GOLDEN LIGHTING 0305-BA2 BLK-CLR Carver 2 Light 20 inch Matte Black Bath Fixture Wall Light Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 0305-BA2 BLK-CLR Carver 2 Light 20 inch Matte Black Bath
Fixture Wall Light Instruction Manual
Dimensions
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
We appreciate your business and hope you love your new light
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment. Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off? Follow us, share a picture, and tag us on Social…
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Mounting strap (B) contains several pairs of threaded
holes. Find the pair of holes that matches the spacing of the holes on the
junction box and the new fixture’s backplate. Two sets of mounting screws (A &
D) should be attached to mounting strap (B). You may need to tighten the nuts
(C) that hold mounting screws (A) in place. 2. Pull the house wires through
the center of mounting strap (B). Place mounting strap (B) over the junction
box so that mounting screws (A) are horizontally level to the floor, and in
alignment with the hole locations on backplate (F). Secure mounting strap (B)
to the junction box with mounting screws (D) and a screwdriver. Tighten the
screws securely.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
3. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
4. Place backplate (F) against mounting strap (B) until mounting screws (A)
protrude from the holes in backplate (F). Tightly thread decorative nuts (G)
onto the exposed threads of mounting screws (A). Twist deco nuts (G) until
backplate (F) is snug against the wall. 5. Hold shades (I) over sockets (H)
and secure in place using socket rings (J). Use the provided tool (K) on
socket rings (J) to finish tightening. 6. Install light bulbs (not provided)
into sockets (H) in accordance with the fixture’s specifications. Do not
exceed the maximum wattage. Your installation is now complete. Turn on the
power and test the fixture.