MINN KOTA PowerDrive 55 Trolling Motor with Foot Pedal Instruction Manual

: June 12, 2024
: MINN KOTA

Table of Contents

PowerDrive 55 Trolling Motor with Foot Pedal
Product Information
Registration
Serial Number
Made for Android™
Safety Considerations

PowerDrive 55 Trolling Motor with Foot Pedal

Product Information

The PowerDrive is a bow-mount trolling motor designed for use on
boats. It is manufactured by Minn Kota and comes with various
features and accessories.

Registration

It is important to register your trolling motor on the Minn Kota
website at minnkotamotors.com/register. Please keep your receipt
for future reference.

Serial Number

Your PowerDrive trolling motor has an 11-character serial number
that helps identify the model and year of manufacture. This serial
number is required when contacting consumer service or registering
your product. A duplicate copy of the serial number label is
included for future reference.

Location of Serial Number: The serial number is
located inside the mount below the motor rests.

Made for Android™

The PowerDrive is compatible with Android™ devices. The Made for
Android™ badge indicates that the accessory has been designed to
connect specifically to Android™ products and meets performance
standards.

Safety Considerations

Please read the user manual thoroughly before using the
PowerDrive trolling motor. Follow all instructions and pay
attention to safety and cautionary notices. This motor should only
be used by individuals who have read and understood the user
instructions. Minors must use this motor under adult
supervision.

Product Usage Instructions

Follow the installation instructions provided in the user
manual for properly installing the PowerDrive trolling motor.
Ensure that all hinge and pivot points, as well as moving
parts, are clear of fingers when stowing or deploying the motor. In
case of unexpected operation, disconnect the power leads from the
battery.
Use only Johnson Outdoors approved accessories with the Minn
Kota motor. Non-approved accessories may cause damage, unexpected
motor operation, and injury. Always use the product and approved
accessories, including remotes, as directed to avoid accidental or
unexpected motor operation. Keep all factory-installed parts, such
as motor and accessory covers, enclosures, and guards, in
place.
Familiarize yourself with the different parts of your boat,
including the bow, port gunwale, starboard, keel port, inboard,
outboard, transom, stern, and hull.

POWERDRIVE
BOW-MOUNT TROLLING MOTOR
Installation Instructions

INTRODUCTION

THANK YOU
Thank you for choosing Minn Kota. We believe that you should spend more time fishing and less time positioning your boat. That’s why we build the smartest, toughest, most intuitive trolling motors on the water. Every aspect of a Minn Kota trolling motor is thought out and rethought until it’s good enough to bear our name. Countless hours of research and testing provide you the Minn Kota advantage that can truly take you “Anywhere. Anytime.” We don’t believe in shortcuts. We are Minn Kota. And we are never done helping you catch more fish.

REGISTRATION
Remember to keep your receipt and immediately register your trolling motor on our website at minnkotamotors.com/register.
SERIAL NUMBER
Your Minn Kota 11-character serial number is very important. It helps to determine the specific model and year of manufacture. When Contacting consumer service or registering your product you will need to know your products serial number. A duplicate copy of your serial number label has been included which can also be entered in the One-Boat Network App for future reference.

NOTICE: The serial number on your PowerDrive is located inside the mount below the motor rests.

EXAMPLE

MOTOR INFORMATION (For Consumer Reference Only)

Model Serial Number:

Controller Serial Number:

Purchase Date:

Store Where Purchased:

NOTICE: Do not return your Minn Kota motor to your retailer. Your retailer is not authorized to repair or replace this unit. You may obtain service by: calling Minn Kota at 800-227-6433; returning your motor to the Minn Kota Factory Service Center; sending or taking your motor to any Minn Kota authorized service center. A list of authorized service centers is available on our website, at minnkotamotors.com. Please include proof of purchase, serial number and purchase date for warranty service with any of the above options.

Made for iPhone® 11 and iPhone X
For updated iOS, Humminbird® and Minn Kota® compatibility, visit minnkotamotors.com

Made for
AndroidTM

Use of the Made for Apple badge means that an accessory has been designed to connect specifically to the Apple product(s) identified in the badge, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. iPhone is a trademark of Apple Inc., registered in the U.S. and other countries. The trademark “iPhone” is used in Japan with a license from Aiphone K.K.

AndroidTM is a trademark of Google LLC. The Android robot is reproduced or modified from work created and shared by Google and used according to terms described in the Creative Commons 3.0 Attribution License.

