PROMAC JD-3285-M Drill Press Instruction Manual

PROMAC JD-3285-M Drill Press

Product Information

This is a drill press manufactured by TOOL FRANCE SARL. It is designed for drilling wood and machinable metal and plastic materials. The drill press comes with various features such as a chuck and arbor, depth stop, spindle speeds, table tilt adjustment,  cross laser adjustment, and LED work light adjustment. The productis covered by a warranty against material defects and manufacturing faults. Additional details about the warranty can be found in the General Terms and Conditions (GTC).

Product Usage Instructions

1. Transport and Start-Up:
   • Transport and install the drill press according to the instructions provided.
   • Assemble the machine properly.
   • Connect the drill press to the mains power supply.
   • Start the operation of the machine.
2. Machine Operation:
   • Follow the setup and adjustment instructions provided in the manual.
   • To remove the chuck and arbor, refer to the instructions.
   • Adjust the depth stop according to your requirements.
   • Change spindle speeds as needed for your drilling tasks.
   • Adjust the table tilt for angled drilling.
   • Perform cross laser adjustment for accurate drilling.
   • Adjust the LED work light for better visibility.
3. Maintenance and Inspection:
   • Regularly perform maintenance tasks as specified in the manual.
   • Inspect the machine for any issues or damage.
4. Troubleshooting:
   • Refer to the troubleshooting section of the manual for common issues and their solutions.
5. Environmental Protection:
   • Follow the guidelines provided in the manual for proper disposal and recycling of the product.
6. Available Accessories:
   • Refer to the list of available accessories for this drill press.

For more detailed information and safety instructions, please refer to the complete user manual.

Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new PROMAC-machine. This manual has been prepared for the owner and operators of a JD-3285-M or JD-3285-T drill press to promote safety during installation, operation and maintenance procedures. Please read and understand the information contained in these operating instructions and the accompanying documents. To obtain maximum life and efficiency from your machine, and to use the machine safely, read this manual thoroughly and follow instructions carefully.

Declaration of conformity

On our own responsibility we hereby declare that this product complies with the regulations* listed on page 2. Designed in consideration with the standards**.

Warranty

• TOOL FRANCE SARL guarantees that the supplied product(s) is/are free from material defects and manufacturing faults.
• This warranty does not cover any defects which are caused, either directly or indirectly, by incorrect use,  carelessness, damage due toaccidents, repairs or inadequate maintenance or cleaning as well as normal wear and tear.
• Further details on warranty (e.g. warranty period) can be found in the
• General Terms and Conditions (GTC) that are an integral part of the contract.
• These GTC may be viewed on the website of your dealer or sent to you upon request.
• TOOL FRANCE SARL reserves the right to make changes to the product and accessories at any time.

Safety

Authorized use

• This drill press is designed for drilling wood and machinable metal and plastic materials only. Machining of other materials is not permitted and may be carried out in specific cases only after consulting with the manufacturer.
• Never cut magnesiumhigh danger of fire!
• The workpiece must allow to safely be loaded and clamped for machining. The proper use also includes compliance with the operating and maintenance instructions given in this manual.
• The machine must be operated only by persons familiar with its operation and maintenance and who are familiar with its hazards.
• The required minimum age must be observed.
• The machine must only be used in a technically perfect condition.
• When working on the machine, all safety mechanisms and covers must be mounted.
• In addition to the safety requirements contained in these operating instructions and your country’s applicable regulations, you should observe the generally recognized technical rules concerning the operation of wood- and metal-working machines.
• Any other use exceeds authorization.
• In the event of unauthorized use of the machine, the manufacturer renounces all liability and the responsibility is transferred exclusively to the operator.

General safety notes
Drill press can be dangerous if not used properly. Therefore the appropriate general technical rules as well as the following notes must be observed.

Read and understand the entire instruction manual before attempting assembly or operation.

Keep this operating instruction close by the machine, protected from dirt and humidity, and pass it over to the new owner if you part with the tool. No changes to the machine may be made.  Daily inspect the function andexistence of the safety appliances before you start the machine. Do not attempt operation in this case, protect the machine by unplugging the power cord. Before operating the machine, remove tie, rings, watches, other jewellery, and roll up sleeves above the elbows. Remove all loose clothing and confine long hair.

Wear safety shoes; never wear leisure shoes or sandals. Always wear the approved working outfit:

• safety goggles
• ear protection
• dust protection

Do not wear gloves while operating this machine.

