MONOPRICE BT-300ANC Wireless Over Ear Headphones User Manual

**MONOPRICE BT-300ANC Wireless Over Ear Headphones User Manual

**

SAFETY WARNINGS AND GUIDELINES

Please read this entire manual before using this device, paying extra attention to these safety warnings and quidelines. Please keep this manual n safe place for future reference.

• Do not expose this device to water or moisture of any kind.
• Do not use this device while operating a motor vehicle, heavy equipment, walking intraffic, o any other situation in which situational awareness is a key to safety.
• This device contains a Lithium-ion battery. Dispose of this device only in accordance with local, state, or federal requlations for electronic waste.
• Charge the battery before first use and at least once every three months to keep the battery fresh and capable of holding the full charge.
• Do not allow the battery to fully discharge, as doing 50 can damage it and reduce its maximum capacity.
• Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubbor deposits, moisten the cloth with warm water.
• This device has no user serviceable parts. Do not attempt to open, service, or modify this device.

INTRODUCTION

Thank you for purchasing these BT-300ANC Active Noise Cancelling (ANC) Bluetooth® Headphones. These headphones have been designed to provide you with great audio quality, while blocking out ambient noises, such as engines and wind. The BT-300ANC can be used in multiple modes: Bluetooth with ANC active, Bluetooth without ANC, 3 wired ‘connection with ANC active, or a full passive wired connection without ANC to conserve battery life.

FEATURES

• Over-the-ear design with Active Noise Canceling (ANC) circuitry
• Bluetooth radio with support or the A2DP, AVRCP, HF?, and HSP profiles
• Includes the aptX™ audio codec
• Built-in 300mAh Lithium-ion battery
• Up 1019 hours of audio playback with ANC disabled or up to 12 hours with ANC active
• 40mm drivers with neodymium magnets.
• 10508 sensitvity
• Audible low battery indicator

CUSTOMER SERVICE

The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make t right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website wwwmonoprice.com or via email at support@monoprice.com. Check the website for support times and links.

PACKAGE CONTENTS

Please take an inventory of the package contents to ensure you have allthe items listed below. If anything is missing or damaged, please contact Monoprice Customer Service for a replacement.

• 1% BT-300ANC Active Noise Canceling (ANC) Bluetooth® Headphones
• 1% USB-C Charging Cable
• T 35mm Audio Cable
• 1« Carrying Case
• & User’s Manual

PRODUCT OVERVIEW

BATTERY CHARGING

Charge the battery before first use and at least once every three months to keep the. battery fresh and capable of holding a ful cherge. Do not allow the battery to fully discharge, as doing so can damage it and rediuce its maximum capacity.

To charge the battery in the headphones, irst ensure that the headphones are powered off. Next, plug one end of the included USB-C Charging Cable into the Charging Port on the headphones, then plug the other end into a USB power source, such as a computer or USB wall charger. The LED Indicator (Bluetooth) wil iluminate red, indicating that charging s taking place. When charging is complete, the indicator will turn biue.

Note that f the headphones are powered on and the ANC Switch i in the ON position, the LED indlcator (ANG) will luminate green.

When the battery level s low, 2 Battery Low  prompt can be heard n the headphones. The prompt will repeat every 5 minutes.

BLUETOOTH PAIRING

Perform the following steps to pair the headphones with your Bluetooth® device.

1. With the headphones powered off, press and hold the Multi-Function Button (MFE) for 3 seconds to power them on. The LED Indicator (Bluetooth) wil altermately flash red and blue,indicating that the headphones are in Bluetooth pairing mode. Ifinstead of atemately flashing red and blue, the LED Indicator (Bluetooth) fashes blue every 3 seconds, the headphones are already paired with anather device. Tur the headphanes off by pressing and holding the Mult-Function Button (MFE) for 5 seconds.Turn off o disable Bluetooth on the other device, then power the headphones on again.
2. Open the Bluetooth settings on your device and scan for nearby Bluetooth devices.
3. Locate and select the MP33834 entry. If prompted for a passcode, enter 0000 (four zeroes) The LED Indicator (Bluetooth) willstop flashing red and blue and wilinstead flash blue every 3 seconds, indicating itis paired and connected with your device.

OPERATION

Power

• Press and hold the Mult-Function Button (MFE) for 3 seconds to power the headphones ON.
• Press and hold the Mult-Function Button (MFB) for 5 seconds to power the headphones OFF.

Audio Playback

If the headphones are paired with a Bluetooth® enabled device with support for the A2DP and AVRCP profies, you can control the device using the controls on the headphones. Use: the following headphone buttons to perform the indicated functions on your paired device.

• With audio playback stopped or paused, momentarily press the Multi-Function Button (MFB) to start o resume playback.
• While audio is playing, momentarily press the Multi-Function Button (MFE) to pause playback Momentarily press the Volume#/Next Track button to increase the volume level.
• When the maximum volume level i reached, the headphones will emit a beeping sound,
• Momentarily press the Volume-/Prev Track buitton to decrease the volume level When the minimum volume level i reached, the headphones will emit a beeping sound.
• Press and hold the Volume+/Next Track button to skip ahead to the next track.
• Press and hold the Volume-/Prev Track button to skip back to the beginning of the current track. If already at the beginning of the track, it will skip back to the beginning of the previous track.

Phone Calls
If the headphones are paired with a Bluetooth® enabled phone with support for the HFP. and HSP profiles, you can use the headphones to handle calls. Use the following headphone buttons to perform the indicated functions on your paired phone.