2 | minnkotamotors.com

SAFETY CONSIDERATIONS
Please thoroughly read the user manual. Follow all instructions and heed all safety and cautionary notices. Use of this motor is only permitted for persons that have read and understood these user instructions. Minors may use this motor only under adult supervision.
WARNING
You are responsible for the safe and prudent operation of your vessel. We have designed your Minn Kota product to be an accurate and reliable tool that will enhance boat operation and improve your ability to catch fish. This product does not relieve you from the responsibility for safe operation of your boat. You must avoid hazards to navigation and always maintain a permanent watch so you can respond to situations as they develop. You must always be prepared to regain manual control of your boat. Learn to operate your Minn Kota product in an area free from hazards and obstacles.
WARNING
Never run the motor out of the water, as this may result in injuries from the rotating propeller. The motor should be disconnected from the power source when it is not in use or is off the water. When connecting the power-supply cables of the motor to the battery, ensure that they are not kinked or subject to chafe and route them in such a way that persons cannot trip over them. Before using the motor make sure that the insulation of the power cables is not damaged. Disregarding these safety precautions may result in electric shorts of battery(s) and/or motor. Always disconnect motor from battery(s) before cleaning or checking the propeller. Avoid submerging the complete motor as water may enter the lower unit through control head and shaft. If the motor is used while water is present in the lower unit considerable damage to the motor can occur. This damage will not be covered by warranty.
WARNING
Take care that neither you nor other persons approach the turning propeller too closely, neither with body parts nor with objects. The motor is powerful and may endanger or injure you or others. While the motor is running watch out for persons swimming and for floating objects. Persons whose ability to run the motor or whose reactions are impaired by alcohol, drugs, medication, or other substances are not permitted to use this motor. This motor is not suitable for use in strong currents. The constant noise pressure level of the motor during use is less than 70dB(A). The overall vibration level does not exceed 2,5 m/sec2.
WARNING
When stowing or deploying the motor, keep fingers clear of all hinge and pivot points and all moving parts. In the event of unexpected operation, remove power leads from the battery.
WARNING
It is recommended to only use Johnson Outdoors approved accessories with your Minn Kota motor. Using non-approved accessories including to mount or control your motor may cause damage, unexpected motor operation and injury. Be sure to use the product and approved accessories, including remotes, safely and in the manner directed to avoid accidental or unexpected motor operation. Keep all factory installed parts in place including motor and accessory covers, enclosures and guards.

minnkotamotors.com | 3

KNOW YOUR BOAT
Bow

Port Gunwale

Starboard

Keel Port

Inboard Outboard

Starboard

Transom

Stern Bow
Hull 4 | minnkotamotors.com

Gunwale

INSTALLATION

INSTALLING THE POWERDRIVE
Your new PowerDrive comes with everything you’ll need to directly install it to the boat. This motor can be directly mounted to the boat or coupled with a Minn Kota quick release bracket for ease of mounting and removal. For installation with a quick release bracket, refer to the installation instructions provided with the bracket. For compatible quick release mounting brackets and to locate your nearest dealer, visit minnkotamotors.com. To install the motor directly to the boat, please follow the instructions provided in this manual. Please review the parts list, mounting considerations and tools needed for installation prior to getting started. For additional product support, please visit minnkotamotors.com.
INSTALLATION PARTS LIST

Item / Assembly

Part # Description

Qty.

