ATEN CE920L USB DisplayPort HDBaseT 2.0 KVM Extender User Guide

: June 12, 2024
: Aten

Table of Contents

Hardware Overview
Installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ATEN CE920L USB DisplayPort HDBaseT 2.0 KVM Extender User Guide

Hardware Overview

CE920L Front

RS-232 serial port
link LED
power LED

CE920L Rear

power jack
HDBaseT out
DisplayPort in
USB Type-B port
audio out
audio in
long reach mode switch
firmware upgrade switch

CE920R Front

RS-232 serial port
wake up PC pushbutton
video out LED
link LED
power LED
CE920R Rear
power jack
HDBaseT in
DisplayPort out
USB Type-A ports
audio out
audio in
long reach mode switch
firmware upgrade switch

Installation

Connect one end of the supplied microphone cable to the rear of the CE920L, and the other end to a local computer. Do the same using the supplied speaker cable.
Connect the supplied USB cable to the USB Type-B port on the CE920L, and the other end to a USB Type-A port on the local computer.
Connect the supplied DisplayPort cable to the DisplayPort input port on the CE920L, and the other end to the local computer.
Plug one end of an Ethernet cable into the HDBaseT output port on the CE920L, and the other end into the HDBaseT input port on the CE920R.
Plug one of the supplied power adapters into a power source, and then plug the adapter’s power cable into the power jack on the CE920L.
Use a DisplayPort cable to connect the DisplayPort output port on the CE920R to your monitor.
Plug USB devices (mouse, keyboard, etc.) into their respective USB ports on the CE920R.
Plug the microphone and speakers into their respective audio ports on the CE920R.
Plug the second power adapter into a power source, and then plug the adapter’s power cable into the power jack on the CE920R.
To use the wake up PC pushbutton, use an RS-232 serial cable to connect the RS-232 serial port on the CE920L to the local computer.
To control the local computer with a serial device, connect the RS-232 serial port on the CE920L to the local computer as illustrated in step 10, and then connect a hardware / software controller to the RS-232 serial port on the CE920R.
Note : The RS-232 serial port supports bi-directional transmission.
To extend video of 1080p up to 150 m, put either the CE920L or CE920R’s long reach mode switch to ON.

Rack Mount

Using the screws from the supplied mounting kits, secure the mounting bracket to the top or bottom of the CE920.
Using self-prepared screws, secure the mounting bracket to a preferred location on the rack.

Note: Rack screws are not provided. ATEN recommends using M5 Phillips recessed screws

LED Display and System Status

LED	LED Display	System Status
Power	Lights green	The system is receiving power.
******** Link	Lights orange	The connection between the CE920L and CE920R is

stable.
Flashes orange| The HDBaseT transmission is unstable.
Off| The connection between the CE920L and CE920R is off.
**** Video Out| Lights orange| The video display is normal and secured with HDCP.
Flashes orange| The video display is normal but not secured with HDCP.
Off| The video is not displayed.

Note: The Video Out LED is only available on the CE920R.

CE920R Package Contents

1 CE920R USB DisplayPort HDBaseT 2.0 KVM Extender (Remote Unit)
1 mounting kits
4 foot pads
1 power adapter
1 user instructions

CE920L Package Contents

1 CE920L USB DisplayPort HDBaseT 2.0 KVM Extender (Local Unit)
1 microphone cable
1 speaker cable
1 USB Type-A to Type-B cable
1 DisplayPort cable
1 mounting kits
4 foot pads
1 power adapter
1 user instructions

Support and Documentation Notice
All information, documentation, fi rmware, software utilities, and specifi cations contained in this package are subject to change without prior notifi cation by the manufacturer.
To reduce the environmental impact of our products, ATEN documentation and software can be found online at
http://www.aten.com/download/

Technical Support
www.aten.com/support

Scan for more information

ATEN Website