HYUNDAI Ioniq 5 Mudguard Kit Owner’s Manual

June 12, 2024
HYUNDAI

HYUNDAI-LOGO

HYUNDAI Ioniq 5 Mudguard Kit

HYUNDAI-Ioniq-5-Mudguard-Kit-PRODUT

Product Information

  • Vehicle Model: Ioniq 5
  • Accessory: Mudguard Kit
  • Model Year: 2022~
  • Part No.: GIF46 AC100
  • Language: English
  • Revision Date: 10/29/2021

Instructional Symbols / Definitions

  • Denotes warnings that may lead to serious physical injury or vehicle damage

  • Denotes cautions to be taken to avoid physical injury or electronic component damage

  • Denotes cautions to be taken to avoid vehicle and component damage

  • Denotes quality processes to be checked prior to moving to the next step

  • Denotes specific tools that are necessary to complete a step

  • Denotes important information to be reviewed during the step

Denotes personal protective equipment (PPEs) that may be required for a step. Examples of safety equipment icons noted below:

Basic Required Tools

HYUNDAI-Ioniq-5-Mudguard-Kit-FIG-7

Part Weight (Gross)

  • 1.08: lbs
  • 0.49: kg

FMVSS 110 Compliance Information
All dealers must determine if the Net weight they have added in the form of all options or accessories, when added to the weight of all Port/Dealer Installed options or accessories, exceeds the lesser of 1.5% of GVWR or 100 lbs. If the additional weight does exceed the lesser of the indicated thresholds, a “Load Carrying Capacity Reduced” label must be installed. A black, fine-point, indelible marker must be used to write by hand onto the label, the reduced carrying capacity in kilograms or pounds, which is the total weight of all added options and accessories.

Load Label Part Number: NP070 – 09003

Notes to the installer

  1. Read the entire Installation Instructions prior to beginning the installation of the part.
  2. If applicable, scan the barcode label located on the accessory part or packaging prior to installing, to register the part. If this accessory is installed as a replacement, register the removal of the
  3. old part before registering the new part. Old and new parts will have different barcode data, and the old registration cannot be reused. Make sure the vehicle is completely clean and dry in the area(s) the part is to be installed.
  4. Ensure the vehicle is properly protected in the areas) that the accessory is to be installed.
  5. NEVER place tools on painted surfaces, seating surfaces, dash pad, console or floor carpet/mats.
  6. Always wear appropriate personal protective equipment, including gloves, safety glasses, etc., when required.
  7. Mix a 1 to 1 ratio of water and Isopropyl Alcohol (70%) into a spray bottle.

Kit Overview

HYUNDAI-Ioniq-5-Mudguard-Kit-FIG-8

No. Qty Description
1 1 Front Mudguard LH
2 1 Front Mudguard RH
3 1 Rear Mudguard LH
4 1 Rear Mudguard RH
5 1 Hardware Bag
6 1 Front Mudguard Template
--- --- ---

Hardware Kit Contents

HYUNDAI-Ioniq-5-Mudguard-Kit-FIG-9

Hardware Kit Total: 14

INSTALLATION INSTRUCTION

HYUNDAI-Ioniq-5-Mudguard-Kit-FIG-10

  • A. Remove the adhesive backing strip from the provided template and place it on the underside of the driver’s side front wheel arch garnish trim as shown above.
  • B. Using a Center Punch, mark the center of the crosshairs on the template as shown.
  • C. Remove the template and place it in a safe location to be used on the passenger’s side front wheel arch garnish trim.
  • D. Place a Drill Stop 10mm (25/64″) back from the tip of a 3mm (1/8″) Drill Bit and drill a pilot hole at the center punch mark.
  • E. Place a Drill Stop 10mm (25/64″) back from the tip of a 8mm (5/16″) Drill Bit and enlarge the pilot hole.
  • F. Carefully Deburr the drilled hole. Do NOT enlarge the hole.
  • G. Repeat this step on the passenger’s side front wheel arch garnish trim.

WARNING! Take precautions when using the drill to help avoid injury or damage to the vehicle.
Caution! Make sure the drill stop is properly set on the drill bits to ensure the drill bits do not make contact with the steel rocker panel behind the garnish trim.

NOTE: Fully turn the steering wheel to the left when installing the driver’s side front mudguard (LH) and fully turn the steering wheel to the right when installing the passenger’s side front mudguard (RH).

