PROMAC 212VLL Drill Press User Manual

**PROMAC 212VLL Drill Press User Manual

**

CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Keep this manual with tools.

SAFETY SYMBOLS

Some of the following symbols may be used on your tool. Please study them and learn their meaning. proper interpretation of these symbols will allow you to operate the tool better and safer.

understand operator’s manual
| Wear safety glasses| Operation of power tool can result in foreign objects being thrown into eyes
| Wear respiratory Protection| Use of this tool can generate dust which may cause respiratory injury
| Wear hearing Protection| Noise from this productcan contribute to hearing loss
| Wear gloves| Wear gloves to reduce risk of injury
| Warning symbol| Alerts user to warning messages

SAFETY INSTRUCTIONS

The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger. The instructions and warnings they give are no substitutes for propper accident prevention measures.

WARNING: Be sure to read and understand all safety insructions in this manual, including all safety alert symbols such as “DANGER”, “WARNING” and “CAUTION”, before using this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

SYMBOL MEANING

SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, OR CAUTION. May be used in conjuntion with other symbols or pictographs.

DANGER: Failure to obey this warning WILL result in death or serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

WARNING: Failure to obey this safety warning CAN result in death or serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury

CAUTION:   Failure to obey this safety warning MAY result in personal injury to yourself or othersor property damage. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

SAFETY INSTRUCTIONS

GENERAL SAFTY RULES

Safety is a combination of common sense, staying alert, and knowing how your bench drill press works.

WARNING: TO AVOID MISTAKES THAT COULD CAUSE SERIOUS INJURY, DO NOT PLUG IN THE BENCH DRILL PRESS UNTIL THE FOLLOWING STEPS HAVE BEEN READ AND UNDERSTOOD.

1. READ and become familiar with this entire instruction manual. LEARN the tool’s applications, limitations, and possible hazards.
2. AVOID DANGEROUS CONDITIONS. DO NOT use power tools in wet or damp areas or expose them to rain. Keep work area well-lit.
3. DO NOT use power tools in the presence of flammable liquids or gases.
4. ALWAYS keep your work area clean, uncluttered, and well-lit. DO NOT work on floor surfaces that are slippery with sawdust or wax.
5. KEEP BYSTANDERS AT A SAFE DISTANCE FROM the work area, especially when the tool is in operation. NEVER allow children near the tool.
6. DO NOT FORCE THE TOOL to do a job for which it was not designed.
7. DRESS FOR SAFETY. DO NOT wear loose clothing, gloves, neckties, or jewellery (rings, watches, etc.) when operating the tool. Inappropriate items can get caught and draw you into moving parts. ALWAYS wear non-slip footwear, and tie back long hair.
8. WEAR A FACE MASK OR DUST MASK. Drilling into materials produces dust.
9. ALWAYS remove the power cord plug from the power supply outlet when making adjustments, changing parts, cleaning, or working on the tool.
10. AVOID ACCIDENTAL START-UPS. Make sure that the power switch is in the OFF position before plugging in the power cord.
11. REMOVE ADJUSTING TOOLS. ALWAYS MAKE SURE all tools are removed from the bench drill press before turning it ON.
12. NEVER LEAVE A RUNNING TOOL UNATTENDED. Turn the power switch to OFF. DO NOT leave the tool unattended until it has come to a complete stop.
13. NEVER STAND ON A TOOL. Serious injury could result if the tool tips or is accidentally hit. DO NOT store anything above or near the tool.
14. DO NOT OVERREACH. Keep proper footing and balance at all times. Wear oil-resistant rubber-soled footwear. Keep the floor clear of oil, scrap, and other debris.
15. MAINTAIN TOOLS PROPERLY. ALWAYS keep tools clean and in good working order. Follow instructions for lubricating and changing accessories. See Maintenance section.
16. DO NOT operate the tool if you are under the influence of drugs, alcohol or medication that could affect your ability to use the tool properly.
17. CHECK FOR DAMAGED PARTS. Check for alignment of moving parts, jamming, breakage, improper mounting, or any other conditions that may affect the tool’s operation. Any part that is damaged should be properly repaired or replaced before use.
18. MAKE THE WORKSHOP CHILDPROOF. Use padlocks, master switches, and ALWAYS remove starter keys.

