GOLDEN LIGHTING 3320-BA3 PW-WHT Lana 3 Light Pewter Bath Fixture Wall Light Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
3320-BA3 PW-WHT Lana 3 Light Pewter Bath Fixture Wall Light
Instruction Manual
3320-BA3 PW-WHT Lana 3 Light Pewter Bath Fixture Wall Light
Thank You for Choosing Golden Lighting for Your Lighting Needs!
For Customer Service, contact the place of purchase to arrange for
replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap.
- Mounting plate (B) contains several pairs of threaded holes. Find the pair of holes that matches the spacing of the holes on the junction box and your fixture’s backplate. Two mounting screws (C) should be attached to mounting plate (B). Small screws (A) may be attached to backplate (G), unscrew small screws (A) and set aside for later.
- Place mounting plate (B) over the junction box. Secure mounting strap (B) to the junction box with mounting screws (C) and a screwdriver. Tighten the screws securely. After you determine the proper placement, hold mounting plate (B) up to the wall and use a pencil to mark the wall through the two circular holes found on mounting plate (B).
- Set aside mounting plate (B) for now. Use a drill bit to create two holes on your pencil marks and insert plastic screw holders/anchors (D) into the holes made until the plastic screw holders/ anchors are flush with the wall. Align mounting plate (B) with the plastic screw holders/anchors (D). Using a drill or screwdriver, insert mounting screws (F) into the plastic screw holders/anchors (D).
- Secure mounting plate (B) to the junction box using mounting screws (C) and a screwdriver. Tighten the screws securely. Pull the house wires through the center of mounting plate (B).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation. Please proceed to the next step.
CONNECTING THE WIRES
-
Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION -
Place the fixture’s backplate (G) over mounting plate (B). Align the holes in backplate (G) with the holes found on mounting plate (B). Insert small screws (A) into the holes found on backplate (G) and mounting plate (B). Tighten screws until backplate (G) is secure to mounting plate (B) and the fixture is snug against the wall.
-
Lift metal shades (I) up to sockets (H) and secure in place using inner shade cover (J) and socket rings (K).
-
Install light bulbs (not included) into sockets (H) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage.
-
Twist iron cages (L) into the inner shade covers (J) in a clockwise manner to secure. Your installation is now complete. Turn on the power and test the fixture.
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure
the best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Assembly Instructions: 3320-BA3
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
GoldenLighting.com
Documents / Resources
|
GOLDEN LIGHTING 3320-BA3 PW-WHT Lana 3 Light Pewter Bath Fixture Wall
Light
[pdf] Instruction Manual
3320-BA3 PW-WHT, 3320-BA3 PW-WHT Lana 3 Light Pewter Bath Fixture Wall Light,
Lana 3 Light Pewter Bath Fixture Wall Light, 3 Light Pewter Bath Fixture Wall
Light, Pewter Bath Fixture Wall Light, Bath Fixture Wall Light, Fixture Wall
Light, Wall Light, Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>