• Install the machine so that there is sufficient space for safe operation and workpiece handling.
• Keep work area well lighted.
• The machine is designed to operate in  closed rooms and must be boltedstable on firm and levelled table surface or on the supplied cabinet stand.
• Make sure that the power cord does not impede work and cause people to trip.
• Keep the floor around the machine clean and free of scrap material, oil and grease. Stay alert!
• Give your work undivided attention.
• Use common sense. Do not operate the machine when you are tired.
• Keep an ergonomic body position. Maintain a balanced stance at all times.

Do not operate the machine under the influence of drugs, alcohol or any medication. Be aware that medication can change your behaviour.

Never reach into the machine while it is operating or running down.

• Keep children and visitors a safe distance from the work area.
• Never leave a running machine unattended. Before you leave the workplace switch off the machine.
• Do not operate the electric tool near inflammable liquids or gases.  Observe the fire fighting and fire alertoptions, for example the fire extinguisher operation and place.
• Do not use the machine in a dump environment and do not expose it to rain.
• Before machining, remove any nails and other foreign bodies from the workpiece.
• Work only with well sharpened tools.
• Machine only stock which rests securely on the table.
• Always close the chuck cover before you start the machine.
• Specifications regarding the maximum or minimum size of the workpiece must be observed.
• Do not remove chips and workpiece parts until the machine is at a standstill.
• Do not stand on the machine.
• Connection and repair work on the electrical installation may be carried out by a qualified electrician only.

Make all machine adjustments or maintenance with the machine unplugged from the power source.

• Never place your fingers in a position where they could contact the drill or other cutting tool if the work piece should unexpectedly shift or your hand should slip.
• Secure workpiece against rotation.
• Use fixtures, clamps or a vice to hold the workpiece.
• Never hold the workpiece with your hands alone.
• Whenever possible, position the work piece to contact the left side of the column. If it is too short or the table is tilted, clamp solidly to the table. Use the table slots or clamping ledge around the outside of the table.
• When using a drill press vice, always fasten it to the table.
• Never do any works “freehand” (handholding the work piece rather than supporting it on the table), except when polishing.
• Securely lock the head to the column and the table bracket to the column before operating the press.
• Never move the head or the table while the machine is running.
• If a work piece overhangs the table such that it will fall or tip if not held, clamp it to the table or provide auxiliary support.
• Do not use wire wheels, router bits, shaper cutters, circle cutters, or rotary planers on this drill press.
• To avoid injury from parts thrown by the spring, follow instructions exactly as given when adjusting the spring tension of the quill.
• To avoid injury from parts thrown by the spring, follow instructions exactly as given in chapter 7.5.

Remaining hazards
When using the machine according to regulations some remaining hazards may still exist. The rotating drill bit can cause injury. Thrown workpieces and workpiece parts can lead to injury. Dust, chips and noise can be health hazards. Be sure to wear personal protection gear such as safety goggles and dust mask. Use a suitable dust collection system. The use of incorrect mains supply or a damaged power cord can lead to injuries caused by electricity.

Machine specifications

Technical data

• Drilling capacity(Iron/Steel) 32/32mm
• Spindle to column 215mm
• Spindle travel 85mm
• Spindle taper MT-3/B16
• Chuck size 16mm
• Column diameter 80mm
• Table size 290 x 290 mm
• Overall height 1050 mm
• Number of speeds 16
• Range of speeds 180 – 3000 rpm
• Net weight 61 kg

JD-3285-M:

• Mains 230V ~1/N/PE 50Hz
• Output power 0.75 kW (1 HP) S1
• Reference current 4.6 A
• Extension cord (H07RN-F): 3×1.5mm²
• Installation fuse protection 10A

JD-3285-T:

• Mains 400V ~3L/N/PE 50Hz
• Output power 0.75 kW (1 HP) S1
• Reference current 2.4 A
• Extension cord (H07RN-F): 5×1.5mm²
• Installation fuse protection 10A

Noise emission
Acoustic pressure level (according to EN ISO 11202): Idling LpA 71,8 dB(A) In operation LpA 84,0 dB(A) The specified values are emission levels and are not necessarily to be seen as safe operating levels. As workplace conditions vary, this information is intended to allow the user to make a better estimation of the hazards and risks involved only.

Content of delivery

• Head assembly Table
• Column and bracket assembly Machine base
• 16mm keyless chuck MT-3 arbor 3 downfeed handles
• Table bracket lock handle
• Table bracket rising handle
• Drill chuck guard Drift key
• Operating tools Assembly kit
• Operating manual Spare parts list.

Transport and start up

Transport and installation
The machine is designed to operate in closed rooms and must be placed stable on firm and levelled ground. The machine can be bolted down if required. For packing reasons the machine is not completely assembled.