DUST GENERATED FROM CERTAIN MATERIALS CAN BE HAZARDOUS TO

YOUR HEALTH. ALWAYS OPERATE THE DRILL PRESS IN A WELL-VENTILATED AREA. USE DUST COLLECTION SYSTEMS WHENEVER POSSIBLE.

ALWAYS WEAR EYE PROTECTION

A bench drill press can throw foreign objects into the eyes which could cause permanent eye damage.
ALWAYS wear safety goggles (not glasses). Ordinary eyeglasses have only impact-resistant lenses…they are NOT safety glasses.

LASER SAFETY

The laser light beam used in this system is Class III. These lasers do not normally present an optical hazard, although staring at the beam may cause flash blindness.

WARNING: DO NOT STARE DIRECTLY AT cTHE LASER BEAM! A HAZARD MAY EXIST IF YOU DELIBERATELY STARE INTO THE BEAM, PLEASE OBSERVE ALL SAFETY RULES AS FOLLOWS:

• THE LASER SHALL BE USED AND MAINTAINED IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS.
• NEVER AIM THE BEAM AT ANY PERSON OR AN OBJECT OTHER THAN THE WORKPIECE.
• DO NOT PROJECT THE LASER BEAM INTO THE EYES OF OTHERS.
• ALWAYS ENSURE THE LASER BEAM IS AIMED AT A WORKPIECE THAT DOES NOT POSSESS REFLECTIVE SURFACES, AS THE LASER BEAM COULD BE PROJECTED INTO YOUR EYES OR THE EYES OF OTHERS.

SPECIFIC SAFETY RULES FOR BENCH cDRILL PRESSES

WARNING: DO NOT OPERATE YOUR BENCH DRILL PRESS UNTIL IT IS COMPLETELY ASSEMBLED AND INSTALLED ACCORDING TO THE

INSTRUCTIONS

1. NEVER TURN THE BENCH DRILL PRESS ON until the table is clear of all foreign objects (tools, scraps, etc.).
2. ALWAYS KEEP hands and fingers away from the drill bit.
3. DO NOT drill materials that do not have a flat surface—unless a suitable support is used (clamp or vise).
4. NEVER start the drill press with the drill bit pressed against the work piece.
5. MAKE SURE the table lock is tightened before starting the bench drill press.
6. NEVER layout, assemble, or set-up any work on the table while the drill is ON.
7. MAKE SURE drill bit is securely locked in the chuck.
8. MAKE SURE chuck key is removed from the chuck before turning power ON.
9. ADJUST the table or depth stop to avoid drilling into the table.
10. ALWAYS stop the drill before removing scrap pieces from the table.
11. USE CLAMPS or a vise to secure a work piece to the table. This will prevent the work piece from rotating with the drill bit.
12. DO NOT wear gloves when operating a drill press.
13. BEFORE LEAVING THE MACHINE, SHUT THE POWER OFF, remove the drill bit and clean the table.
14. SET THE DRILL PRESS to the speed that is appropriate for the material being drilled.
15. SHOULD any part of your bench drill press be missing, damaged, or any electrical component fail to perform properly, shut the power OFF and unplug the drill press. Replace missing, damaged, or failed parts before resuming operation.

ELECTRICAL REQUIREMENTS POWER SUPPLY AND MOTOR SPECIFICATIONS

WARNING: To avoid electrical hazards, fire hazards, or damage to the tool, use proper circuit protection. Use a separate electrical circuit for your tools. To avoid shock or fire, if power cord is worn or cut, or damaged in any way, have it replaced immediately.

GROUNDING INSTRUCTIONS

This tool must be grounded while in use to protect the operator from electrical shock.

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistance for electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment-grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances.
DO NOT MODIFY THE PLUG PROVIDED. If it will not fit the receptacle, have the proper receptacle installed by a qualified electrician.
IMPROPER CONNECTION of the equipment-grounding conductor can result in risk of electric shock. The conductor with green insulation (with or without yellow stripes) is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, DO NOT connects the equipment- grounding conductor to a live terminal.
CHECK with a qualified electrician or service person if you do not completely understand the grounding instructions, or if you are not sure the tool is properly grounded.

Refer to nether picture:

WARNING: Improper connection of equipment grounding conductor can result in the risk of electrical shock. Equipment should be grounded while in use to protect operator from electrical shock.

WARNING: This machine is for indoor use only. Do not expose to rain or use in damp locations.

GUIDELINES FOR EXTENSION CORDS

USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and cause overheating.
Be sure your extension cord is properly wired and in good condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it. Protect your extension cords from sharp objects, excessive heat and damp or wet areas.

