YaberAuto YA70 Car Jump Starter User Guide

YaberAuto YA70 Car Jump Starter

Know Your Product

1. LED Screen
2. Lighting Button
3. Power Button
4. Switch Button (Inflation Mode Switch/Unit Switch)
5. Air Pressure Increase Button
6. Air Pressure Reduction Button
7. USB-C Input
8. DC Output
9. Output 1
10. Output 2
11. Jump-Start Port
12. LED Light
13. Air Hose Interface
14. “Smart Clamp” plug
15. Red Jumper Cable +)
16. Black Jumper Cable (-)
17. Indicator Light
18. Force Start Button

Charging Your Jump Starter

1. Please use the included USB-C charging cable and adapter (5V/2A and above) to charge the product. (adapter is not included)
2. It will take about 5 hours to fully charge the unit when using a 5V/2A adapter. To extend the battery life, please fully charge the unit every 3 months.
3. When using the product for the first time, please make sure the product is fully charged.

Powering Your Devices
This portable jump starter is equipped with dual USB outputs
(Output 1: 5V/2.4A Output 2: 5V/2.4A, 9V/2A, 12V/1.5A) that can quickly charge your portable electronic devices such as phones, tablets, etc.
LED Light
Short press the power button to turn on the device, then long press the lighting button for more than 3 seconds to turn on the light mode, then short press the lighting button to change the light modes in lighting, SOS, and Strobe. Long press the lighting button for more than 3 seconds to turn off the LED light.
Air Compressor
Built-in 150 PSI air pump, it supports 5 inflation modes: car inflation mode, motorcycle inflation mode, bicycle inflation mode, basketball inflation mode, and custom inflation mode; 3 kinds of unit switching, BAR, KPA, PSI.

How to Inflate Car Tires

1. Take out the device connect the air hose and tighten it, short press the power button to start the device, short press the power button again to enter the inflation mode,
2. Short press the switch button to select the inflation mode, long press the switch button to switch 3 kinds of units, press the “+” button / “- ” button to adjust the air pressure value,
3. Long press the power button to start inflation
4. Short press the power button or switch button , and it will automatically stop inflating.

Jump Start Your Car

1. Insert the plug of the smart clamp into the jump starter, the indicator light of the smart clamp will flash red and green alternately
2. Correctly clip the red and black clamps to the electrodes of the car battery (red to positive and black to negative), the indicator light of the smart clamp is always green.
3. Start the vehicle.
4. When the vehicle is started, remove the jumper cable from the car battery immediately.

Note

1. If it does not start successfully, please wait for 60 seconds and then repeat the above steps.
2. When using this product, please do not connect two clips. Otherwise, this product will be damaged.

Troubleshooting

Indicator Light Troubleshooting Guide

the clips are reversed, red to positive and black to negative
The red light is always on and the buzzer is always beeping| Please check whether the clips are connected or on the same metal conductor
The red light is always on, but the buzzer does not sound| Remove the clip from the car battery and reconnect it
The red light is always on, and the buzzer beeps quickly and briefly| Smart clip failure, please contact us to replace the smart clip

Error Message on Screen/ Cause/ Solution

• “E1 “- Low temperature charging protection: Stop charging, it will automatically release protection when the temperature rises above 2°C
• “E2” – High temperature charging protection: Stop charging, it will automatically release protection when the temperature is lower than 45°C
• “E3” – High-temperature discharge protection: Stop charging, it will automatically release protection when the temperature is lower than 65°C
• “E7” – Cylinder over temperature protection: Automatically release the protection when the temperature is lower than 70° C, After the protection is released, please wait for 10 minutes before continuing to operate.

Specifications

Package Content

• YaberAuto YA70 Jump Starter with Air Compressor 1 Gas Nozzles 3
• Air Pump Hose *1
• Smart Jumper Clamps *1
• USB-C Charging Cable *1
• DC Cigarette Lighter *1
• User Manual *1
• Portable Storage Bag *1

Maintenance

1. Do not use the product to start an already expanded car battery.
2. Inflate continuously for more than 1 O minutes. It is recommended to stop for 10 minutes and continue to use after the temperature of the machine drops!
3. When using this product, keep the surroundings well-ventilated, do not block the cooling holes, and do not use it in the following environments:
   • Damp places and places easily splashed by water.
   • A place where it is easy to drop.
   • A place subject to vibration, corrosion, dust, and chemical gas hazards.
   • A place where flammable and explosive materials are stored, and near a high-temperature heat source.
4. Check the battery level at least once every 3 months and recharge it in time.
5. Keep away from children and pets.

Warranty

• If there is any problem or failure during use, please send your question and order number to our email.
• We will provide you with good after-sales service within 24 hours.
• support@yaberauto.com.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>