Assembly
If you notice transport damage while unpacking, notify your supplier immediately. Do not operate the machine! Dispose of the packing in an environmentally friendly manner. Clean all rust protected surfaces with a mild solvent. Attach the column assembly (A, Fig. 1) to the base (B, Fig. 1) with four M10 hex cap bolts (C, Fig 1). Tighten firmly.

Thread the table bracket lock handle(A, Fig 2) into the table bracket (B, Fig 2).

Slide the table bracket rising handle (B, Fig 3) onto the table bracket shaft

Turn the handle until the set screw is opposite the flat section on the shaft and tighten the set screw (A, Fig 3).Insert the table into the table bracket. Tighten the table lock handle. With the aid of a second person, carefully lift the head onto the column top. Caution: The head assembly is heavy! Use care when lifting onto the column! Rotate the head assembly until the sides of the belt cover are parallel with the sides of the base. Tighten two set screws (A, Fig. 4).

Install three down feed handles (A, Fig. 5) into the down feed hub (B).

The Drill Chuck Guard Adjustment (Fig. 6.1).

This clear plastic shield should be used whenever conducting a drilling or tapping operation. Clean the safety shield periodically to provide a clear view of the work piece. Adjustments can be done as follows.

1. Adjust the internal cover shield to have better range protection.
2. If both internal and external shields cannot provide enough protection, loosen locking bolt (M) to shift setting ring (N) in proper position.
   • Note: Make sure the bolt (M) aligning to the groove (aimed by the arrow), otherwise the interlock switch would not be triggered when the shields being opened (Fig. 6.2).

Raise the table to approximately 200mm below the spindle assembly. Lock the table. Place a piece of scrap wood on the table. Thoroughly clean the spindle opening, the arbor, and the chuck.
Important:
These three pieces must be free of any rust protection or lubricant. If they are not clean, the arbor and chuck will fail to seat in the spindle and will fall out. Place the arbor into the chuck. Twist the chuck to retract the chuck jaws if they are exposed. Place the arbor and chuck assembly into the spindle. Turn the arbor and chuck assembly until the tang on the arbor engages the slot at the end of the spindle. Lower the down feed handle so that the chuck meets the scrap wood. Pressure on the down feed handle once the chuck meets the scrap wood seats the arbor and chuck into the spindle ( see Fig 7).

Mains connection
Mains connection and any extension cords used must comply with applicable regulations. The mains voltage must comply with the information on the machine licence plate. The mains connection must have a 10 A surge-proof fuse. Only use power cords marked H07RNF Connections and repairs to the  electrical equipment may only becarried out by qualified electricians.

Starting operation
You can start the machine with the green on button. The red button on the main switch stops the machine (Fig. 8).

Machine operation

Always adjust the table and the depth stop to prevent drilling into the table. Use a back-up piece of scrap wood to cover the table. This protects both the table and the drill bit. Secure workpiece to the table with clamps or a vice to prevent rotating with the drill bit. Feed the bit into the material with only enough force to allow the drill bit to work. Feeding too slowly may cause burning of the workpiece. Feeding tooquickly may cause the motor to stop and/or the drill bit to break.

Recommended speeds for a 10mm HSS drill:

• Wood: 2000 RPM
• Plastic: 1500 RPM
• Aluminum: 1500 RPM
• Brass: 1500 RPM
• Cast iron: 1000 RPM
• Mild steel: 800 RPM
• High carbon steel: 600 RPM
• Stainless steel: 300 RPM

Generally speaking, the smaller in relation the drill bit, the greater the RPM required. Wood requires higher speeds than metal. Metal is usually drilled at slower speeds; cutting oil is applied if necessary.

Warning:

• Always keep your hands well clear of the rotating bit.
• Do not remove chips and workpiece parts until the machine is at a standstill.
• Always close the chuck guard and pulley cover before you start the machine.
• When using a drill press vice, always fasten it to the table.
• Never do any works “freehand” (handholding the work piece rather than supporting it on the table), except when polishing.
• Support long workpieces with helping roller stands.
• Do not use wire wheels, router bits, shaper cutters, circle cutters, or rotary planers on this drill press.
• Never cut magnesiumhigh danger of fire!

Setup and adjustments

General note:
Setup and adjustment work may only be carried out after the machine is protected against accidental starting by pulling the mains plug.

Removing the Chuck and Arbor

• Unplug the machine from the power source.
• Lower the quill using the down feed handle.
• Rotate the spindle to align the key in the spindle with the key hole in the quill.
• Insert the drift key (A, Fig 9) into the aligned slots and tap lightly. Have another person (or a protected table) catch the chuck and arbor assembly as it falls away from the spindle.