Wiring Diagram

Parts list of the electrical system

Index No.| Function| Specifications| Qty.| Manufacturer| Remarks
---|---|---|---|---|---
| Power cord| H05VV-F 3G0.75mm²| 1| |
SB1| Chuck guard Microswitch| 250V/8(6)A| 1| KJD6|
SB2| Belt cover Microswitch| 250V/8(6)A| 1| Hongyi| BC-8
SB3| Main switch| 6(4)A 250V| 1| CK-1|
SB4| Laser Switch| 6A 250V/10A 125V| 1| KCD1|
SB5| Light switch| 6A 250V/10A 125V| 1| KCD1|
VD1| Laser lamp| LDBXQ03B| 1| DKLD|
VD2| Laser lamp| LDBXQ03B| 1| DKLD|
VD3| Working light| 220V 5W| 1| E26|
M| Motor| 550W 230V 50Hz| 1| |

OVERVIEW

c

A power ON switch
B power OFF switch
C Digital speed readout
D Chuck
E Safety goggles
F Table
G Large, heavy-duty feed handles
H Housing cover screw
I Housing cover
J Column
K Rack
L Crank handle
M Column support
N Base
O Table lock bolt
P Bevel scale
Q Laser line ON/OFF switch
R LED work light switch
S Support lock handle
T Speed control handle
U Power cord

SPECIFICATIONS

BENCH DRILL PRESS WITH LASER LINE

MODEL NO.: 212VLL
MOTOR: 230V 50Hz
POWER: 550W
SPEED: 450-2500RPM
SWING: 12” (155 mm)
SPINDLE TAPER: MT2
CHUCK CAPACITY: 1/8-5/8” (3-16 mm)
QUILL DIAMETER: 2 3/5” (65 mm)
STROKE: 3 1/8” (80 mm)
CAPACITY: 6” (152 mm) (chuck to column) 19 1/2” (495 mm) (chuck to base)
TABLE TILT: 0 to 45°left and right
LASER: Class III, transformer powered
WEIGHT: 77.8 lb (35 kg)

ASSEMBLY AND ADJUSTMENTS

UNPACKING AND CLEANING

Unpack the bench drill press and all its parts, and compare against the list below. Do not discard the carton or any packaging until the bench drill press is completely assembled.
To protect the bench drill press from moisture, a protective coating has been applied to the machined surfaces. Remove this coating with a soft cloth moistened with kerosene. Do not use acetone, gasoline, or lacquer thinner to clean. Apply a coat of paste wax to the table and column. Wipe all parts with a clean, dry cloth.

A Head/motor assembly
B Column assembly and table bracket
C Table
D Base
E Chuck
F Chuck key
G Table lock handle
H Hex head bolts (4)
I Table crank handle
J Hex keys (2)
K Feed and speed handles (4)
L LED bulb
M Table adjustment wrench
N Wedge
O Goggle rod
P Safety goggle
Q Screw gasket
R Goggle rod shaft screw
S Fixing bolt of goggle rod
T Safety goggle screws (2)

ASSEMBLY

The column assembly (column, column support, rack, rack collar, and table support bracket) must be attached to the base. The table and table support handles must be attached to the table support bracket. The motor housing must be attached to the column.

WARNING: IF ANY PART IS MISSING OR DAMAGED, DO NOT PLUG THE BENCH DRILL PRESS IN UNTIL THE MISSING OR DAMAGED PART IS REPAIRED OR REPLACED, AND ASSEMBLY IS COMPLETE.

Tools needed for assembly

• Adjustable wrench
• Screwdriver
• Hammer and block of wood

Column assembly to base (Fig. 3)

1. Place the column tube (1) on the base (2), aligning the column support holes to the base holes.
2. Install a hex head bolt (3) in each column support hole and tighten bolts using the adjustable wrench.

Table (Fig. 4)

1. Place the crank handle (1) onto the shaft(2) of the table bracket so the flat of the shaft is under the set screw (3). Tighten the set screw

Drill press head to column (Fig. 5)

The drill press head is heavy. To avoid injury, two people should lift it into position.

1. Carefully lift the drill press head assembly (1) and position it over the column (2).

2. Place the mounting opening (3) on the drill presshead over the top of the column.
   Ensure the drill press head is seated properly on the column.

