LAMAX PartyBoomBox500 Bluetooth Speaker User Guide
- June 7, 2024
- LAMAX
Table of Contents
PartyBoomBox500
Rear Panel and Controls
| 1. Volume level control | 7. AUX iNpUt |
|---|---|
| 2. Bass level control | 8. Microphone input |
| 3. treble level control | 9. Charging adapter input |
| 4. Microphone volume level control | 10. LED On/Off switch |
| 5. Microphone echo effect level control | 11. power switch |
| 6. 12V battery input |
Charging and LED Indicators
Fully charge the speaker battery before first use, using the adapter included.
Indicators:
– LED glows red – the speaker battery is charging
– LED glows green – the speaker battery is fully charged
Note: Low battery status results in a gradual reduction in performance
and possible audio outages. in this case, immediately connect the power to the
speaker or turn it off.
Powering On / Off
to turn the speaker on/off, press the pOWER button. the display lights up and
a beep sounds.
Pairing via Bluetooth
- turn on the speaker and make sure Bluetooth mode is selected on the display. if it is not selected, press the MODE button below the rear panel display to select it. the speaker is now ready for pairing.
- Activate the Bluetooth connection on your smartphone or another device. Select “LAMAX partyBoomBox500” from the list of available devices. When pairing is successful, the speaker beeps.
- playback can be controlled either by a paired device, directly on the speaker or via remote control.
Note: the Bluetooth connection works best within 10 meters in an open area.
TWS
to pair two speakers, turn on both speakers, and make sure they are not paired
with the multimedia device. Set both devices to the Bluetooth mode by pressing
the MODE button, the LCD display shows “no B”. Hold down the pLAY/pAUSE button
for 5s on one of them, which will be the main one. A beep sounds and the main
speaker acts as the right channel. The other speaker also beeps and acts as
the left channel. to unpair, the speakers, hold the same MODE button on the
main speaker or turn one-off.
Player Controls
| 1. SD carD | input for an SD card. Select this source using the MODE button. |
|---|---|
| 2. Play/PauSe | press to pause or play music. |
| 3. PreviouS | Press to skip to the previous track. |
| 4. Next | Press to skip to the next track. |
| 5. rePeat | press to choose between “loop current track” and “loop all |
tracks”.
6. MoDe| press to select the music source: Bluetooth, SD card, USB, AUX, FM
radio.
the icon on the left of the display will show you which source is currently
selected.
7. USB| input for a USB device (e.g. flash drive). this input is for music
playback
only. You cannot charge other devices using this USB input. We do not
recommend using USB extension cables. Do not disconnect the USB
drive from the device while the USB drive is playing or reading data.
Using an External AUX Source
- Select “AUX” using the MODE button on the rear panel of the unit.
- Connect your audio device to the external AUX iN input on the rear panel. You can then control playback on the external audio device or on the speaker itself.
Using the Microphone
- Connect the microphone that comes included to the MiC iN input on the rear panel of the unit and turn the microphone switch to the ON position.
- turn the MiC VOL control on the rear panel to increase or decrease the microphone volume.
- turn the ECHO control on the rear panel of the device to increase the echo effect on the microphone.
Note: if you are placing the microphone next to the speaker, turn off the
microphone.
Otherwise, the speaker may feedback, causing a loud uncomfortable sound.
Placement
The speaker was designed to be placed on the floor, on any solid and stable
surface, or on a tripod stand (tripod not included).
Note: if you will not be using the speaker for a long time, make sure it is
turned off and unplugged.
Remote control
| 1. Standby mode ON/OFF
---|---
2. Select input
3. Sound modes
4. Volume up
5. play/pause
6. Music playback: Next track, FM: + 0.1 MHz (press)/Next FM channel (hold)
7. Repeat mode
8. Select track from USB and SD/
Select FM channel
9. Scan FM channels
10. Volume down
11. Music playback: previous track, FM: – 0.1 MHz (press)/previous FM channel
(hold)
12. Mute
Parameters
| total peak power | 500 W |
|---|---|
| RMS | 80 W |
| Subwoofer Diameter | 30,5 cm |
| tweeter Diameter | 25 mm |
| Frequency Range | 40 – 20000 Hz |
| Sensitivity | 90 dB |
| Number of Bands | 2 |
| Battery | 12 V / 3 Ah |
| input (DC jack) | 15 V / 2 A |
A full and up-to-date version of the user manual is available here:
https://www.lamax-electronics.com/downloads/lamax-partyboombox/manual
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>