marta MT-IR1212A Steam Iron User Manual

STEAM IRON
User manual
MT-IR1212A

DESCRIPTION

Parts list

1. Spray nozzle
2. Water filling inlet
3. Steam control dial
4. Burst of steam button
5. Spray button
6. Power cord protector
7. Water tank
8. Temperature control dial
9. Soleplate

GBR Real set of the appliance could be different from listed in the User manual. Check once buy.
GBR USER MANUAL
CAUTION
Read this manual carefully before using the appliance and save it for future reference.

• Before the first use, check the device specifications and the power supply in your network.
• It is not intended for industrial use.
• For indoor use only. Use only for domestic purposes according to the instruction manual.
• Do not use with damaged cord, plug or other injuries.
• Keep the power cord away from sharp edges and hot surfaces.
• Do not pull the cord. Always take the socket. Do not reel the cord around the device housing.
• Never attempt to frame and repair the appliance by yourself. If you meet problems, please contact the nearest customer service center.
• Using accessories or replacement parts that are not recommended or sold by the manufacturer may cause damage to the appliance.
• Always unplug the appliance and let it cool down before cleaning and removing parts. Keep unplugged when not in use.
• To avoid electric shock and fire, do not immerse in water or other liquids. If this occurs, immediately unplug it and contact service center for inspection.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Place steam iron on the ironing board carefully.
• Be careful do not touch metal parts of working surface and water tank during operation.
• Avoid of ironing zippers, rivets, etc., as they can scratch soleplate.
• Do not place steam iron on the metal or rough surface.
• Move steam iron carefully to avoid burns, because of there could be hot water leakage, as well as hot steam.

USING THE APPLIANCE

SETTING TEMPERATURE

• Sort the fabric: wool with wool, cotton with cotton, etc. Start ironing the fabrics requiring the lowest temperature and progress to the higher ones, because the steam iron heats up quicker than it cools down.
• If the fabric consists of various kinds of fibers, start ironing the fabrics requiring the lowest temperature (e.g. article consisting of 60% polyester and 40% cotton should be ironed at the temperature indicated for polyester (•) and without steam.
• Turn the temperature control dial round until it is opposite the setting pointer.

ANTI-CALC SYSTEM
A special filter inside the water reservoir softens the water and prevents scale build-up in the plate. The filter is permanent and does not need replacing.
NOTE: Use tap water only. Distilled water makes the anti-calc system ineffective by altering its physicochemical characteristics.
Do not use chemical additives, scented substances or decalcifiers.
FILLING THE WATER TANK

• Unplug the steam iron before filling.
• Make sure that both the Steam Control turning Knob and Temperature Control Dial are in “OFF” position.
• Hold the steam iron in the horizontal position.
• Slowly pour water into the water fill opening.
• Do not fill higher than indication “МАX” of the water tank, in order to avoid spilling out of water.
• If you have to refill while ironing, unplug the appliance from the power supply before filling.

EMPTYING THE WATER TANK
The water tank should be emptied after each use.

• Unplug the steam iron from the power supply.
• While the steam iron is still warm, hold the steam iron over a sink and allow the steam iron to drain by tipping the point of the steam iron down
• Gently shake the steam iron to loosen any water drops that may be trapped. The warmth of the iron should dry out any remaining water.
  NOTE: If you empty the water tank after the steam iron has cooled down, set the steam iron in an upright position on its heel rest, plug it in and set the temperature to the maximum, heat for 2 minutes. Unplug the steam iron from the power supply.

SPRAYING

As long as there is enough water in the water tank, you may use the spray button at any temperature setting either on steam or dry ironing.

• Press the spray button several times to activate the pump while you are ironing.

STEAM IRONING

• With the unit unplugged, fill the steam iron with water.
• Stand the steam iron on its heel rest in an upright position on an iron-safe surface and plug in.
• Set the temperature to the maximum.
• Switch-on the steam control, setting the steam controller in steam position.
• When the light indicator is off, the steam iron has reached the desired temperature.
• When finished, unplug the appliance from the power supply.
  CAUTION: Avoid coming in contact with escaping steam.

DRY IRONING

• The steam iron can be used on the dry setting with or without water in the water tank, however it is best to avoid having the water tank too full of water while dry ironing.
• Set the steam control switch to the ‘0’’ position.
• Stand the steam iron on its heel rest in an upright position on an iron-safe surface and plug it in.
• Select the temperature best suited for the fabric to be ironed.
• When the light indicator is off, ironing may commence.
• When finished, unplug the appliance from the power supply.
  CAUTION: If the steam iron has been used for a long time, is hot and there is no water, do not refill it with water until the steam iron has cooled down.

STEAM BURST
Make sure that there is enough water in the water tank.

• Stand the steam iron on its heel rest in an upright position on an iron-safe surface and plug it in.
• Set the maximum temperature.
• Press the steam button.
  CAUTION: Hold the steam button pressing not more than 5 seconds to avoid hot liquid leakage. Stop the emission when the pilot light turns on, then start ironing again only after the pilot light has turned off.

CLEANING

• Before cleaning the steam iron ensure it is unplugged from the power supply and has completely cooled down.
• Clean the exterior with a damp cloth and wipe dry.
• Do not use abrasive cleaners.

STORAGE

• Unplug the steam iron from the power supply and allow cooling down completely.
• Empty the water tank after each use, and then wrap the cord around the heel rest.
• To protect the soleplate, place the steam iron in an upright position on its heel rest.

SPECIFICATION

Power supply: 230 V ~ 50 Hz
Manufacturer:
Cosmos Far View International Limited
Room 701, 16 apt, Lane 165, Rainbow North Street, Ningbo, China
WARRANTY DOES NOT APPLY TO CONSUMABLES (FILTERS, CERAMIC AND NON-STICK COATING, RUBBER SEALS, ETC.)
Production date is available in the serial number located on the identification sticker on the gift box and/or on sticker on the device. The serial number consists of 13 characters, the 4th and 5th characters indicate the month, the 6th and 7th indicate the year of device production. Producer may change the complete set, appearance, country of manufacture, warranty and technical characteristics of the model without notice. Please check when purchasing device. Made in China

References

• Multimarta - интернет-магазин бытовой техники MARTA

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>