3. Align the direction of the drill press head with the direction of the base and the table.

4. Tighten the set screw (4) using a hex key

Feed handles (Fig. 6)

1. Insert the three feed handles (1) into the threaded openings on the feed hub (2).
2. Manually tighten handles into openings. Note: When using the bench drill press, one or two of the feed handles may be removed if an unusually-shaped workpiece interferes with handle rotation.

Speed handle (Fig. 7)

1. Insert the feed handle (1) into the threaded opening on the speed hub (2).
2. Manually tighten handle into opening.

Mount the bench drill press (Fig. 8)

The bench drill press must be securely fastened through the mounting holes (1) to a stand or workbench with heavy-duty fasteners. This will prevent the bench drill press from tipping over, sliding, or walking during operation.

IMPORTANT: If the stand or workbench has a tendency to move during operation, fasten the workbench securely to the floor.

LED bulb (Fig. 9)

Insert the LED bulb (1) into the socket (2) in the motor head assembly.
Note: LED bulb can be replaced by any 230V 8L LED bulb if the original one runs out of its lifetime. Install the replacement LED bulb the same way you install the original one.

WARNING: DISCONNECT THE BENCH DRILL PRESS FROM THE POWER SOURCE BEFORE INSTALLING, ADJUSTING, OR REMOVING THE CHUCK.

To install the chuck (Fig. 10)

1. Inspect and clean the taper hole in the chuck (1) and the spindle (2). Remove all grease, coatings, and particles from the chuck and spindle surfaces with a clean cloth.
2. Open the chuck jaws (3) by manually turning the chuck barrel clockwise. Make sure the jaws are completely recessed inside the chuck.
3. Insert the chuck arbor (4) into the opening at the top of the chuck (1).
4. Seat the chuck and chuck arbor on the spindle by placing a block of wood (5; not included) under the chuck (1) and tapping the wood with a hammer (6; not included) or tap the chuck with a rubber mallet (not included).

CAUTION: To avoid damaging the chuck, make sure the jaws are completely recessed into the chuck. Do not use a metal hammer to drive the chuck into the spindle.

To remove the chuck (Fig. 11)

1. Turn the feed handles (1) to lower the chuck (2) to the lowest position.
2. Place a ball joint separator (3; not included) above the chuck and tap the separator lightly with a hammer (4; not included) to cause the chuck to drop from the spindle.

Note: To avoid possible damage to the drill or chuck, be prepared to catch the chuck as it falls.

To install the safety goggles (Fig. 12)

1. Insert the rod (2) into the rod base (1) and fix the screw (3) through the gasket (4).
2. Fix the screw (5) through the rod base.
3. Put the goggle (6) on the rod and fix it with screws (7).

To raise or lower the table (Fig. 13)

1. Loosen the support lock handle (1) and turn the crank handle (2) until the table is at the desired height.
2. Tighten the table lock before drilling

To rotate the table (Fig. 13)

1. Loosen the support lock handle (1) and turn the table around the column to the desired position.
   Note: The rack should rotate around the column with the table support bracket. If the rack binds and will not rotate, slightly loosen the set screw in the rack collar.

2. Tighten the support lock before drilling.

To tilt the table (Fig. 14)

1. Loosen the bevel lock bolt (1) with the table adjustment wrench provided, or with a suitable socket wrench.
2. Tilt the table to the desired angle, using the bevel scale (2) as a basic guide.
3. Re-tighten the bevel lock bolt.
4. To return the table to its original horizontal position, loosen the bevel lock bolt (1).
5. Realign the table to the 0° setting on the bevel scale (2).
6. Tighten the bevel lock bolt with the wrench.

To install drill bits (Fig. 15)

1. Place the chuck key (1) into the side keyhole of the chuck (2), meshing the key with the gear teeth.
2. Turn the chuck key counter-clockwise to open the chuck jaws (3).
3. Insert a drill bit (4) into the chuck far enough to obtain maximum gripping of the chuck jaws.
4. Centre the drill bit in the chuck jaws before final tightening of the chuck.
5. Tighten the chuck jaws using the chuck key to ensure that the drill bit will not slip while drilling.
6. Remove the chuck key

WARNING:   To avoid damaging the chuck, make sure the jaws are completely recessed into the chuck. Do not use a metal hammer to drive the chuck into the spindle.