A

Includes

2994864 BAG ASSEMBLY – (BOLT, NUT, WASHERS)

1

1 – 4

1

2263462 BOLT-MOUNTING-1/4X2 W/STG

6

16

2

2261713 WASHER-1/4

6

14 15 13

3

2263103 NUT NYLOK 1/4-20 MTG

6

4

2301720 WASHER-MOUNTING RUBBER

6

4

U

12

Includes

1378170 PROP KIT 2091170 PWR PRP

1

5 – 8

V

A

1

Includes

1378121 PROP IND 2061122 (PWR PROP)

1

5 – 8

5

2061122 PROP-POWER (3.25″) 2091170 PROP-WW2 (3 5/8″) REAMED SUB)

1 1

2 3

6

2151726 WASHER-5/16 SS

1

7

2053101 NUT-PROP NYLOC

1

8

2092600 PIN-DRIVE 1.06″ LG SS

1

Z Includes 9 2994859 BAG ASY-TERROVA/V2,RUB.BUMPERS

1

9

2325110 PAD, FOOT PEDAL PD

5

10

2994728 FOOT PEDAL ASSEMBLY, PD

1

11

MOTOR ASSEMBLY

1

12

2390802 t LANYARD W/CARABINR, IP RMT

1

13

2994175 t REMOTE ASM, MICRO REMOTE

1

14

2394110 t TAG, MICRO REMOTE

1

15

490384-4 t CABLE, ETHERNET (M12-M12) 30′

1

16

490380-1 t CABLE, ETHERNET PIGTAIL-700 HD

1

p

23949112 t QCK REF.GUIDE, iP MICRO RMT BT

1

p

2317126 INSTRC-INSTALL, POWERDRIVE FW

1

p

2297165 MANUAL-DISCLAIMER,DWNLOAD INFO

1

11 19 18

D Includes 17

2996300 TIE WRAP ASM, 60″

1

D

17

2206300 TIE WRAP, LOW PROFILE 4″

10

p

2294950 OBN & REMOTE PAIR INSTRUCT

1

18

2994960

BAG ASM, CABLE ADPT, 490518-1 490518-1 MKR-MDI-2

1

9

19

2994961

BAG ASM, CABLE ADPT, 490537-2 490537-2 MKR-MI-1

1

p

2207131 STANDARD QS SETUP GUIDE

1

p Not shown on Parts Diagram. This part is included in an assembly and cannot be ordered individually. t Only available with models factory installed with GPS. l Only available with models factory installed with Dual Spectrum CHIRP

Z

67

8

5 U V

minnkotamotors.com | 5

INSTALLING THE POWERDRIVE

MOUNTING CONSIDERATIONS
It is recommended that the motor be mounted as close to the centerline of the boat as possible. Make sure the area under the mounting location is clear to drill holes and install nuts and washers. Make sure the motor rest is positioned far enough beyond the edge of the boat. The motor must not encounter any obstructions as it is lowered into the water or raised into the boat when stowed and deployed. Consider a quick release or adapter bracket with the installation of your motor. To view a list of accessories, please visit minnkotamotors.com.

View accessories available for your trolling motor at minnkotamotors.com.

TOOLS AND RESOURCES REQUIRED
· #3 and #2 Phillips Screw Driver · Drill · 9/32″ Drill Bit

· 7/16″ Box End Wrench · A second person to help with
the installation

· Pliers or Vice Grip

INSTALLATION

INSTALLING THE POWERDRIVE

1

a. Make sure that the Power Cables from the battery

are disconnected, or that the breaker, if equipped,

is “off”.

WARNING

Make sure the motor is mounted on a level surface and is not connected to a power source.

Power Cables

NOTICE: The PowerDrive has no power switch. When the Power Cables are connected to a battery, the PowerDrive is “on”. When the Power Cables are disconnected from the battery, the PowerDrive is “off”. If the Power Cables are connected to a breaker, the PowerDrive is “on” when the breaker is “on” and “off” when the breaker is “off”.

6 | minnkotamotors.com

INSTALLING THE POWERDRIVE

2

b. Place the mount on an elevated, level surface such

2c

as a workbench or the tailgate of a pickup. The

Sideplate Screw

motor, as removed from the box, should be in the

stowed position.

c. Remove the four sideplate screws using a #3 or #2 Phillips screwdriver. Two of these screws will be located on each side of the mount.

NOTICE: This motor weighs approximately 30 lbs. We recommend having a second person help with the installation.

2b

Sideplate Screw

Deployed

Stowed

3

d. Remove the Right Sideplate.

3e

e. Swing the Left Sideplate out and away from the Base Extrusion.

3d

Base Extrusion Left Sideplate
minnkotamotors.com | 7

INSTALLING THE POWERDRIVE

4

f. Place the mount as close to the centerline or keel of

the boat as possible. The motor can be installed on

either the Port or Starboard side of the boat based

on personal preference. Check placement with the

motor in the stowed and deployed positions. Review

the mounting considerations at the beginning of

the installation.

5 ITEM(S) NEEDED #4 x 6
g. When the motor is in the deployed position, make sure that the Shaft is 1-1/2″ out past the Gunwale of the boat. The lower unit, when stowed and deployed must not encounter any obstructions.
h. Check to be sure that the mount is level. Use the Rubber Washers (Item #4) provided to create a level surface if necessary.

