AV Pro edge AC-EX70-SC2-R A 70 Meter HDBaseT Receiver with our SC2 scaler built in User Guide

USER MANUAL
AC-EX70-SC2-R
A 70 Meter HDBaseT Receiver with our SC2 scaler built in FRESCO-SIX-A-GEN2

The AVPro Edge’s AC-EX70-SC2-R is the ideal solution for integrators that are needing to distribute a signal to a variety of displays and keep an optimal picture. Integrators  will enjoy it’s versatility of not only being able to control up/down scaling but handling EDID issues (including 4K HDR EDID’s) and being able to access audio from the  stream. This scaler is ready for future content as well as it’s able to distribute 18Gbps signaling. Yet if you have 480, 20, or 1080 displays the AC-SC2-AUHDGEN2 will make  sure it’s getting the right picture.

Typical Applications

• For mixed systems with SD, HD and UHD displays within a matrix. Since a matrix will typically “down-clock” to the lowest common format, putting a scaler in will  essentially “trick” the matrix into sending 4K UHD material. The scaler will downscale the content to 480 for the HD display.
• As an Audio Extractor – Stand-alone audio extractors cost about the same thing, so purchasing the AC-SC2-AUHD which does so much more, is a no brainer.
• EDID causes about 80% of HDMI connectivity issues – TheAC-EX70-SC2-R can fix them all.
• EDID capture and emulation – would you like to test end points prior to hanging that 600 pound projector 100 feet up on the ceiling? Use the AC-EX70-SC2-R and your problem is solved

Features

• HDMI 2.0(a/b)

• Fixed Output Options 480P, 720P, 1080P & 4K

• Adaptive Scaling Mode

• Plug & Play Match Display Preference Mode

• 16EDID Options (Including Auto & HDR EDID Options)

• L/R Audio De-embedding (PCM only, DOES NOT DOWNMIX)

• Test Pattern Generation

• Simple, easy to use. 3-Button Operation

• 18Gbps Bandwidth Support

• Up to 4K60 4:4:4 Support

• Full HDR Support (HDR 10 & 12 Bit)

• HDR, HDR10+ and HLG Support

• EDID Management and EDID emulate

• 720P, 1080P & 4K Test Patterns built in for troubleshooting

• HDCP 2.2 (and all earlier versions supported)

• CEC Pass Through

• 3D Support

• LED Status, Link, Power indication lights

• Micro USB port for control

• Supports uncompressed PCM 2- Ch., LPCM 5.1 & 7.1,
  Dolby Digital, DTS, Dolby TrueHD, DTS HD-Master Audio, Atmos on HDMI

• Can Cascade

What’sintheBox?

• AC-EX70-SC2-R
• 48V 1A Power Supply
• Mounting Brackets
• IRRX&TX
• Terminal Connectors

