soundmaster UR580 Digital Clock Radio Instruction Manual

UR580 Digital Clock Radio
Instruction Manual

ENVIRONMENTAL PROTECTION

Do not dispose of this product with normal household waste at the end of its life cycle. Return it to a collection point for the recycling of electrical and electronic devices. This is indicated by the symbol on the product, user manual or packaging The materials are reusable according to their markings. By reusing, recycling, or other forms of utilization of old devices you make an important contribution to the protection of our environment.
Please contact your local authorities for details about collection points.
WARNING
Risk of electric shock Does not open!
Caution: To reduce the risk of electric shock, do not remove the cover (or back). There are no user-serviceable parts inside. Refer servicing to qualified service personnel.
This symbol indicates the presence of dangerous voltage inside the enclosure, sufficient enough to cause electric shock.
This symbol indicates the presence of important operating and maintenance instructions for the device
Used batteries are hazardous waste and NOT to be disposed of with household waste! As a consumer you are legally obligated to return all batteries for environmentally responsible recycling – no matter whether or not the batteries contain harmful substances*)
Return batteries free of charge to public collection points in your community or shops selling batteries of the respective kind.
Only return fully discharged batteries
*) marked Cd = cadmium, Hg = mercury, Pb = lead

• Only use mercury and cadmium-free batteries.
• Used batteries are hazardous waste and NOT to be disposed of with household waste!!!
• Keep batteries away from children. Children might swallow batteries.
• Contact a physician immediately if a battery was swallowed.
• Check your batteries regularly to avoid battery leakage.
• Batteries shall not be exposed to excessive heat such as sunshine, fire, or the like.
• CAUTION: Danger of explosion if the battery is incorrectly replaced
• Replace only with the same or equivalent type

WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. Keep new and used batteries away from children. If the battery compartment does not close securely, stop using the product and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. Safety, Environmental and Setup Instructions

• Use the device in dry indoor environments only.
• Protect the device from humidity.
• This apparatus is for moderate climates areas use, not suitable for use in tropical climates countries.
• No objects filled with liquids, such as vases, shall be placed on the apparatus.
• The mains plug or an appliance coupler is used as the disconnect device, the disconnect devices shall remain readily operable.
• Connect this device to a properly installed and earthed wall outlet only. Make sure the mains voltage corresponds with the specifications on the rating plate.
• Make sure the main cable stays dry during operation. Do not pinch or damage the main cable in any way.
• A damaged mains cable or plug must immediately be replaced by an authorized service center.
• In case of lightning, immediately disconnect the device from the main supply.
• Children should be supervised by their parents when using the device.
• Clean the device with a dry cloth only.
• Do NOT use CLEANING AGENTS or ABRASIVE CLOTHS!
• Do not expose the device to direct sunlight or other heat sources.
• Install the device at a location with sufficient ventilation in order to prevent heat accumulation.
• Do not cover the ventilation openings!
• Install the device at a safe and vibration-free location.
• Install the device as far away as possible from computers and microwave units; otherwise, radio reception may be disturbed.
• Do not open or repair the enclosure. It is not safe to do so and will void your warranty. Repairs only by authorized service/ customer center.
• No naked flame sources, such as lighted candles, should be placed on the unit.
• When you necessary to ship the unit store it in its original package. Save the package for this purpose.
• In case of malfunction due to electrostatic discharge or fast transient (burst), remove and reconnect the power supply.
• If the unit is not using for a long period of time, disconnect it from the power supply by unplugging the power plug. This is to avoid the risk of fire.

LOCATION OF CONTROLS

1 Alarm 1 buzzer indicator
2 Alarm 1 radio indicator
3 Alarm 1 vibration pad indicator
4 Sleep timer indicator
5 Alarm 2 buzzer indicator
6 Alarm 2 radio indicator
7 Alarm 2 vibration pad indicator
8 Memory FM
9 USB charging port
10 Down  button
11 Radio volume / Pairing vibration pad
12 Radio on / Sleep / Timer| 13 Time set / Memory radio
14 Radio off / Snooze
15 Alarm set
16 Alarm 1 on/off
17 Alarm 2 on/off
18 Up button
19 Display dimmer
20 Speaker
21 Backup battery compartment
22 DC IN jack
23 FM antenna
---|---

Vibration pad

1. Battery indicator
2. Switch for vibration strength
3. Battery compartment

INSTALLATION

CONTENT OF DELIVERY
➢ Main unit
➢ Vibration pad
➢ AC adaptor
➢ Instruction manual

BACKUP BATTERY

One CR2032 lithium battery (not included) is needed to keep all settings (alarm, time, radio settings) if the power is interrupted.

1. Open the battery compartment at the backside of the unit.
2. Insert the CR2032 battery with the “+” side facing up into the battery compartment.
3. Close the battery compartment.

