easee Plug and Play Black Wallbox User Guide

easee Plug and Play Black Wallbox

Product Information

• The Easee Plug & Play is a product that allows for easy installation and charging of electric vehicles. It requires a mobile device with NFC or Bluetooth support for installation and operation using the Easee App.
• Important product information and guidelines can be found in the product packaging or at easee.com/manuals.
• The product should only be installed, repaired, or serviced by an authorized electrician, following all applicable local, regional, and national regulations for electrical installations.
• The product includes a PIN code for installation, located on the front of the Chargeberry. It is recommended to keep the PIN code in a safe place.
• The front cover of the product protects the electronics from external influences. The front cover tool is provided for removing the front cover after removing the screw.

Technical Specifications

• Dimensions: Varies
• Drilling hole distance: Varies
• Operating temperature: Varies
• Weight: Varies
• Sensors and indicators: Light strip with LEDs showing charger status, touch button, temperature sensors in all main contacts
• Charging: Max charging power capacity of up to 7.36 kW at 32 A 1 phase, up to 22 kW at 32 A 3 phase, Type 2 socket (IEC 62196-2), load balancing of up to 101 units per circuit
• Connectivity: Built-in eSIM (LTE Cat M1/2G/GPRS), WiFi 2.4 GHz b/g/n connection, Easee Link RFTM, control charging via Easee App, RFID/NFC reader, OCPP 1.6 via our API
• Protection: Integrated overload protection according to EN IEC 61851-1:2019, built-in RCD for ground fault protection (30 mA AC/6 mA DC), degree of protection: IP54, impact resistance: IK10, insulation class: III, overvoltage category: I

Installation Instructions

WARNING: If the Easee Ready is installed in your private home, it is recommended to turn off the power before installing the Chargeberry. If turning off the power is not possible (e.g., in a shared charging system), exercise caution and
follow the instructions carefully.

Easee Ready Opening:

1. Unscrew the locking screw at the bottom of the Easee Ready.
2. Insert the two ends of the front cover tool into the two openings at the bottom of the Easee Ready cover.
3. Pull until the cover comes loose and lift the cover from the bottom and upwards.

Chargeberry Attaching:

WARNING: Insulation testing must be performed before installing the Chargeberry in the backplate. Testing the circuit insulation with the Chargeberry installed may damage the electronics or impact the reading negatively.

WARNING: Do not touch the electrical terminals or wires inside the backplate as they are electrically live.

For detailed installation guidance, we recommend watching the installation videos available on our website: easee.support.

Introduction

Read the Important product information guide in the product packaging or at easee.com/manuals before installing the product.
Installation of this product requires a mobile device with NFC or Bluetooth support. Operation of the product using the Easee App requires a mobile device with Bluetooth support.

WARNINGS AND CAUTIONS
A Warning indicates a condition, hazard or unsafe practice that can result in serious personal injury or death.
A Caution indicates a condition, hazard or unsafe practice that can result in minor personal injury or damage to the product.

WARNING
This product shall only be installed, repaired or serviced by an authorised electrician. All applicable local, regional and national regulations for electrical installations must be respected.

PIN code
The PIN code is required for installation and located on the front of the Chargeberry. It is recommended to keep the PIN code for safe keepings, e.g inside the fuse cabinet.

Product overview

• Front cover
  Protects the electronics from external influences.

• Chargeberry
  Contains the electronics for charging the vehicle.

• Front cover tool
  Used for removing the front cover, after the screw has been removed.

Technical specifications

Installation instructions

WARNING
If the Easee Ready is installed in your private home, we recommend that you turn off the power before continuing the process of installing the Chargeberry. If for some reason it is not possible to turn off the power – for instance, if the charger is part of a shared charging system – be careful and follow the instructions.

We recommend that you watch the installation videos available on our website: easee.support.

Easee Ready Opening

1. Unscrew the locking screw at the bottom of the Easee Ready.
2. Insert the two ends of the front cover tool into the two openings at the bottom of the Easee Ready cover.
3. Pull until the cover comes loose and lift the cover from the bottom and upwards.

Chargeberry Attaching

WARNING
Insulation testing must be performed before a Chargeberry is installed in the backplate. Testing the circuit insulation with the Chargeberry installed in the backplate may damage the electronics or impact the reading negatively.

WARNING
Do not touch the electrical terminals or wires inside the backplate, they are electrically live.

1. Turn on the power. The terminals of the backplates are now electrically live.
2. Remove the PIN code sticker and attach it to the inside of the fuse cabinet, or another safe location for storage.
3. Position the Chargeberry to fit into the slots on the backplate located in the center of the installation.
4. When the Chargeberry is in the track, press it forcefully down until you hear a “CLICK”.

Front cover Closing

Before closing the front cover, it is possible to lock the Chargeberry with a padlock (see Practical details).

1. Hang the front cover at the top of the backplate and let it fall into place.

2. Press the bottom of the front cover until you hear a click.

3. Bend the lower part of the rubber cover down.

4. Screw in the front cover screw at the bottom of the charger to secure the front cover.
   NOTE! The locking screw is necessary to secure the cover and protect the charger from exposure.