To square the table to the drill bit (Fig. 16)

1. Insert a 3″ (7.6 cm) long drill bit (1) into the chuck (2) and tighten the jaws with the chuck key.
2. Raise the table with the crank handle (3) approximately 1″ (2.5 cm) below the drill bit.
3. Place a combination square (5) on the table as shown, placing the long straight edge of the combination square against the drill bit. Make sure the drill bit is parallel or aligned exactly to the straight edge of the square.
4. If an adjustment is needed, loosen the bevel lock bolt (6) with a wrench.
5. Tilt the table slightly, until the combination straight edge is aligned perfectly with the drill bit.
6. Tighten the bevel lock when square.

Note: Adjustments for the correct function of your bench drill press return spring have been done at the factory. Please do not modify them. However, prolonged use of the drill press may make some readjustments necessary.

Laser line (Fig. 17 and 18)

WARNING:   DO NOT STARE DIRECTLY AT THE LASER BEAM! A HAZARD MAY EXIST IF YOU DELIBERATELY STARE INTO THE BEAM, PLEASE OBSERVE ALL SAFETY RULES: THE LASER SHALL BE USED AND MAINTAINED IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS:

• NEVER AIM THE BEAM AT ANY PERSON OR AN OBJECT OTHER THAN THE WORK PIECE.
  

• DO NOT PROJECT THE LASER BEAM INTO THE EYES OF OTHERS.
  

• ALWAYS ENSURE THE LASER BEAM IS AIMED AT A WORKPIECE THAT DOES NOT POSSESS REFLECTIVE SURFACES AS THE LASER BEAM COULD BE PROJECTED INTO YOUR EYES OR THE EYES OF OTHERS.

1. Place a workpiece on the table.

2. Turn the laser switch (1) to the ON position.

3. Lower the drill bit to meet the workpiece (2). The two laser lines should cross where the drill meets the workpiece.

4. If the laser needs to be adjusted:
   a. Using a 3 mm hex key, turn the laser adjustment set screws (3) counter-clockwise.
   b. Rotate the laser light housing (4) until the two laser lines intersect where the drill meets the work piece. DO NOT stare directly at the laser lines.

5. Re-tighten the adjustment set screws (3).

Spindle return spring (Fig. 19)

The spindle is equipped with an auto-return mechanism. The main components are a spring and a notched housing. The spring was properly adjusted at the factory and should not be readjusted unless absolutely necessary.

1. Unplug the drill press.
2. Place a screwdriver into the loop (1) to hold the spring in place.
3. Loosen the two housing nuts (2) approximately 1/4″ (6 mm). Do not remove the nuts from the threaded shaft. Do not allow the spring 3 or spring housing to slip out of control.
4. While firmly holding the spring housing (3), carefully pull the spring housing out until it clears the raised notch (4).
5. Turn the housing so that the next notch (5) is engaged with the raised notch (4).
   • To increase the spindle return tension, turn the spring housing counter-clockwise.
   • To decrease the tension, turn the spring housing clockwise.
6. Tighten the two housing nuts. Do not overtighten the two nuts. If the nuts are tightened too much, the movement of the spindle and feed handles will become sluggish.

Angular “play” of the spindle (Fig. 20)

Move the spindle to the lowest downward position and hold in place. Try to make the spindle revolve around its axis while also moving it with a side motion. If there is too much “play”, proceed as follows:

1. Loosen the lock nut (1).

2. Without obstructing the upward and downward motion of the spindle, turn the screw (2) clockwise to eliminate the “play”.
   Note: A little bit of “play” is normal.

3. Tighten the lock nut (1).

To replace the belt (Fig. 21)

WARNING DISCONNECT THE BENCH DRILL PRESS FROM THE POWER SOURCE BEFORE REPLACING THE BELT.

Belt tension and bench drill press speed is controlled by automatic adjustments made to the diameter of the front spindle when the drive handle is moved.
Note: See (Fig. 24) for information on the variable speed function of this bench drill press.

1. Remove the screw that secures the housing cover (1). Open the housing cover.
2. Remove the belt (2) from the housing cover if it is broken. If it is not broken, but is too stretched to operate correctly, work the belt off the drive (motor) spindle (3). Then remove the belt from the front spindle (4).
3. Replace the belt by putting a new belt over the front spindle (4) and carefully sliding the belt over the drive (motor) spindle (3).

WARNING: DO NOT CHANGE THE DRIVE SPEED WHEN THE BENCH DRILL PRESS IS TURNED OFF.