• Ifyou receive a call while using the headphones, audio playback willautomatically pause. Momentarily press the Mult-Function Button (MFE) to answer the call
• If you want to reject an incoming cal, press and hold the Multi-Function Button (MFB) button for about 1second, until you hear the audio indication. Audio playback will automatically resume.
• While a callis in progress, momentaril press the Volumet/Next Track button to increase the volume level. When the maximum volume level is reached, the headphones will emit a beeping sound.
• While a callis in progress, momentarily press the Volume-/Prev Track button to decrease the volume level. When the minimurn volume level is reached, the headphones will emit a beeping sound.
• When you are finished with a call, momentarily press the Multi-Function Button (MFB) to terminate the call Audio playback wil automatically resume.
• If you wish to redial the fast number called, double press the Mult-Function Button (o)

Active Noise Cancelling (ANC)

• The headphones must be powered on for the Active Noise Canceling (ANC) feature tofunction.
• The Active Noise Cancelling (ANC) feature can be used with a both Bluetooth® and wired connections.
• To enable the Active Noise Canceling (ANC) feature, side the ANC Switch to the ON position. The LED Indicator (ANG) will iluminate.
• Tt off the Active Noise Cancelling (ANG) feature, side the ANC Switch o the OFF postion. The LED Indicator (ANG) willtur off,

TROUBLESHOOTING

Q. The headphones will not power on.

Al: Charge the batery.

Q2: The battery will not charge.

A2: Confirm that the US power source is active. Check the cable connections. Try replacing the USB-C cable with a known good one.

Q3: The headphones will not pair with the Bluetooth® device.

A3: Ensure that Bluetooth is enabled on your device. Move the device closer to the. headphones during the pairing process. The headphones are already paired with another device.

Qa: The headphones will not maintain a connection with the paired Bluetooth

device.

Ad: Verify that both devices are powered ON. Ensure that Bluetooth s enabled on your device. Move the device closer to the headphones.

Qs: The connection range is very short and/or the sound i distorted or

garbled.

AS: Verify that there are no other devices using the 24GH frequency band. Ensure no obstructions block the signal

Q6: No sound is heard during audio playback.

A6: Confirm that both devices are powered ON, Verify that the audio source device is ‘equipped with the A2DP profile. Ensure that the volume levels on the audio source device and headphones are not set to the minimum. Verify that the audio source is not paused.

SPECIFICATIONS

TECHNICAL SUPPORT

Monoprice s pleased to provide free, live, online technical support to assist you with any. questions you may have about installation, setup, troubleshooting, of product recommendations.If you ever need assistance with your new product, please come online o talk to one of our friendly and knowledgeable Tech Support Associates. Technical support i avalable through the online chat button on our website wwwimonoprice.com or through email by sending a message to tech@monoprice.com. Check the website for support times and links.

REGULATORY COMPLIANCE

Notice for FCC

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Modifying the equipment without Monoprice’s authorization may result i the equipment 10 longer complying with FCC requirements for Class B digital devices. In that event, your fight to use the equipment may be imited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class 8 digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmiul interference in a residential nstallation. This ‘equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmul interference to radio. communications. However, there is no guarantee that interference will not occur ina particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a cicuit different from that to which the receiver is connected,
• Consut the dealer or an experienced radio/TV technician for help.

Radio Notice for FCC

Caution

This FCC Part 15 radio device operates on a non-interference basis with other devices ‘operating at this requency. Any changes or modification to said product not expressly approved by Monoprice, including the use of non-approved antennas, could void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme 5 la norme NMB-003 du Canada.

Radio Notice for Industry Canada

Caution

This IC RSS-210 radio device operates on a non-interference basis with other devices ‘operating at this frequency. Any changes or modification to said product not expressly approved by Monoprice, including the use of non-approved antennas, could void the users authorty to operate tis device.

This device complies with IC RSS-210. Operation i subject to the folowing two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

EU/UK Compliance

Hereby, Monoprice Inc. declares that the radio equipment type Bluetooth Headphones i in ‘compliance

with Directives 2014/53/EU, 2011/65/EU with (EU) 2015/863, Radio Equipment Regulations 2017 and Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The fulltext of the declaration of Conformity is available a the following interet address: httpsy/Awww.monoprice.com/

he information required by EU Radio Equipment Directive/UK Radio Equipment Reguiations related to the frequency band(s) and the maximum radio-frequency power transmitted:

Frequency: 2.402 – 248 GHz; Max Power: 5 dBm

Disposal and Recycling Information

The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electrical and electronics products via designated collection facilties appointed by the govemment o local authorities. Correct disposal and recycling wil help prevent potential negative consequences to the environment and human heaith. For more detailed information about the disposal of your unwanted product, please contacts your local authorities, waste disposal service, or the shop where you purchased the product.

Monoprice and all Monoprice logos are trademarks of Monoprice Inc. The Bluetooth® word mark and logos are registered trademarks of Bluetooth SIG, Inc. Qualcomm® is a trademark of Qualcomm Incorporated, registered in the United States and other countries, aptX™ is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries. Qualcomm® aptX™ is a product of

Monoprice, Inc.
1Painte briv, Suite 400
Brea, CA92621 – USA
www.monoprice.com

Need Help? Wefe here for you!
Contact us: www.monoprice.com/contactus

Specifcations described herein are subject to chang without pror otiication Monoprice™ and all Manoprice ogos ae rademars of Monoprice Inc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>