Adjusting the Depth Stop
To drill multiple holes at the same preset depth, use the depth stop: With the drill bit in the chuck, lower the down feed handle to advance the chuck to the desired point. Turn the depth scale collar (C, Fig. 10) counter-clockwise until it stops moving. Tighten the depth scale lock (D).

The drill bit will now advance only to this point.
Changing Spindle Speeds
Loosen the locking screw on the pulley cover, then open the cover. A spindle speed and belt arrangement chart is found on the inside of the belt cover (Fig 11). Refer to this chart whenever changing speeds.

To change spindle speeds: Unplug the machine from the power source. Loosen two side bar bolts found on each side of the head assembly. (A, Fig 12).

Rotate the tension adjuster (B) to bring the motor base as close to the head as possible. Change the belts location according the speed chart and the speed you desire. Rotate the tension adjuster (B) to tension the belts. Tighten two slide bar bolts (A, Fig. 12). Belts are properly tensioned when finger and thumb pressure midway between the two pulleys causes approximately 10 mm deflection. Close and lock the pulley cover.

Table Tilt Adjustment
Disconnect the machine from the power source (unplug).

Loosen the hex cap bolt (C) to tilt the table.
Caution: Only loosen the hex cap bolt slightly, otherwise the table assembly will separate from the column and fall. Tighten the hex cap bolt.

Return Spring Adjustment

• Disconnect the machine from the power source (unplug).
• The return spring is adjusted at the factory and should not need further adjustment. If adjustment is necessary:
• Unplug the machine from the power source.
• Loosen two lock nuts (A, Fig 14) approximately 6mm.

Firmly hold the coil spring cover (B). Pull out the cover and rotate until the pin (C) on the return spring plate engages the next notch in the coil spring cover. Turn the cover clockwise to decrease tension and counterclockwise to increase tension. Tighten two lock nuts (A). Do not overtighten. Nuts should not contact the housing when tight.

Cross Laser Adjustment
The lasers are designed for use with twist drill bits. There will be shadowing with wider tools, such as Forstner bits, therefore use will be limited. The two laser beams need to meet at the drill centre (Fig 15).

The Laser Assembly has been installed and pre-set at the factory. To adjust, install a small drill bit and rotate lasers (A, Fig 16) gently with a set of pliers. Loosen Screw (C) for adjustment.
ATTENTION: Class 2 Laser

• Do not stare into beam of laser
• Do not view directly with optical instruments
• Do not point the laser beam at people or animals.
• Do not use the laser beam on highly reflective materials. Reflected laser light is dangerous.
• A defective laser beamer may be replaced only, not repaired.

LED Work Light Adjustment
The integrated LED work light is adjustable. Push on the rim of the light to adjust (B, Fig 16).

Maintenance and inspection

General notes:

• Maintenance, cleaning and repair work may only be carried out after the machine is protected against accidental starting by pulling the mains plug.

Lubrication:

• Periodically lubricate the gear and the rack, the table elevation mechanism, the drive splines (grooves) in the spindle, and the teeth of the quill gently with grease.

Clean the machine regularly.

• Defective safety devices must be replaced immediately.
• Repair and maintenance work on the electrical system may only be carried out by a qualified electrician.

Trouble shooting

Motor doesn’t start

• No electricitycheck mains and fuse.
• Defective switch, motor or cordconsult an electrician.

Chuck will not stay on spindle

• Oil or grease on contact surfacesclean the tapered surfaces of chuck and spindle.

Machine vibration

• Incorrect belt tension- Adjust belt tension.
• Dry spindle quilllubricate spindle quill.
• Spindle pulley loosetighten retaining nut.
• Motor pulley loose- Tighten set screw.
• dull drill bitresharpen drill bit.

Drill bit burns

• incorrect speedreduce speed.
• Chips cloggedretract drill bit frequently
• dull drill bitresharpen drill bit.
• feeding too slowfeed faster.

Drill leads off

• cutting lips or angle not equalresharpen drill bit correctly.
• drilled hole off centerdrill a pilot hole first.
• bent drill bituse a proper drill bit.
• drill bit not properly installedinstall drill bit correctly.

Environmental protection

Protect the environment
 Your appliance contains valuable materials which can be recovered or recycled. Please leave it at a specialized institution. This symbol indicates separate collection for electrical and electronic equipment required under the WEEE Directive (Directive 2012/19/EC) and is effective only within the European Union.

Available accessories
Refer to the PROMAC-Pricelist.

CE-Conformity Declaration

Manufacturer

We hereby declare that this product complies with the regulations

2006/42/EC

• Machinery Directive

2014/30/EU

• electromagnetic compatibility
• designed in consideration of the standards

Responsible for the Documentation

2021-01-06 Christophe SAINT SULPICE, General Manager TOOL France SARL

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>