YaberAuto YA50 Car Battery Jump Starter User Manual

June 12, 2024
YaberAuto

YaberAuto YA50 Car Battery Jump Starter

YaberAuto-YA50-Car-Battery-Jump-Starter-PRODUCT

Product Information

Product Name: YaberAuto YA50 Car Battery Jump Starter

Package Contents:

  • Smart Jumper Cables*1
  • Car Jump Starter*1
  • Charging Cable*1
  • User Manual*1
  • Storage Box*1

Key Features:

  • Powerful circuit protection system with Smart Clamps
  • Digital LCD Screen
  • LED Light with three modes (illumination, SOS, and flash)
  • Dual USB Outputs (Output 1: 5V 2.1A, Output 2: 5V 2.4A/9V 2A/12V 1.5A)

Product Usage Instructions

Charging your Jump Starter

  1. Use a 5V 2A / 9V 2A adapter (not included) to charge the product.
  2. It will take approximately 6 hours to fully charge the unit when using a 5V/2A adaptor.
  3. To extend the battery life, charge the unit every 3 months.

Turn On your Jump Starter

  • Short press the power switch to turn on the device.
  • The LCD screen will turn on.
  • It will enter standby mode automatically if there is no operation within about 20 seconds.

LED Light

  • Short press the ON/OFF button to turn on the device.
  • Long press the ON/OFF button for more than 3 seconds to turn on the light mode.
  • There are three modes: illumination, SOS, and flash.
  • Short press the power switch button to change the lighting modes.
  • Press the power switch button for more than 3 seconds to turn off the light mode.

Dual USB Outputs

This portable jump starter is equipped with two USB outputs:

  • Output 1: 5V 2.1A
  • Output 2: 5V 2.4A/9V 2A/12V 1.5A

Use these outputs to charge your portable electronic devices such as phones, tablets, Bluetooth headphones, etc.

Start your Car

  1. Insert the plug of the smart clip completely into the jump starter.
  2. All symbols cycle light up from left to right.
  3. The LCD screen shows the current voltage of YA50 Jump Starter.
  4. Correctly clip the red and black clamps to the electrodes of the car battery (red to positive and black to negative).
  5. Start the vehicle.
  6. When the vehicle is started, remove the jumper cable from the vehicle battery immediately.
  7. If it does not jump start successfully, wait 1 minute before repeating the above steps.

Smart Clamp Protection Mode Indicators

Situation LCD Display
Low-voltage Protection Icon lights up, Buzzer sounds intermittently once a

second,
Current voltage value is displayed on the LCD.
High-voltage Protection| Icon flashes, Buzzer sounds continuously.
Reverse Charging Protection| Icon lights up, Icon flashes, Buzzer sounds intermittently once
a second.

Package Content

YaberAuto-YA50-Car-Battery-Jump-Starter-FIG-
\(1\)

Introduction

Thank you for purchasing YaberAuto YA50 car jump starter. Please read the user manual carefully before you start to use the product

Key Features

  1. Powerful Car Battery Jump Starter: YaberAuto YA50 Car Jump Starter can jump start a 12-volt car, SUV, or truck in seconds up to 30 times with high peak current and heavy-duty clamps.
  2. Portable Power Bank: With dual USB charge ports (one compatible with fast charging), it can quickly charge numerous portable devices, such as smartphones, tablets, cameras, Bluetooth headphones and more.
  3. All-Round Protection: With all-round protection, such as short-circuited protection, over-current protection, overload protection, over-voltage protection and so on, it can safely jump starter your vehicle without the worry of incorrect connections or sparks.
  4. Multi-Function: This jump starter is also equipped with a LED flashlight with 3 modes (illumination, SOS, flash) and a accurate compass that can be used in emergency situations.
  5. What You Get: ① YaberAuto YA50 Car Jump Starter ② Smart Jumper Cables ③ Charging Cable ④ Storage Case ⑤ User Manual

Know Your Product

YaberAuto-YA50-Car-Battery-Jump-Starter-FIG-
\(2\)

  1. ON/OFF
  2. Input Port
  3. Output 1
  4. Output 2
  5. Jump Starting Port
  6. LCD
  7. Compass
  8. LED Light

Powerful circuit protection system – Smart ClampsYaberAuto-YA50-Car-
Battery-Jump-Starter-FIG- \(3\)

  1. Red jumper cable (+)
  2. Black jumper cable (-)
  3. “Smart Clamp” plug
  4. Digital LCD Screen

Getting Started

Charging your Jump StarterYaberAuto-YA50-Car-Battery-Jump-Starter-FIG-
\(4\)

  1. Please use a 5V 2A / 9V 2A adapter to charge the product. (adapter is not included)
  2. It will take approximately 6 hours to fully charge the unit when using a 5V/2A adaptor. In order to extend the battery life, please charge the unit every 3 months.