Note:
➢ The display will turn off if the power is interrupted.
➢ Without power, the unit has no radio and alarm function.

VIBRATION PAD

GET STARTED ON THE VIBRATION PAD

1. Open the battery compartment at the backside of the vibration pad.
2. Insert 3 batteries of type LR03 (“AAA” size) 1.5V into the battery compartment. Please ensure that the polarity is correct (see indicated in the battery compartment).
3. Close the battery compartment.
4. During the LED indicator is flashing at the vibration pad, press in off mode the “PAIR” button on the radio. Now the vibration pad is paired with the unit.

Note: When the battery gets low, the LED indicator of the vibration pad is flashing.
So that the vibration pad stays close to the pillow, put the vibration pad on the cover of your pillow!

BASIC OPERATIONS

RADIO ON / OFF
Press the “RADIO ON” button to turn on the unit in radio mode.
Press the “RADIO OFF” button to turn off the unit.
ADJUSTING VOLUME
In on mode, press the “VOL / RADIO” button. During the display show “LXX” (XX = the level of the volume), and press the “ ” or “ ” button to decrease or increase the volume (L01 = min, L15 = max). It is not possible to mute the radio.
BRIGHTNESS ADJUSTMENT
Rotate the “DISPLAY DIMMER” knob on the right side of the unit to adjust the brightness of the display.

TIME SETTING

1. In off mode, press the “TIME SET” button to enter the time setting. The hour flash in the display.
2. Press the button to adjust the hour setting and press the “TIME SET” button to confirm. The minute flash in the display.
3. Press the button to adjust the minute setting and press the “TIME SET” button to confirm. The display changed to the time format.
4. Press the button to adjust the time format (24Hr or 12Hr) and press the “TIME SET” button to confirm.
5. Now the time is set.

FM
You can store up to 10 radio stations!

1. Press the “RADIO ON” button to turn on the unit in radio mode. The display shows “ON” and after a few seconds the radio frequency. Note: After a few seconds, the unit shows the clock in the display.
2. Press and hold the button to start the automatic search. The radio stops at the next available radio station.
3. Press the button shortly to manually tune the radio in 100kHz steps.
4. During radio mode, press the “RADIO ON” button to show the currently tuned radio frequency.
5. To switch off the radio, press the “RADIO OFF” button.

Store preset station

1. Search the desired radio station
2. Press and hold the “MEMORY RADIO” button until the preset station number flashes in the display.
3. While the display is flashing, select with the button the desired preset station number and press the “MEMORY RADIO” button to confirm.
4. To store further radio stations, repeat steps 1-3.

Recall preset station
Press repeatedly the “MEMORY RADIO” button to select the desired preset station number.

ALARM

1. In off mode, press the “ALARM SET” button to enter the alarm 1 setting. The hour of alarm 1 flashes in the display.
2. Press the button to adjust the hour setting and press the “ALARM SET” button to confirm. The minute flash.
3. Press the button to adjust the minute setting and press the “ALARM SET” button to confirm. The display change to the hour of alarm 2 settings.
4. Press the button to adjust the hour of alarm 2 and press the “ALARM SET” button to confirm.
5. Press the button to adjust the minute of alarm 2 and press the “ALARM SET” button to confirm.
6. Now the alarm is set.

Note: If no button will be pressed for 10 seconds, the display shows the clock display again.
Activate or deactivate the alarm
Press repeatedly the “AL1” or “AL2” button to select one of the following wake-up functions:

ALARM
RADIO

No indicator| Wake up with a signal tone.
Wake up with the radio.
Wake up with a vibration pad
Alarm off.
---|---

Snooze function
Press the “SNOOZE” button to interrupt the wake-up tone or the vibration pad function. The alarm starts again after 6 minutes. If snooze is activated, the AL1 or AL2 indicator flashes.
Deactivating the sounding alarm
Press a button during the alarm (except the “SNOOZE” button) to switch off the alarm sound.

SLEEP

To set the sleep timer, press during on mode the “SLEEP/TIMER” button repeatedly to adjust the minutes 5, 10, 15, 30, 45, 60, 75, 90, and OFF. The sleep indicator lights up on the display

USB CHARGING

You can charge a device on the USB socket (5V 1A) on the front side of the unit.

FACTORY DEFAULT

If an error occurs on the clock, it may result from electrostatic interferences of other devices. To resolve this, you can remove the power supply and the backup battery, then the unit can be restored to the factory default.

Technical changes and misprints reserved.
Copyright by Woerlein GmbH, 90556 Cadolzburg,www.soundmaster.de
Duplication only with the permission of Woerlein GmbH

Hersteller
Wörlein GmbH
Gewerbestrasse 12
D 90556 Cadolzburg
GERMANY| Tel.: +49 9103/71670
Fax.: +49 9103/716712
Email. [email protected]
Web: www.soundmaster.de
---|---

References

• soundmaster®

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>