VIDEO:
VIDEO RESOLUTIONS UP TO 4K 60HZ 4:4:4

VESA RESOLUTIONS
HEIR FORMATS/RESOLUTIONS| UP TO DCI 4K (4096X2160)
420, 422, 444 (10 AND 12 DEEP COLOR) HDR10, HDR101-, HLG
COLOR SPACE| YUV (COMPONENT), ROB
(CSC: REC. 601, REC. 709, BT2020 DCI, P3 D6500)
CHROMA SUBSAMPELING| 4:t4, 4:2:2, 4:2:0 SUPPORTED
DEEP COLOR AUDIO:
AUDIO FORMATS SUPPORTED HDMI| UP T016 BIT (1080P) UP T012 BIT (4K)
PCM 2.0 CH. LPCM 5.1 & 71 DOLBY DIGTAL, DTS 5.1. DOLBY DIGITAL PLUS. DOLBY TRUEHD, DTS-HD MASTER AUDIO, DTS-X, DOLBY ATM OS
AUDIO FORMATS SUPPORTED EXTRACTED (2 CH PORT)| PCM 2 CH (NO DOWNMIX)
AUDIO FORMATS SUPPORTED EXTRACTED (DIGITAL TOSLINIO SCALING:
FIXED OUTPUT OPTIONS
(SCALES ALL INPUT FORMATS TO THE SAME)| PCM 2 CH (NO DOWNMIX)
480P 60HZ, 720P 60HZ, 1080P 60HZ, 1920X1200 (VESA), 4K 30HZ, 4K6OHZ YUV 4:2:0, 4K60HZ, AUTO (SINK DEVICE HID) SEE MANUAL FOR MORE INFO
FRAMERATE COVERSION| YES
INTERLACED-> PROGRESSIVE CONVERSION| YES
TEST PATTERN GENERATOR DISTANCE:
HDBASET (CAT) DISTANCE (4K)| YES
70 METERS / 230 FEET (CAT 6A)
HDMI LEAD IN/OUT (41(60 4:4:4)| UP TO 50 FEET (USING BULLET TRAIN HDMI)
HMI LEAD IN/OUT (W/ AOC CABLE) (4E60 4:4:4) OTHER:
BANDWIDTH| UP TO 130 FEET (USING BULLET TRAIN AOC) 18 GBPS
HDCP PORTS:
HDMI| HDCP 2.2 AND EARLIER TYPE A
HDBASET| 8145
AUDIO (EXTRACTED ANALOG)| 5 PIN TERMINAL BLOCK (BALANCED)
AUDIO (EXTRACTED DIGITAL)| OPTICAL TOSLINK
IR TX| 3.5MM MONO (2 CONDUCTOR)
IR RX| 3.5MM MONO (3 CONDUCTOR)
RS232| 3 PIN TERMINAL BLOCK
POWER ENVIRONMENTAL:
OPERATING TEMPRATURE| 2 PIN TERMINAL BLOCK
23 TO 1257 (-5 TO ro
STORAGE TEMPERATURE| -4 TO 140’F (-20 TO 60C)
HUMIDITY RANGE POWER:
POWER CONSUMPTION (TOTAL)| 5-90% RH (NO CONDENSATION)
24 WATTS MAX
POWER SUPPLY DIMENSIONS:
DIMENSIONS (UNIT ONLY LENGTH/WIDTH/HEIGHT)| INPUT: AC 100-240V – 50/60HZ OUTPUT: DC 48V lA
MM: 107.92 X 184.15 X 28.1 INCH: 4.25 X 7.25 X 1.11
DIMENSIONS (PACKAGED LENGTH/WIDTH/HEIGHT) (KIT)| MM: 184.2 X 316 X 79.5 INCH: 7.25 X 12.44 X 3.13
WEIGHT (UNIT)| 0.7 LBS (0.32 KG)
WEIGHT (PACKAGED) 1.4 LBS (0.64 KG)
‘SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE. MASS & DIMENSIONS ARE APPROXIMATE

Overview Top/Front

Overview Back

OUTPUT TIMING
The AVPro Edge’s AC-EX70-SC2-R is the ideal solution for integrators that are needing to distribute a signal to a variety of displays and keep an optimal picture. Integrators  will enjoy its versatility of not only being able to control up/down scaling but handling EDID issues (including 4K HDR EDID’s), image enhancement, and being able to  access audio from the stream. This scaling Receiver is ready for future content as well as it’s able to distribute 18Gbps signaling. Yet if you have 480, 720, or 1080 displays the AC-EX70-SC2-R will make sure it’s getting the right picture.

OUTPUT TIMING|
---|---
LEDs| 0000
OVF BYPASS| 0000
480P 60HZ| 1000
720P 60HZ| 100
1080P 60HZ| 1100
1920X1200 (VESA)| 0010
4K 30HZ| 1010
4K 60HZ YUV 4:2:0| 0110
4K 60HZ| 1110
AUTO (SINK DEVICE EDID)| 0001
“ADAPTIVE MODE”| 1001

ADAPTIVE MODE – Anything below 1080p will be automatically up converted to 1080p.
1080p and above will be left untouched.

EDID Settings

With EDID Settings you can manage the sources devices and force a certain output. This is especially important on newer sources that rely on EDID communications in  implement high bandwidth and HDR signals.

• 1080 EDIDs – Legacy EDIDs, these will ask the sources (especially high bandwidth ones) to output 1080 to function in 1080 Systems.
• 4K30 EDIDs – Asks the sources to output 4K30 and/or 4K60 4:2:0 (Ideal to force source device to work on common extension infrastructure that are less than 10G  like HDBaseT)
• 4K60 EDIDs – Asks the source to output 4K60 4:4:4 or signals above 9G
• HDR EDIDs – When you see HDR in the EDID, the EDID will ask the source to send HDR regardless of resolution.
• USER EDID – If you press and hold the EDID SETTINGS button for 2 seconds while connected to a display that’s powered on the SC2 will copy and store the  displays EDID here.

