XTOOL MXHP002 Smart Control User Manual
- June 12, 2024
- XTOOL
Table of Contents
Smart Control
User Manual
Statement
Thank you for choosing x Tool products!
If you use the product for the first time, read carefully all the accompanying
materials of the product to improve your experience with it. If you do not use
the product according to the instructions and requirements of the Manual, or
mis-operate the product due to misunderstanding, etc., the Company shall bear
no responsibility for any loss resulting therefrom.
The Company has collated the content of the Manual rigorously and carefully,
but errors or omissions may remain.
The Company is committed to continuously improving product functions and
service quality, and therefore reserves the right to change any product or
software described in the Manual and the content of the Manual at any time.
The Manual is intended to help you use the product properly and does not
include any description of hardware and software configuration. For product
configuration, refer to the related contract (if any) and packing list, or
consult your distributor. Images in the Manual are for reference only and the
actual product may vary.
Protected by copyright laws and regulations, the Manual shall not be
reproduced or transcribed in any way, or be transmitted on any wired or
wireless network in any manner, or be translated into any language, or be
modified in any way, such as content, image, or layout modification, without the
prior written authorization of the Company.
The Company is committed to continuously improving the product and related
materials. The product and the Manual are subject to change, and updates can
be found at xtool.com.
Safety first (important)
Read and get familiar with all safety precautions and measures before using
this product. Strictly follow all safety precautions. Ensure that this product
is properly assembled and is working properly.
Follow the operating principles:
- Check the product for damage every time before you use it. Do not operate it in any way when any damage or defect is found.
- Ensure that the workspace is clean and flat.
- Do not leave the product unattended during operation. Pay attention to whether it is working properly.
- The machine works properly at the temperature of –10℃ to 35℃ and can be stored at the temperature of –10℃ to 45℃. Do not operate it at a temperature lower than 0℃.
List of items
Specifications
| Size | 117.2 mm x 91.4 mm x 35.1 mm |
|---|---|
| Temperature setting range | 100℃ ~ 205℃ （212℉ ~ 400℉） |
| Time setting range | 0s ~ 600s |
x Tool Smart Control Transceiver
Model| MXH-P002a-001
Input| 5V ****100mA
Maximum RF transmit power| 2.4G(2420-2470MHz)< 20 dBm
FCC ID| 2AH9Q-MXHP002A
IC| 22796-MXHP002A
Meet your smart control
Preparations
Connect to a power supply
Pair with the Smart Control
Smart Control settings
- Switch between preset levels
Level| Temperature| Time
---|---|---
A| 140℃ （285℉）| 30s
B| 160℃ （320℉）| 30s
C| 195℃ （385℉）| 50s
D| 205℃ （400℉）| 60s - Define a level yourself
- Set the time and temperature directly
Use the device
The usage of the smart control may vary according to heat pressing devices.
Visit support.xtool.com or scan the following QR
code to find details about how to use x Tool devices with the smart control.
Error code description
| Error code | Description |
|---|---|
| Exceptions occur on the temperature sensor on the heating plate. | |
| The temperature sensor is damaged. | |
| The heating plate cannot be heated. | |
| The temperature of the heating plate does not go as expected. | |
| The temperature of the heating plate does not go as expected. | |
| Exceptions occur on the temperature sensor on the circuit board. | |
| The radiating fins are overheated. | |
| Exceptions occur when the heating plate is heated. | |
| Exceptions occur when the heating plate is heated. | |
| Exceptions occur when the heating plate is heated. | |
| Exceptions occur on the wireless chip. |
If you see any error code displayed on the screen, contact x Tool team for help.
How to charge the Smart Control?
Declaration of conformity
Hereby, Makeblock Co., Ltd., declares that this product is in compliance with
the essential requirements and other relevant provisions of Directive RED
2014/53/EU and the RoHS directive 2011/65/EU.
After-sales services
For technical support, contact us at
support@xtool.com.
For more information about after-sales services, visit
support.xtool.com.
FCC statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC radiation exposure statement(For Smart Control Transceiver)
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 cm between the radiator and your body.
RF warning statement:(For Smart Control)
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
This device complies with Industry Canada licence-exempt RSS standard( s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.”
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>