marta MT-CO4900A Floor Air Cooler User Manual
- June 1, 2024
- MARTA
Table of Contents
AIR COOLER MT-CO4900A
User manual
Parts list
- Plastic cover for top water tank
- Control panel
- Air Inlet
- Air Outlet
- Display window for water level
- Stand
Real set of the appliance could be different from listed in the User manual.
Check once buy.
CAUTION
Read this manual carefully before using the appliance and save it for future
reference.
- Before the first use, check the device specifications and the power supply in your network. It is not intended for industrial use. For indoor use only. Use only for domestic purposes according to the instruction manual. Do not use with damaged cord, plug or other injuries. Keep the power cord away from sharp edges and hot surfaces.
- Do not pull the cord. Always take the socket. Do not reel the cord around the device housing. Never attempt to frame and repair the appliance by yourself. If you meet problems, please contact the nearest customer service center. Using accessories or replacement parts that are not recommended or sold by the manufacturer may cause damage to the appliance.
- Always unplug the appliance and let it cool down before cleaning and removing parts. Keep unplugged when not in use. To avoid electric shock and fire, do not immerse in water or other liquids. If this occurs, immediately unplug it and contact service center for inspection. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Do not touch running parts of the fan. Keep foreign objects away from running parts and grille. Do not block air inlets on the motor block. Do not use the fan without protective grilles.
BEFORE THE FIRST USE
For packaging reasons the fan was delivered unassembled. Do not connect the fan to the mains supply before you have completely finished the assembly. Please assemble the fan
USING THE DEVICE
Power
To operate the unit, press the ON/OFF button firstly, the unit will stand by;
press it again, the unit will be off.
Speed
When the unit stand by, to adjust the fan speed, press the SPEED button, the
fan speed setting will be adjusted as follows: 1=Low fan speed; 2=Medium fan
speed; 3=High fan speed;0FF=without fan speed Cool Mode
Once you select your fan speed, press the COOL button to ON, this will begin
the water circulation and begin the cooling/humidifying/air purifying process.
-
Lift the lid on the top of the unit and pour fresh water into the top water tank in order to fill the internal water tank with water.
-
Check the water level carefully, stop filling when the water level reaches the ‘MAX’ mark.
DO NOT overfill the water tank otherwise permanent damage may occur to the appliance. -
Check the water level during use to ensure that it does not fall below the ‘MIN’ mark and top up if necessary.
-
To enhance the cooling function, fill the Ice Bottles, replace the top and freeze them in the freezer. Once frozen, place one ice bottle into water tank to cool the water further.
Two ice bottles are supplied so that one can be in the top water tank cooling the water whilst the other is being frozen and then swapped over when the one in the water tank has defrosted. Ice box can store cool and slowly absorb the heating from water while ice boxes can make the temperature of water in the water tank less than it of the surrounding, so air cooler with frozen ice boxes can blow the cooler wind.
NOTICE: please take and put the ice boxes lightly, in order not to hurt the water recycling cooling system.
NOTICE: do not eat ice crystals in the box, and do not use the ice crystal box as a toy for children to prevent accidental ingestion. -
Press the Cool Button and press the Fan Speed Button to select either the high, medium, or low fan speed. DO NOT operate in the Cool mode without water in the internal water tank otherwise permanent damage may occur to the unit.
CLEANING AND MAINTENANCE
Emptying the water tank: First turn off and unplug the unit. Place the
unit either outside near a drain or alternatively on the sink drainer.
Carefully lift the unit up and remove the drain bung from the rear of the
cooler allow the water to drain out from the water tank. You can tilt the unit
at several angles to make sure all water is drained out from the unit. When
all the water is drained out you can put back the drain bung. Take care not to
tilt the unit over when full of water.
Cleaning the unit: First turn off and unplug the unit. Wipe the unit
housing with a neutral cleaner and a damp soft cloth. Use a dry cloth to dry
off the unit. Make sure unit is fully dry before using the unit.
Important: When clean the unit, the client must pull off the plug and cut
off the power while any part of control panel cannot be into water.
SPECIFICATION
Power supply
230 V ~ 50 Hz
Producer:
COSMOS FAR VIEW INTERNATIONAL LIMITED
Room 701, 16 apt, Lane 165, Rainbow North Street , Ningbo, China
Made in China
WARRANTY DOES NOT COVER SUPPLIES (filters, ceramic and non-stick coating,
rubber seals, etc.)
Production date is available in the serial number located on the
identification sticker on the gift box and/or on sticker on the device. The
serial number consists of 13 characters, the 4th and 5th characters indicate
the month, the 6th and 7th indicate the year of device production. Producer
may change the complete set, appearance, country of manufacture, warranty and
technical characteristics of the model without notice. Please check when
purchasing device. Current information about service centers is available on
the website https://multimarta.com/
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>