king KCV Series Cove Heater Instruction Manual
- June 12, 2024
- KING
Table of Contents
king KCV Series Cove Heater
Product Information
The KCV SERIES Cove Heater is a maintenance-free heater designed for
efficient heating in various spaces. It is available in both 240 Volt and 120
Volt options, and it is important to ensure that the electrical power supply
matches the voltage of the heater being installed. Using the wrong voltage can
significantly affect the heater’s performance and may even damage the unit.
The heater comes with a (2) year warranty from the date of installation, and
it is recommended to refer to the manufacturer’s warranty statement for
further details.
Product Usage Instructions
- Before starting any installation, maintenance, or repairs, ensure that the power source supplying the heater is turned off. Lock or tag the circuit breaker/fuse panel door to prevent accidental power supply.
- Make sure to follow local codes and ensure proper grounding of the heater.
- Remove the heater from its packaging and disassemble the aluminum heating panel from the back support frame. Remove the knockout in the junction box for the electrical supply connection.
- To install the back support frame on the wall, locate the studs and use existing mounting holes or pre-drill 3/16″ holes as needed. Securely mount the frame to the wall using appropriate fasteners.
- Temporarily hang the aluminum heating panel from the top lip of both junction boxes. This will provide support while making electrical connections.
- Connect the supply cable grounding wire to the green wire pigtail in the wiring compartment.
- Follow the desired wiring diagram provided and use the approved wire nuts to connect the power supply to the heater.
- After attaching the wires, push them inside the box and replace the end caps.
- The heater can be wired from either side, but power wires should be connected on one side only.
- In the opposite junction box, connect the white and black element wires together using an approved wire nut.
It is important to follow these instructions carefully to ensure the safe and proper installation of the KCV SERIES Cove Heater. Save these instructions for future reference.
DANGER & ELECTRIC SHOCK OR FIRE HAZARD
READ ALL WIRE SIZING, VOLTAGE requirements, AND SAFElY DATA TO AVOID PROPERlY
DAMAGE AND PERSONAL INJURY
WARNING
It is extremely important to verify the electrical power supply is the same
voltage as the heater being installed. 240 and 120 Volt heaters are not
interchangeable. Powering a 240-volt unit with 120-volt supply wires will
reduce heater output by approximately 75%. Powering a 120-volt unit with
240-volt supply wires will destroy the heater and voids all guarantee and
warranties.
CAUTION: Turn off the power source supplying the heater before attempting any installation, maintenance, or repairs. Lock or tag the circuit breaker/fuse panel door. Failure to do so could result in serious electrical shock, burns, or possible death.
WARNINGS: To ensure proper operation of this heater it should be a minimum of 6 feet above the floor and no closer than 2½” below the drywall ceiling (6” vinyl or drop ceilings). Draperies should clear the front and the top of this heater by 6”. Draperies hung below the heater should have a 2½” clearance. Do not block the heater in any manner. Never paint the heater.
MAINTENANCE & WARRANTY
Following the guidelines herein listed will result in a maintenance-free heater. There are no moving parts or motors to maintain. Periodic dusting of the front panel is all that is suggested. The KCV Cove Heater carries a (2) year warranty from the date of installation. Please refer to the manufacturer’s warranty statement for further information
GENERAL INFORMATION
Cove heaters are completely assembled and pre-wired. To prepare the heater for installation, carefully check the voltage to be used is the same as stated on the rating nameplate. Operating voltage can not exceed 5% of nameplate voltage. Operating heater with the above-listed voltage ratings voids all guarantees and warranties
INSTALLATION INSTRUCTIONS
Following are some general guidelines:
- Do not recess this cove heater.
- Disconnect power at the main panel.
- Make certain all wiring is in accordance with all local codes and units are properly grounded.
- The voltage rating of the heater should be the same as the supply load.
- Do not install the heater on vinyl wall coverings
Remove the heater from the carton. Disassemble the aluminum heating panel from the back support frame. Remove knock-out in junction box for electrical supply connection. See Figure A & B.
-
To install the back support frame on the wall, locate the studs in the wall and use existing mounting holes or pre-drill 3/16” holes as needed. Use appropriate fasteners to securely mount to the wall.
-
See Figure B. Temporarily hang the aluminum heating panel from the top lip of both junction boxes.
-
This will support the heater while the electrical connections are made and allow one person to wire the heater without having to hold the panel at the same time. See Figure C.
-
Connect the supply cable grounding wire to the green wire pigtail in the wiring compartment.
-
Follow the desired wiring diagram, to connect the power supply to the heater using approved wire nuts. Instructions for left or right side wiring
-
The heater can be wired from either side – wire one side only.
Caution: Power wires should be connected on one side only. -
in the opposite junction box, connect the white and black element wires together using an approved wire nut. See Figures D and E. After the wiring is complete, carefully press the electrical wires into the junction box, making sure not to pinch any wires between the junction box and the heating panel.
-
Install the end caps: Push the bottom edge of the aluminum heating panel towards the back panel, while installing the end caps, and lightly tighten the 2 screws to secure it. Do Not Overtighten, as the aluminum heating panel will expand and contract during heating, requiring it to move freely. See Figure F.
CAUTION
The heater should not be covered or blocked in any manner.
KING ELECTRICAL MFG. COMPANY 9131 10TH AVENUE SOUTH SEATTLE, WA 98108 PH:
206.762.0400 FAX: 206.763.7738 www.king-electric.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>