5. Close the rubber cover. If the cable is inserted from the bottom, you can cut a corresponding hole in the rubber cover to ensure a neat installation.
   The charger is now ready for testing according to local regulations. Once complete, transfer ownership to the owner via the Installer App.

Features

1. Touch button: The touch button is used to activate the local interface. The local interface is intended for local operations of the charger when no internet is available. Read more about the local interface at: easee.com/support/localinterface
2. Light strip: The light strip communicates the status of the Charging Robot at all times. (See Charging Robot interface).
3. RFID area: The integrated RFID reader enables access control of the Charging Robot and identification of different users. You can use it to unlock the charger with an Easee Key. Check our knowledge base at easee.support for more details on how to add and manage your Easee Keys.
4. Type 2 socket: The Type 2 socket is completely universal and allows you to charge any type of electric vehicle using the appropriate charging cable. Furthermore, it is possible to permanently lock the charging cable, so you do not have to worry about it being stolen.

How do I charge?

Read the Important product information guide in the product packaging or at easee.com/manuals before using the product.
Operation of the product using the Easee App requires a mobile device with Bluetooth support.
Make sure that the following requirements are met before using the Charging Robot:

• The product and its electrical connection has been installed by an authorised electrician according to the Installer guide.
• The charger is properly configured.
• The software is up to date (see the Charging Robot interface).
• If you have set up access control, unlock it by using a registered RFID tag (see the Features) or disable it from the Easee App or the local interface.

1. Check the charging cable and connector for damage and impurities such as foreign objects and water ingress before charging.
2. Connect the charging cable to the Charging Robot and your electric car. The charging process starts and adapts automatically to the electric car and the available energy at any time according to the configuration.

If the car does not start charging, check that charging is activated in your car and that the connectors are properly plugged in. If charging still does not start, check what might be the cause on the Charging Robot interface section.

Smart charging
Some operators offer smart charging which will delay charging to a suitable point in time, often tied to electricity price or similar mechanisms. When Smart charging is active the LED strip is lit blue, charging will not start until the operators criteria for charging is met. Contact you operator to know more and to find out if they offer this service.

Apps and interfaces

Easee App
The Easee App gives full control and status over your charger. It´s intended for everyday use of your Easee products, through the Easee Cloud.
To download the app, scan the QR code or go to: easee.com/app

Local interface
The local interface is intended for local operations of the charger when no internet is available.
Read more about the local interface at: easee.com/support/localinterface

Easee Portal
The Easee Portal is a tool intended for administration of one or several Easee sites. The Portal is mainly intended for site owners, installers, administrators, service providers and people who need to manage several products and sites from one interface.
Go to easee.support for more information on our interfaces.

Charging Robot interface

Maintenance

General maintenance

• Ensure that the charger does not have any signs of mechanical damage.
• Visually inspect the Type 2 socket for wear and tear at regular intervals according to local regulations. If the pins are discoloured or damaged, please contact your authorised electrician.

Cleaning
The product does not require cleaning to operate properly. Nevertheless, if the product needs to be cleaned for cosmetic reasons, this is possible.

• Use a damp cloth and an all-purpose household cleaner. Avoid using strong chemicals that contain oil or alcohol, as this will discolour the plastic.
• — Do not use running water or high pressure water jets.

Repair
If your charger needs to be repaired, please contact your Easee supplier.

Returns and complaints
Contact your distributor or Easee Customer Support regarding the return and complaint of your product.

Customer support
Download the latest manuals, find answers to frequently asked questions and useful documents and videos for your product at easee.support.

Practical details

Warranty
The device is free from material defects and is in accordance with laws and regulations for consumer protection in the country where the product is purchased. All correctly installed Easee hardware is covered by our 3 years limited warranty. If your charger needs to be repaired within this warranty period, please contact your Easee supplier. Further information can be found at easee.support.
Some countries may have extended warranty.

Padlock
It’s possible to lock the electronics with a padlock. This will create an extra layer of security (padlock is not included).

• Max total lock height: 56 mm
• Shackle height (outer dimensions): 19 – 20 mm
• Shackle thickness: 3.2 – 4 mm

Contact details
Easee ASA
Grenseveien 19
4313 Sandnes, Norway
Org. nr: 920 292 046
You can find additional contact details for your country at easee.com.

The information in this document is for information purposes only, is provided as is, and may be subject to change without notice. Easee ASA including its subsidiaries does not accept any liability for the correctness or completeness of the information and illustrations, and is not liable or responsible for your considerations, assessments, decisions or absence of such, or other use of the information in this document.
No part of this publication may be re-published, reproduced, transmitted or re-used in any other form, by any means or in any form, for your own or any third-party’s use, unless otherwise agreed with Easee or its subsidiaries in writing. Any permitted use shall always be done in accordance with good practice and ensure that no harm may be caused to Easee or by misleading the consumer.
Easee and Easee products, product names, trademarks and slogans, whether registered or not, are Easee’s intellectual property and may not be used without Easee’s prior written permission. All other products and services mentioned may be trademarks or service marks of their respective owners.
July 2023 – Version 1.01
© 2023 by Easee ASA. All rights reserved.

Easee ASA Grenseveien 19 4313 Sandnes, Norway www.easee.com

References

• Easee – Shaping the future of electricity
• Easee app | Easee International

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>