OPERATION

Bench Drill Press ON/OFF switch (Fig. 22)

1. To turn the drill press ON, press the switch (1).
2. To turn the drill press OFF, press the switch (2).

Light and laser Line ON/OFF switches (Fig. 22)

1. The light switch (3) is located below the ON/OFF switch on the left.
2. The laser switch (4) is located below the ON/OFF switch on the right.

Position the table and workpiece (Fig. 23)

1. Always place a piece of backup material (1) (wood, plywood, etc.) on the table underneath the workpiece (2). This will prevent splintering on the underside of the workpiece as the drill bit breaks through.
2. To keep the material from spinning out of control, it must contact the left side (3) of the column as illustrated, or be clamped (4; not included) to the table.

Note: For small workpieces that cannot be clamped to the table, use a drill press vise (not included). The vise must be clamped or bolted to the table to avoid injury.

GENERAL DRILLING GUIDELINES

WARNING:   TO PREVENT THE WORKPIECE AND THE BACKUP MATERIAL FROM SLIPPING FROM YOUR HAND WHILE DRILLING, POSITION WORKPIECE AND BACKUP MATERIAL TO THE LEFT SIDE OF THE COLUMN. IF THE WORKPIECE AND THE BACKUP MATERIAL ARE NOT LONG ENOUGH TO REACH THE COLUMN, CLAMP WORKPIECE AND BACKUP MATERIAL TO THE TABLE. FAILURE TO DO THIS COULD RESULT IN PERSONAL INJURY.

To drill a hole:

1. Mark where you want to drill in workpiece by using a centre punch or a sharp nail or turn ON Laser Line to mark drilling point.
2. Before turning ON the bench drill press, turn the feed handles to bring the drill bit down. Line the drill bit tip up with the mark. Clamp the workpiece in place.
3. Turn ON the bench drill press and pull down on the feed handles with appropriate force needed to allow the drill bit to drill material. Note: FEEDING TOO SLOWLY might cause the drill bit to turn in the chuck. FEEDING TOO RAPIDLY might stop the motor, cause the belt to slip, force the workpiece loose, or break the drill bit. Practice with scrap material to get the feel of the machine before attempting to do any drilling operatio

DRILLING SPEEDS

Important factors when determining the best drilling speed:

• Material type
• Hole size
• Drill bit or cutter type
• Quality desired

Smaller drill bits require greater speed than large drill bits.

Softer materials require greater speed than harder materials. See right speadsheet for recommended speeds for the workpiece material.

Mechanical variable speed (Fig. 24)

This is a variable speed bench drill press. To increase or decrease the speed when operating, raise or lower the speed handle (1).
Use the following table to determine the recommended speed for the drill size you are using and the type of material you are to drill. While drilling, check the speed on the digital speed readout (2) located at the front of the drill press.

Recommended Speed for Dill Size & Material

MAINTENANCE

WARNING:   FOR YOUR OWN SAFETY, TURN THE SWITCH OFF AND REMOVE THE PLUG FROM THE POWER SUPPLY BEFORE MAINTAINING OR LUBRICATING THE BENCH DRILL PRESS.

Vacuum sawdust or metal shavings that accumulates in and on the motor, pulley housing, table, and work surface. Apply a light coat of paste wax to the column and table to help keep these surfaces clean and rust-free.
The ball bearings in the spindle and the V-belt pulley assembly are greased and permanently sealed. Pull the spindle down and oil the spindle sleeve moderately every three months.
Lubricate the table bracket and locking knobs if they become difficult to use.

TROUBLE SHOOTING

1. Incorrect belt tension.
2. Dry spindle.
3. Loose spindle pulley.
4. Loose motor pulley.

| •  Adjust the belt tension. See “To replace the belt” in ADJUSTMENTS.• Lubricate the spindle. See MAINTENANCE section.•  Tighten the retaining nut on the pulley insert.•  Tighten the set screw on the side of themotor pulley.
The drill bit burns or smokes.| ****

1. Drilling at the incorrect speed.
2. The wood chips are not coming out of the hole.
3. Dull drill bit.
4. Feeding the workpiece too slowly.5.   Not lubricated.

| •  Change the speed. See “Variable speed” in OPERATION.•  Retract the drill bit frequently to clear the chips.•  Resharpen or replace the drill bit.• Feed fast enough to cut the workpiece. See “To drill a hole” in OPERATION.• Lubricate the drill bit with cutting oil ormotor oil.
Excessive drill run-outor wobble, drilled hole is not round.|