  • A. Starting on the driver’s side front wheel well area, remove the two (2) plastic retainers as shown.
  • B. Discard the removed hardware.
  • C. Clean the area of the lower fender where the mudguard will be positioned as shown, using 50/50 mix of Isopropyl alcohol (70%) & water and allow to fully dry.

WARNING! Ensure all surfaces have fully dried.

  • A. Align the driver’s side front mudguard (LH) as shown ensuring a proper fit.
  • B. Place pieces of making tape along the upper and rear edges of the mudguard as shown above.
  • C. Temporarily remove the mudguard and set aside in a safe location.

Make sure to push the mudguard upward and inward during the installation to eliminate any possible gaps.

  • A. Apply one (1) adhesive promoter onto the lower fender in the highlighted area shown above.
    NOTE : The adhesive promoter should not be applied further than 1.2″ (30.5mm) below the lower fender feature line as shown above.

  • B. Properly discard promoter.

WARNING! Promoter may cause skin irritation if in contact with bare skin. Ensure gloves are properly worn.

A. Peel away approximately 1″ (25mm) of the adhesive tape liner from the front mudguard (LH), then wrap around as shown above.
B. Using a piece of masking tape, secure the tape liner to the outside surface as shown above.

CAUTION: Be careful not to touch or contaminate the exposed surface of the adhesive tape.

A. Align the mudguard (LH) back into position.
B. W hile pushing the mudguard upward and inward as shown, insert one (1) provided plastic retainer into the bottom hole as shown. Make sure to push in the center portion of the plastic retainer to lock the retainer in place.

Make sure to push the mudguard upward and inward during the installation to eliminate any possible gaps.

  • A. While pushing the mudguard upward and inward as shown, insert two (2) provided plastic retainers as shown. Make sure to push in the center portion of the plastic retainers to lock the retainers in place.
  • B. Remove and discard the pieces of masking tape.
  • C. While maintaining proper alignment of the front mudguard (LH) with one hand, carefully remove the adhesive tape liner in a downward direction.
  • D. Repeat steps 1-7 for passenger’s side front mudguard (RH).

Check for any visible gaps. If any gaps exceed 0.5mm, loosen the hardware and refit the mudguard(s) to the body to decrease or eliminate the gaps.

  • A. On the driver’s side rear wheel well area, remove the plastic retainer from the bottom of the vehicle as shown.

  • B. R emove the two (2) screws as shown.

  • C. Discard the removed hardware.

  • A. Align the rear mudguard (LH) as shown ensuring a proper fit.

Make sure to push the mudguard upward and inward during the installation to eliminate any possible gaps.

  • A. While pushing the mudguard upward and inward as shown, insert one (1) provided retainer into the bottom hole as shown. Make sure to push in the center portion of the plastic retainer to lock the retainer in place.

Make sure to push the mudguard upward and inward during the installation to eliminate any possible gaps.

Visual Check

Item to be Checked

  • Make sure to push the Front and Rear Mudguards upward and inward during the installation to eliminate any possible gaps.
    Check for any visible gaps.

  • If any gaps exceed 0.5mm, loosen the mounting hardware and refit the Mudguard(s) to the body to decrease or eliminate the gaps.

  • A. While pushing the mudguard upward and inward as shown, insert and fasten one (1) provided screw into the upper hole “A” as shown.

  • B. Insert and fasten one (1) provided screw into the lower hole “B” as shown.

  • C. Repeat steps 8-11 for the passenger’s side rear mudguard (RH).

  • D. Installation is complete.

Check for any visible gaps. If any gaps exceed 0.5mm, loosen the mounting screws and refit the mudguard(s) to the body to decrease or eliminate the gaps. Be careful not to over-tighten or strip the screw head.

Result

  • Front and Rear Mudguards are properly aligned.
  • Any visible gaps do not exceed 0.5mm.

Vehicle Model: Ioniq 5

Accessory: Mudguard Kit

Note: Difficulty stated above reflects the minimum level of expertise required to install the accessory:

  • (A) Customer
  • (B) Dealer Technician
  • (C) Master Technician or Specialist

Electronic Installation Instructions

If this is a printed copy of the installation instructions, ensure you have the latest revision by scanning the QR code or by entering the website address listed below before beginning installation. Use the latest revision date as noted by “Rev. Date” above.

www.hyundaiaccessories.com/admin_media_uploads/installationSheets/gif46_ac100.pdf

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals