CRAFT MAIN CVSS6072-CS-BN Sliding S-Curve Shower and Tub Door Installation Guide

June 12, 2024
CRAFT MAIN

CRAFT-MAIN-logo

CRAFT MAIN CVSS6072-CS-BN Sliding S-Curve Shower and Tub Door

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-product-
img

READ THE INSTRUCTIONS CAREFULLY
Familiarize yourself with all the parts as shown in the exploded view. The exploded view will also provide a helpful reference when relating to the location of the various parts and how they are mounted.

PART LIST

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-1

PART

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-2

WARNING: Safety glasses should always be worn when working with tempered glass.

RECOMMENDED TOOLS

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-3

INSTALLATION PROCEDURE

STEP 1

Attach rollers to hanger clips on both panels. Rollers should be mounted so that the head of the mounting screw is on the same side of the panel as the screw head set into the hanger clip (see inset drawing). The inner panel must be on the same side of your shower as the shower head. If your shower head location requires you to reverse the panels, you will need to install the rollers on the opposite side of the hanger clip and flip the panels around to create the proper orientation. In this case, you should ignore the labels that say “rollers belong on this side”.
NOTE: The various holes in the hanger clip are used to fine-tune the adjustment of the panel to make up for walls that are slightly out of square or plumb. For best results start with all rollers in the second hole from the top and then make adjustments as needed.

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-4

STEP 2

  • Measure the opening on the bottom and cut the bottom track (2) 1/8″ shorter than the opening.

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-5

STEP 3 & STEP 4

Place the wall jamb down over the bottom track so that the back of the jamb is between the bottom track and the wall. Using a level to ensure the jamb is plumb, mark hole locations. Remove the jamb and drill holes about 1 1/2″ deep at each of the marked locations.
IMPORTANT NOTE: The middle holes pre-drilled in your wall jambs are NOT centered. When marking your holes and installing the jambs, be sure to position them so that the hole is closer to the bottom of the jamb than the top.
NOTE: When drilling into ceramic, glass or stone use a 1/4″ (6mm) MASONRY drill bit.
NOTE: When installing on fiberglass or acrylic use a 1/8″ (3 mm) drill bit and discard the wall plugs. When installing on fiberglass or acrylic the side jambs may need to be filed at the bottom to fit the contour of the unit.

  • Repeat 4 Step 3 on the other side.

STEP 5

  • Run a thin bead of silicone caulk down the entire length of both bottom ledges on the bottom track.
  • Place the bottom track into position and press down firmly along the length of the track.

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-7

STEP 6 / STEP 7

  • Push wall plugs into holes drilled in Step 3 and tap them in with a rubber mallet.
  • NOTE: If you are installing on fiberglass or acrylic, skip this step and discard the wall plugs.
  • Dab silicone into all 3 holes on each side. Run 1 1/2″ pan head screws through the wall bumper and use them to attach the wall jamb to the wall in the top and bottom holes only on both sides.

STEP 8 / STEP 9 / STEP 10

  • Use 1 1/2″ pan head screws to anchor the wall bumper and bumper guide into the center hole on each side.
  • Measure the opening at the top of the wall jamb, and cut the top track (1) 1/16″ shorter than the opening.
  • Place the top track down over wall jambs as shown.

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-8

STEP 11

  • Install the outer door panel by lifting it up & into a top track (1) (Do not lift by towel bar, be careful not to bump the panel against the metal track.)

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-9

STEP 12

  • Install the inner door panel by lifting it up & into a top track (Do not lift by towel bar).

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-10

STEP 13 / STEP 14

  • Install towel bars (5).
  • Position the panel guide in the center of the bottom track. Drill two 1/8″ holes through screw holes in the guide and into the bottom track. Position panels in guide as shown in inset drawing and attach the guide to bottom track using 3/8″ pan head screws.

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-11

STEP 15

  • Install a safe slider clip (9).
  • To install a safe slide clip, put the install bar into the clip and lift onto the clip hanger pull down leaving the clip in place.

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-12

FINAL STEP

  • Caulk both sides of the shower door frame to seal.
  • Keep the entire area dry for a minimum of 24 hours.

CRAFT-MAIN-CVSS6072-CS-BN-Sliding-S-Curve-Shower-and-Tub-Door-
fig-13

  • Please visit us on YouTube and view our shower door installation videos.
  • One may be available for your installation. www.youtube.com/c/CRAFTANDMAIN.

Toll-Free Customer Assistance

  • Monday-Friday, 7:30 a.m. To 5:00 p.m. CST
  • 1-888-620-3667 US Customers
  • 1-888-256-7551 Canada Customers
  • 6241 Northwind Parkway, Hobart, IN USA 46342
  • USA: www.craftandmain.com.
  • 5970 Chedworth Way, Unit B, Mississauga, Ontario, Canada L5R 4G5
  • CANADA: www.craftandmain.ca.
  • © 2022 FGI Industries, Ltd. | CRAFT + MAIN™ and logo designs are trademarks or registered trademarks of FGI Industries, Ltd.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals