HYPERGEAR Bunny Tracks Wireless Headphones User Manual
- June 12, 2024
- HyperGear
Table of Contents
HYPERGEAR Bunny Tracks Wireless Headphones User Manual
SPECIFICATIONS
- Audio Mode Button
- Previous Track Volume Down
- Play/Pause Answer/End Call
- Next Track Volume Up
- Power Switch
- microSD Card Slot
- Voice Microphone
- LED Indicator
- 3.5mm Aux Input
- Micro USB Charging Port
GETTING STARTED
Charging Your Headphones
NOTE: Fully charge your headphones before first use.
Connect to a USB power source using the included Micro USB charging cable.
? Charging
⚪ Fully Charged (approx. 2 hours)
Pairing Your Headphones
- Switch the headphones ON, and they will automatically enter Pairing Mode. The LED indicator will blink BLUE and RED to indicate that it is ready to pair.
- Open the Bluetooth menu on your phone, tablet, or computer. Enable searching for nearby Bluetooth devices.
- Select “Bunny Tracks” to pair your headphones.
Once connected, the LED indicator will blink BLUE every 7 seconds while on and in use.
Your headphones will automatically reconnect to your phone, tablet, or computer the next time you turn your headphones on.
If you wish to pair your headphones to a different phone, tablet, or computer,
find your headphones in your device’s Bluetooth
menu and select “Forget This Device” or “Forget”.
INSTRUCTIONS
MP3 Mode
Insert a microSD card into the microSD card slot.
Long Press the MODE button to enter MP3 Mode.
To exit MP3 Mode, Long Press the MODE button again.
FM Radio Mode
To enter FM Radio Mode, Long Press the MODE button.
Long Press the ▶|| button to scan and memorize all available FM radio
channels.
Use the | ◀◀ and ▶▶ | buttons to change channels.
To exit FM Radio Mode, Long Press the MODE button again.
Aux Mode
Use a 3.5mm aux cord to connect the headphones to other audio sources,
including non-Bluetooth devices. Your music will
automatically play.
NOTE: When wired in, the headphones power off to save battery, and LED and Bluetooth functions are automatically disabled. Use the audio controls on your source device instead.
Need help? Visit www.myhypergear.com for additional product information or email info@myhypergear.com
IMPORTANT
Read all safety instructions and warnings prior to using this product Improper use and failure to follow safety guidelines could result in damage, excess heal, logic runes, fire, explosion, electrical shock, or other hazards causing serious and/ or tattle injury and/or property damage that is not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.
-
Permanent hearing loss may occur it you listen at high volumes. Set the volume to a safe level.
-
Maintain volume levels that allow you to hear sound round you and be alerted to potentially hazardous situations.
-
Do not store the device in a depleted state. Buttery cells may be damc1ged. Charge your unit at least once every 3 months even when not in use.
-
Do not store at extreme tompcraturos (below 40° For above 90° F). Battery cells may be damaged.
-
Recharge your device with the included Micro USB charging cable or a certified 3rd party cable and a 1A charging adapter. Is powerful adapters may charge Lee baler too slowly and damage/overheat the battery or cause a fire heard.
-
Unit is not waterproof. Do not submerge or expose to corrosive materials. Do not clean with harsh chemicals, soaps, or detergents.
-
Do not attempt to modify, disassemble, or repair this product.
-
Avoid excessive drops, bumps, and abrasions.
-
If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
-
If you find this product rapidly increasing in temperature, emitting odor, deformed, abraded, or demonstrating an abnormal
phenomenon, discontinue use immediately. -
Disposal of the unit in the garbage is unlawful under state and federal environmental laws and regulations.
Contact info@myhypergear.com to submit a
warranty claim.
Proof of purchase is required.