1. Bent drill bit.
2. Bit improperly installed in the chuck.
3. Worn spindle bearings.
4. Lengths of cutting flutes or angles not appropriate for the hardness of the wood grain.
5. Chuck not properly installed.

| •  Replace the drill bit.•  Reinstall the bit. See “To install drill bits” in ADJUSTMENTS.•  Replace bearings. Take to a qualified service technician.•  Resharpen the drill bit correctly or replace with the appropriate type.•  Reinstall the chuck. See “To install the chuck” in ASSEMBLY.
Drill bit binds in the workpiece.|

1. The workpiece is pinching the bit.
2. Excessive feed pressure.

| •  Support or clamp the workpiece. See “Position the table and workpiece” in OPERATION.•  Feed more slowly. See “Feeding the drillbit” in OPERATION.
Spindle returns too slowly or too quickly.|

1. Spring has improper tension.

| •  Adjust the spring tension. See “Spindle return spring” in ADJUSTMENTS.
Chuck falls off spindle.|

1. Dirt, grease, or oil on the tapered surface on the spindle or in the chuck.

| •  Clean the tapered surface of both the chuck and the spindle with a household detergent. See “To install the chuck” in ASSEMBLY.
The workpiece splinters on the underside.|

1. No backup material under the workpiece.

| •  Always use a backup material. See “Position the table and workpiece” in OPERATION.
The workpiece is slipping from your hand.|

1. 1. Not supported or clamped properly.

| •  Support workpiece using extension wing orclamps. See “Position the table and workpiece” in OPERATION.
Motor will not run.| 1.   Defective or broken switch.2.   Defective or damaged power cord.3.   Open circuit, loose connections, or burned out motor.4.   Blown fuse or circuit breaker.5.   Low voltage.6.   Emergency power off device is not reset after being turned on.| •  Replace the drill bit.• Reinstall the bit. See “To install drill bits” in ADJUSTMENTS.•  Replace bearings. Take to a qualified service technician.•  Resharpen the drill bit correctly or replace with the appropriate type.•  Reinstall the chuck. See “To install the chuck” in ASSEMBLY.•  Reset emergency power off devices:1. keep housing cover be closed completely.See (1) on FIG.24.2.   keep safety goggles be closed completely.SeeFIG.12.
Motor will not start and fuses or circuit breakers blow.| 1.   Short circuit in motor or power cord.2.   Incorrect fuses or circuitbreakers.| • Take to a qualified service technician.•    Replace with correct fuse or circuit breaker for the circuit.
Motor fails to reach full power.| 1.   Overloaded circuit.2.   Improper extension cord.| •  Turn off other machines and retry.•    Replace with proper size extension cord. See ELECTRICAL INFORMATION.
Motor stalls.| 1.   Short circuit in motor.2.   Incorrect fuses or circuit breakers.3.   Overloaded circuit.4.   Low voltage.| •  Take to a qualified service technician.•    Replace with correct fuse or circuit breaker for the circuit.•    Turn off other machines and retry.•    Check the power line for the proper voltage. Use another circuit or have a qualified electricianupgrade the service.

ASSEMBLY DIAGRAM

212VLL PART LIST

Environmental protection

Protect the environment.

Your appliance contains valuable materials which can be recovered or recycled. Please leave it at a specialized institution.

This symbol indicates separate collection for electrical and electronic equipment required under the WEEE Directive (Directive 2012/19/EC) and is effective only within the European Union.

UK Declaration of Conformity

Product:
DRILL PRESS
Model:
212VLL
Brand:
PROMAC

Manufacturer or authorized representative:
TOOL FRANCE S.A.S
Unit 1a Stepnell Park
Off Lawford Road
Rugby
CV21 2UX
United Kingdom

We hereby declare that this product complies with the regulations:
Supply of Machinery (Safety) Regulations 2008
Electromagnetic Compatibility Regulations 2016

designed in consideration of the standards:

BS EN ISO 12100:2010
BS EN 60204-1:2018
BS EN 12717:2001+A1:2009
BS EN IEC 61000-6-2:2019
BS EN IEC 61000-6-4:2019

Responsible for the Documentation:
TOOL FRANCE S.A.S

2021‐12‐17 Christophe SAINT SULPICE, General Manager
TOOL FRANCE S.A.S
9 Rue des Pyrénées, 91090 LISSES, France

References

• Accueil Tool France Promac Tool France

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>