EDID SETTINGS

LEDs| 5678
EDID BYPASS| 0
1080P 2CH| 1000
1080P 2CH 3D| 100
4K 30HZ 2CH 3D| 1100
4K 30HZ 6CH 3D| 10
4K 60HZ 2CH 3D| 1010
4K 60HZ 6CH 3D| 110
4K 60HZ 8CH 3D| 1110
1080P 2CH HDR| 1
1080P 2CH 3D HDR| 1001
4K 30HZ 2CH 3D HDR| 101
4K 30HZ 6CH 3D HDR| 1101
4K 60HZ 2CH 3D HDR| 11
4K 60HZ 6CH 3D HDR| 1011
4K 60HZ 8CH 3D HDR| 111
USER EDID| 1111

Test Patterns
There are four built in Test patterns available
To Enable and Disable press “TEST” button to cycle through the 3 resolutions.

TEST PATTERN

LEDs| 9 10 11
OFF| 000
720P| 001
1080P| 010
4K 30Hz| 011
4K 60Hz| 100

You can also send the commands
SET OUTx SGM EN/DIS : Set Output Signal Generator Enable/Disable{x=[1]}
SET OUTx SGMT y : Set Output Signal Generator Timing
{x=[1],y=[0~3](0=720p 60Hz,1=1080p 60Hz,2=4K 30Hz,3=4K 60Hz}

 CTRL/ISP

1. Micro USB Port for firmware and control.
2. Command list below.
   For CTRL, use a Micro to USB cable and set the serial communications to: 57600,n,8,1 (baud: 57600, no parity, 8 data bits and 1 stop bit) with no handshaking.

GET INx SIG STA
SET OUTx VFMTy| Get Input x Signal Status{x= [1])
Output Setup Commands
Set Output x Video Timing Format
{x=[1], y=[0-8](0=BYPASS, 1=480P60Hz, 2=720p6OHZ, 3=1080P60hZ, 4=1920x1200RG8Hz,
5=4K30Hz, 6=4K60HzY420, 7=4K60Hz, 8=Self Adapt, 9=Advanced Bypass)).
SET OUTx SGM EN/ DIS| Set Output Signal Generator Enable/ Disable{x=[1]}
SET OUTx SGMT y| Set Output Signal Generator Timing
(x=[1], y=[0a,2](0=1080p 60Hz, 1=4k 30Hz, 2=720p 60Hz
SET OUTx EXA EN/DIS| Set Ex-Audio Output Enable/Disable{x=[1]}
SET OUTx STREAM ON/OFF| Set Output x Stream ON/OFF{x=111}
GET OUTx VFMT| Get Output x Video Timing Forma{x=[1]}
GET OUTx SGM| Get Output Signal Generator Status{x=[1]}
GET OUTx SGMT| Get Output Signal Generator Timing Status{x=[1]}
GET OUTx EXA| Get Ex-Audio Output Enable/Disable Status{x=[1]}
GET OUTx EDID DATA| Get Output x EDID DATA{x= [1])
GET OUTx STREAM SET Dix EDID y| Get Output x Stream ON/OFF Status{x=[1]}
Input Setup Commands Set Input x EDID{y=[00/15]}| O:EDID_BYPASS
1:1080P_2CH| 2:1080P_3D_2CH| 3:41C0Hz_3D_2CH
4:41a0Hz3D_6CH| 5:41c60Hz_3D_2CH| 6:4k60Hz_3D_6CH
7:41c60Hz_3DJICH| 8:1080P_2CH_HDR| 9:1080P_3D_2CH_HDR
10:41‘30itz_3D_2CH_HDR| 11:41C0Hz_3D_ECH_HDR| 12:41c6Oitz_3D_2CH_HDR
13:41(60Hz_3D_6CH_HDR| 14:41(60Hz_3D 8CH_HDR| 15:User EDID
SET Dix EDID CY OUTy| Copy Output y EDID To Input x(USER1 BUF){x=[1], y=[1])
SET INx EDID Uy DATAz| Write EDID To User y Buffer of Inpubc{x=[1], y=[1], z=[EDID Data]}
SET INx 17 POEy| Set In x POE Mode{x=[1],y=[0,4](0=Auto, 1=Force)}
GET INx EDID| Get Input x EDID Index{x=[1]}
GET INx EDID y DATA| Get Input x EDID y Data{x=[1], y=[0,45]).
GET INx TP POE SET APR MODEx WPzz| Get In x POE Mode Status{x=[1]}
Aspect Ratio Mode Setting
Set Aspect Ratio Mode x With Param zz{x=0-41,0=Normal Mode,[1-3]=Aspect Ratio Model-3,[4]-Aspect Ratio User Mode4},
NOTE:Mode0-3[zz==0x00] Mode4(zz={0x00-0x2F}]
GET APR MODE SET CPT MODEx| Get Aspect Ratio Mode x With Param Status
Captor Mode Setting
Set Captor Mode x{x=[0-5],0=Captor Mode OFF,[1-3]=Captor Mode 1-3 [4-5]-Captor User Mode4-5}
SET CPTMx CDT x0.y0.x1.y1| Set Captor Mode x Coordinate x0.y0.xl.y1 (x=r1-5],x08m1=[0-1920],y0841=[0- 1080],Notelx0<x1][y0<y1])
GET CPTMx CDT| Get Captor Mode x Coordinate Status{x=(1-5]}
GET CPT MODE SET OSD INF PAM x.y.c.z.b.t| Get Captor Mode Status
OSD Show Information Sett
Set OW Info Param:Position{x=[1-960],y=[1-540]},Color{c=[0-5]},Font Mode{z=[0-2]} {Background Color{b=[0-5]}, Background Transmittance Level{t=0-7} {c/b=[0-Black,l-White,2-Red,3-Green,4-Blue,5-Yellow],
SET OSD SHOW INF x| Set OSD Show details Info x[0-3]{0-0SD OFF,1-Show Input Info,2-Show Output EDID 3- Show Operating Information}
GET OSD INF PAM| Get OSD Info Param
GET OSD SHOW INF| Get OSD Show details Info

WITH THE AC-EX70-SC2-R YOU ARE ABLE TO DE-EMBED AUDIO AND UPSCALE A SIGNAL AT THE SAME TIME.

THE AC-EX70-SC2-R CAN GIVE THE SINK ANY RESOLUTION FROM 480P TO 4K 60 NO MATTER WHAT THE SOURCE IS OUTPUTTING

Troubleshooting

• Verify Power – When power is applied all lights on the front of the device will flash. You can also press any of the 3 buttons on the side to change settings, the  corresponding lights should change if the unit is powered up.
• Verify Connections – Make sure all connected cables are properly connected.
  • You can use the built in Test Pattern Generator to verify signal path from AC-EX70-SC2-R to the display
• Extracted Audio not working – This unit DOES NOT DOWNMIX, the source must be set to 2ch for the extracted 5 pin balanced audio port to work. For Toslink,  audio must be set to 5.1 or less to work.
• Still having issues, contact us
  • Support Direct – +1-605-977-3477
  • All inquiries – +1-605-274-6055
  • Submit a support request ticket
    https://support.avproedge.com/hc/en-us/request

Maintenance

To ensure reliable operation of this product as well as protecting the safety of any person using or handling this device while powered, please observe the following  instructions.

• Use the power supplies provided. If an alternate supply is required, check voltage, polarity and that it has sufficient power to supply the device it is connected to.
• Do not operate these products outside the specified temperature and humidity range given in the above specifications.
• Ensure there is adequate ventilation to allow this product to operate efficiently.
• Repair of the equipment should only be carried out by qualified professionals as these products contain sensitive components that may be damaged by any mistreatment.
• Only use this product in a dry environment. Do not allow any liquids or harmful chemicals to come into contact with these products.
• Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.

Damage Requiring Service
The unit should be serviced by qualified service personnel if:

• The DC power supply cord or AC adaptor has been damaged
• Objects or liquids have gotten into the unit
• The unit has been exposed to rain
• The unit does not operate normally or exhibits a marked change in performance
• The unit has been dropped or the housing damaged

Support
Should you experience any problems while using this product, first, refer to the Troubleshooting section of this manual before contacting Technical Support. When calling,  the following information should be provided:

• Product name and model number
• Product serial number
• Details of the issue and any conditions under which the issue is occurring

Warranty
If your product does not work properly because of a defect in materials or workmanship, AVProEdge (referred to as “the warrantor”) will, for the length of the period  indicated as below, (Parts/Labor (10) Years), which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new  or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor. During the “Labor” Limited  Warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must mail-in your product during the warranty period. This Limited Warranty is extended only to the original purchaser and only covers product purchased as new. A purchase receipt or other proof of original purchase  date is required for Limited Warranty service.

This warranty extends to products purchased directly from AVPro or an authorized dealer. AVPro is not liable to honor this warranty if the product has been used in any  application other than that for which it was intended, has been subjected to misuse, accidental damage, modification or improper installation procedures, unauthorized repairs or is outside of the warranty period. Please direct any questions or issues you may have to your local dealer before contacting AVPro.

Thank you for choosing AVProEdge!
Please contact us with any questions. We are happy to be of service!

AVProEdge
2222 E 52nd St N ~ Sioux Falls, SD 57104
1-877-886-5112 ~ 605-274-6055
support@avproedge.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>