Turn On your Jump Starter

Short press the power switch to turn on the device, and the LCD screen will turn on. For energy saving, it will enter standby mode automatically if you have not operation within about 20 seconds

LED Light

Short press the ON/OFF button to turn on the device and then long press the ON/OFF button more than 3 seconds to turn on the light mode. There are three modes (illumination, SOS and flash). You can simply short press the power switch button to change the lighting modes. And you can also press the power switch button for more than 3 seconds to turn off the light mode.

Dual USB Outputs

This portable jump starter is equipped with two USB outputs (Output 1:5V 2.1A, Output 2: 5V 2.4A/ 9V 2A/ 12V 1.5A) that provide the fastest charging speed for your portable electronic devices, such as phones, tablets, Bluetooth headphones, etc.

Start your CarYaberAuto-YA50-Car-Battery-Jump-Starter-FIG-
\(5\)

  1. Insert the plug of the smart clip completely into the jump starter, All the symbols cycle light up from left to right; the LCD screen shows the current voltage of YA50 Jump Starter.
  2. Correctly clip the red and black clamps to the electrodes of the car battery (red to positive and black to negative)
  3. Start the vehicle.
  4. When the vehicle is started, remove the jumper cable from the vehicle battery immediately.
    Note : If it does not jump start successfully, please wait 1 minute before repeating the above steps.

YaberAuto-YA50-Car-Battery-Jump-Starter-FIG- \(6\)

You can read the LCD indicator when the smart clamp goes into protection mode in the following situtations.(25℃ )YaberAuto-YA50-Car-Battery-Jump-Starter-
FIG- \(7\)

Notes on Charging Your Car Battery

  1. Use the original smart clip to start the car.
  2. DO NOT use this unit if any cable clamp or cord is damaged.
  3. Start only for 12V vehicles,or it will cause serious damages to the unit.
  4. Don’t jump start your car when the battery capacity is lower than 50%.
  5. Do not connect two clamps together. And do not connect both cable clamps to the same piece of metal.
  6. If the engine does not start on the first try, disconnect it from the car battery and wait for at least 60 seconds before reconnecting. Maximize three attempts in 5 minutes.
  7. Once the engine is successfully started, please disconnect the clamps
Model YA50
Output1 5V 2.1A
Output 2 5V 2.4A/ 9V 2A/ 12V 1.5A
Input 5V 2A /9V 2A
Voltage 12 Volts
Jump Starts Per Charge Up to 30
Charging Temperature 0 ~ 40℃
Working Temperature -20℃ ~ 60℃
Product Dimensions 186mm×89mm×45.5 mm

FAQ & Trouble Shooting

  • Q: How to turn off this power pack?
    A: This power pack will power off automatically when no load or charging is complete.

  • Q: What kind of adapter should I use?
    A: You can use the charger of your phone or tablet.

  • Q: How long time to full charge the YaberAuto YA50 jump starter?
    A: About 6 hours through the 5V/2A AC adapter.

  • Q: How many times can this product start the vehicle with full capacity?
    A: Up to 30 times.

  • Q: What to do if my phone is failing to charge?
    A: Please try with another charging cable

Care and Maintenance

  • DO NOT put the product under direct sunlight or hot areas.
  • DO NOT drop or knock your car jump starter.
  • DO NOT disassemble the equipment, which may cause damage.
  • DO NOT use chemicals or detergents to clean the product.
  • DO NOT place the product in high temperature environment for long. (The Operating Temperature: -20~60℃ )
  • Please check the power of the product at least every three months, and charge the product in time

Warranty

Our company provides customers with warranty of 24 months from the date of purchase

Contact US

For additional assistance or warranty cover claim, please contact us:
E-Mail: support@yaberauto.com

FCC

Federal Communication Commission Interference Statement

NOTE : This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. This device must accept any interference received, including interference that may cause undesired operation.

Declaration of Conformity

We (Manufacturer is responsible for this declaration) Ekoo Electronic Co.,Ltd.
(Company name)
B09,block B,f2,bldg.b,runfeng Pioneer Park,no.973, minzhi Avenue, Minzhi St., Longhua, Shenzhen, CN (Company address) declare under our sole responsibility that the product

  • Trade name : YaberAuto
  • Equipment: Car Jump Starter
  • Model No. : YA50

To which this declaration relates is in conformity with the essential requirement set out in the Council Directive on the Approximation of the laws of the Member States relating to LVD Directive(2014/35/EU) & EMC Directive(2014/30/EU) & RoHS(2011/65/EU) product is responsible to affix CE marking, the following standards were applied:

  • EN 62368-1:2014+A11:2017
  • EN 55032:2015+A11:2020
  • EN 55035:2017+A11:2020
  • IEC62321-3-1:2013
  • IEC62321-4:2013
  • IEC62321-5:2013
  • IEC62321-6:2015
  • IEC62321-7-1:2015
  • IEC62321-7-2:2017
  • IEC62321-8:2017
  • Full Name: George.wang
  • Signature: George.wang
  • Position: Approbation Manager
  • Place/Date: Shenzhen,China/Aug.18-2021

Correct Disposal of this product

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals