devices. Do
not touch parts of the device that are energized –life threat. Due to
transmissivity of RF signal, observe correct location of RF components in a
building where the installation is taking place.
RF Control is designated only for mounting in interiors. Devices are not
designated for installation into exteriors and humid spaces.
The must not be installed into metal switchboards and into plastic
switchboards with metal door – transmissivity of RF signal is then impossible.
RF Control is not recommended for pulleys etc. –radiofrequency signal can be
shielded by an obstruction, interfered, battery of the transceiver can get fl
at etc. and thus disable remote control.
Notes
Designed & Manufactured by:
ELKO EP, s.r.o. Palackého 493, 769 01 Holešov, Všetuly,
Czech republic, www.elkoep.com, Hotline: +420 800 100
671
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>