V-TAC VT-7508 LED Pendant Light Instruction Manual
- June 12, 2024
- V TAC
Table of Contents
VT-7508 LED Pendant Light
**Instruction Manual
**
TECHNICAL DATA
| MODEL | VT-7508 |
|---|---|
| SKU | 10341, 10342 |
| TOTAL POWER | |
| MODULE POWER | 5W |
TOTAL VOLTAGE/FREQUENCY
MODULE VOLTAGE| AC 200-240V, 50Hz
TOTAL CURRENT
MODULE CURRENT| 250 mA
LUMENS| 500 Im
COLOR TEMPERATURE| 3000K
BEAM ANGLE| 60°
CRI| >80
LIFE SPAN| 20,000 Hours
ON/OFF CYCLE| >15000
IP RATING| IP20
DIMENSION| 100×2000 mm
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the
best. Please read these instructions carefully before starting the
installation and keep this manual handy for future reference. If you have any
another query, please contact our dealer or local vendor from whom you have
purchased the product. They are trained and ready to serve you at the best.
The warranty is valid for 2 years from the date of purchase. The warranty does
not apply to damage caused by incorrect installation or abnormal wear and
tear. The company gives no warranty against damage to any surface due to
incorrect removal and installation of the product. The products are suitable
for 10-12 Hours Daily operation. Usage of product for 24 Hours a day would
void the warranty. This
product is warranted for manufacturing defects only.
MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages.
In case of any query/issue with the product, please reach out to us at:
support@v-tac.eu
For More products range, inquiry please contact our distributor or nearest
dealers.
V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul. L. Karavelow 9B
INSTRUCTIONS FOR THE LIGHT
- Please make sure to turn off the power before starting the installation.
- Installation must be performed by a qualified electrician.
- The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
- Proper grounding should be ensured throughout the installation.
- For Indoor Use only
**** This marking indicates that this product should not be disposed owith
other household wastes.
Caution, Risk of electric shock
*This product contains a light source of energy efficiency class
INSTALLATION DIAGRAM
WIRING DIAGRAM
Neutral Supply can be Blue or Black
Ground Supply Can be Green-yellow
Live Supply Can be Red or Brown
-
Switch off the power before starting the installation.
-
Use screws to fix mounting bar to the junction box.
-
Make the wire connections with connectors.
• Connect the live wire (L) from fitting to the live wire from main power supply.
• Connect the neutral wire (N) from fitting to the neutral wire from main power supply.
• Connect the earth wire from fitting to the earth wire from main power supply.
• Please pay close attention and make sure the wires are not exposed outside when wiring connections. -
Use screws to fix canopy to mounting bar.
-
Check if the installation is completed and turn on the power
Note : This light is designed with adjustable height, press the pin on the canopy to adjust the height of the light.
DIAGRAM FOR REPLACING THE LIGHT SOURCE
[BY PROFESSIONALS ONLY]
DIAGRAM FOR REPLACING CONTROL GEAR
[BY PROFESSIONALS ONLY]
| |
---|---|---
Replaceable Control Gear by a professional| Loosen the terminal base L and N
screws, and pull out the blue brown wire| Cut the terminal cap and remove the
driver.
| 
|
Connect the ‘+-’ pole of the driver with the ‘ + – ‘ pole of the main line,
then install the terminal cap with pliers.| Insert the blue brown wire of the
driver into the terminal base and use a screwdriver to lock the L and N
screws.|
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>