ELKOep GPSR-1 GPS Receiver Instruction Manual
- June 12, 2024
- ELKOep
Table of Contents
GPSR-1 GPS Receiver
Instruction Manual
GPSR-1 Receiver GPS
Characteristics
- GPS module, designed for synchronization of switching clock SHT-6.
- Two-wire connection using screwless terminals – no matter the polarity!
- Connection cable length up to 100m.
- Optical indication of module functional states.
- It broadcasts time information in DCF 77 format.
- Setting the time zone of the DIP switch (UTC-12 to UTC+14).
- Choice of one of 40 time zones
- The receiver is only compatible with the new SHT-6G version (EAN:
- 8595188182751) and fi rmware 2.37 or higher
Description
- Connection terminals with SHT-6
- Indication of operating states
- Sync indication
- DIP switches to set the time zone
Installation
- It must be mounted so that there are no obstacles between the GPS receiver and the direction of reception (trees, roofs of buildings, etc.)
- There must not be any transformers, contactor relays, fl uorescent lamps, etc., placed in the immediate vicinity of the GPS receiver (about 1m)
- Do not install GPS receiver near metal objects, el. cables, etc.
Connection with SHT-6
If a shielded cable is used, connect the shield to terminal G.
Technical parameters
GPSR-1
| Connected: | two-wire, it does not depend on polarity |
|---|---|
| Max. voltage on conductors: | DC 10 V |
Other information
| Working temperature: | -20.. +55 °C |
|---|---|
| Storage temperature: | -30.. +70 °C |
| Covers: | IP65 |
| Terminal plate: | screwless clamps |
| Cross-section of connecting conductors: | drat: 0.2 – 0.75 mm²/ cable + core: |
0.25 – 0.34 mm²
About the connection cable:| max. 6.5 mm
Dimension:| 98 x 62 x 34 mm
Weight:| 96 g
Reception area:| whole world
LED indication
| red LED (under cover)| green LED
---|---|---
Failure of internal circuits| | –
Searching for GPS signal| | –
Synchronization time. Information| | –
GPS signal OK
– sending time information| |
Function
GPSR-1 is designed to receive and decode the signal GPS. The correct operation is indicated by the red LED fl ashing at interval 1s.
Warning
Installation and connection should only be carried out by a qualifi ed installer or electrician, who is thoroughly familiar with these instructions and functions of device. Before starting the installation, please make sure that the device is de-energized and the main switch is in the off position. For installation and setting use screw-driver cca 2 mm. The device is fully- electronic – installation should be carried out according to this fact. Non- problematic function depends also on the way of transportation, storing and handling. In case of any signs of destruction, deformation, non-function or missing part, don´t install and claim at your seller it is possible to dismount the device after its lifetime, recycle, or store in protective dump.
Overview of time zones
Set up time zones
| Function| DIP-1| DIP-2| DIP-3| DIP-4| DIP-5|
DIP-6
---|---|---|---|---|---|---|---
0| TEST LED + DIP switches| OFF| OFF| OFF| OFF| OFF| OFF
1| UTC| OFF| OFF| OFF| OFF| OFF| ON
2| UTC+1| OFF| OFF| OFF| OFF| ON| OFF
3| UTC+2| OFF| OFF| OFF| OFF| ON| ON
4| UTC+3| OFF| OFF| OFF| ON| OFF| OFF
5| UTC+3:30| OFF| OFF| OFF| ON| OFF| ON
6| UTC+4| OFF| OFF| OFF| ON| ON| OFF
7| UTC+4:30| OFF| OFF| OFF| ON| ON| ON
8| UTC+5| OFF| OFF| ON| OFF| OFF| OFF
9| UTC+5:30| OFF| OFF| ON| OFF| OFF| ON
10| UTC+5:45| OFF| OFF| ON| OFF| ON| OFF
11| UTC+6| OFF| OFF| ON| OFF| ON| ON
12| UTC+6:30| OFF| OFF| ON| ON| OFF| OFF
13| UTC+7| OFF| OFF| ON| ON| OFF| ON
14| UTC+8| OFF| OFF| ON| ON| ON| OFF
15| UTC+8:45| OFF| OFF| ON| ON| ON| ON
16| UTC+9| OFF| ON| OFF| OFF| OFF| OFF
17| UTC+9:30| OFF| ON| OFF| OFF| OFF| ON
18| UTC+10| OFF| ON| OFF| OFF| ON| OFF
19| UTC+10:30| OFF| ON| OFF| OFF| ON| ON
20| UTC+11| OFF| ON| OFF| ON| OFF| OFF
21| UTC+11:30| OFF| ON| OFF| ON| OFF| ON
22| UTC+12| OFF| ON| OFF| ON| ON| OFF
23| UTC+12:45| OFF| ON| OFF| ON| ON| ON
24| UTC+13| OFF| ON| ON| OFF| OFF| OFF
25| UTC+14| OFF| ON| ON| OFF| OFF| ON
26| UTC-12| OFF| ON| ON| OFF| ON| OFF
27| UTC-11| OFF| ON| ON| OFF| ON| ON
28| UTC-10| OFF| ON| ON| ON| OFF| OFF
29| UTC-9:30| OFF| ON| ON| ON| OFF| ON
30| UTC-9| OFF| ON| ON| ON| ON| OFF
31| UTC-8| OFF| ON| ON| ON| ON| ON
32| UTC-7| ON| OFF| OFF| OFF| OFF| OFF
33| UTC-6| ON| OFF| OFF| OFF| OFF| ON
34| UTC-5| ON| OFF| OFF| OFF| ON| OFF
35| UTC-4:30| ON| OFF| OFF| OFF| ON| ON
36| UTC-4| ON| OFF| OFF| ON| OFF| OFF
37| UTC-3:30| ON| OFF| OFF| ON| OFF| ON
38| UTC-3| ON| OFF| OFF| ON| ON| OFF
39| UTC-2| ON| OFF| OFF| ON| ON| ON
40| UTC-1| ON| OFF| ON| OFF| OFF| OFF
41…61| not used| –| –| –| –| –| –
62| TEST communication| ON| ON| ON| ON| ON| OFF
63| TEST LED + DIP switches| ON| ON| ON| ON| ON| ON
ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: +420 573 514 211
e-mail: elko@elkoep.com
www.elkoep.com
Made in Czech Republic
02-1/2022 Rev.: 0
Documents / Resources
|
ELKOep GPSR-1 GPS
Receiver
[pdf] Instruction Manual
GPSR-1 A4 1jaz, GPSR-1 GPS Receiver, GPSR-1, GPS Receiver, Receiver
---|---