6

i. It is recommended to mark at least 6 of the 12 holes

in the Base Extrusion and to have a minimum of

two bolts on each side that are located the farthest

apart. Ideal installation would allow for 6 bolts to be

used, with a minimum of 4.

j. Drill through the deck of the boat using a 9/32″ Drill Bit on the marked locations.

8 | minnkotamotors.com

Deck of Boat Keel

Gunwale

1-1/2″ Minimum

Shaft

Drilling Locations

Base Extrusion

Bow

Drilling Locations

INSTALLING THE POWERDRIVE

7 ITEM(S) NEEDED

4 x 6

1 x 6

k. Put a 1/4-20 x 3-1/2″ (Item #1) Screw in each of the drilled locations. The Screw should pass through the Base Extrusion and the boat deck. If the Rubber Washers (Item #4) are used, they should sit between the Base Extrusion and boat deck. Make sure to secure the motor with screws on each side of the Base Extrusion.

Screw

8 ITEM(S) NEEDED #2 x 6 #3 x 6
l. Place a Flat Washer (Item #2) and then a Nylock Nut (Item #3) at the end of each screw as shown and secure. Make sure all hardware is secure.
NOTICE: To prevent seizing of the stainless steel hardware, do not use high speed installation tools. Wetting the screws or applying an anti-seize may help prevent seizing.

Rubber Washer

Screw

Rubber Washer

Boat Deck

Flat Washer Nylock Nut

Boat Deck

minnkotamotors.com | 9

INSTALLING THE POWERDRIVE

9

m. Replace the Right Sideplate.

9n

n. Swing the Left Sideplate back into its correct position on the Base Extrusion.

9m

Right Sideplate

10

o. Replace the four sideplate screws using a #3 or #2 Phillips screwdriver. Two of these screws will be located on each side of the mount.

Base Extrusion

Left Sideplate

Sideplate Screw

10 | minnkotamotors.com

INSTALLING THE FOOT PEDAL

Installing the Foot Pedal
1 ITEM(S) NEEDED #9 x 5

10 x 1

a. Take the Foot Pedal (Item #10) and turn it over. Put a Foot Pedal Pad (Item

9) in each of the pad locations.

NOTICE: The pads are recommended when using the Foot Pedal on non-carpeted surfaces.
b. Locate the 7 pin Foot Pedal Connector on the Foot Pedal and the Power Connector from the Motor. Align the pins of the Foot Pedal Connector to the matching socket end of the Power Connector. Firmly push the Plug together.
NOTICE: The connectors are keyed to prevent reversed installation.

Foot Pedal Connector

Foot Pedal Bottom
Foot Pedal Pad
Placement
Power Connector from Motor

Installing the Prop

1

CAUTION

Disconnect the motor from the battery before beginning any prop work or maintenance.

a. While holding the Shipping Spacer with a pliers or vise grip, remove the Prop Nut, Red Shipping Washer, Prop Washer and Spacer, being careful not to lose the Drive Pin. Reuse the Prop Nut, Prop Washer and Drive Pin to attach the Propeller.

NOTICE: The Shipping Spacer and Red Shipping Washer are for shipping purposes only and must be discarded. The Red Shipping Washer will rust if used to attach the Propeller.

Prop Washer
Prop Nut

Drive Pin

Shipping Spacer Red (discard) Shipping Washer (discard)

minnkotamotors.com | 11

INSTALLING THE PROP

2

ITEM(S) NEEDED

5 x 1 #6 x 1 #7 x 1 #8 x 1

b. Take the Drive Pin (Item #8) and slide it through the Hole in the Armature Shaft. Position the Drive Pin horizontal by grasping the Armature Shaft and rotating it with the Drive Pin in place.
c. Align the Propeller (Item #5) so it is also horizontal and parallel with the Drive Pin. Slide the Propeller onto the Armature Shaft and Drive Pin until it is seated against the lower unit.
d. Install the Prop Washer (Item #6) and the Prop Nut (Item #7) onto the end of the Armature Shaft.

2b Drive Pin
Prop Washer 2c

Armature Shaft

Propeller

Prop Nut

Propeller

3

e. Holding the end of the Armature Shaft with a Flat

Blade Screwdriver, tighten the Prop Nut with a 9/16″

Open End Wrench.

f. Tighten the Prop Nut 1/4 turn past snug to 25-35 in-lbs.
CAUTION

Do not over tighten as this can damage the prop.

Prop Washer

Drive Pin

Prop Nut Propeller

12 | minnkotamotors.com

IDENTIFYING TROLLING MOTOR FEATURES AND THEIR ASSOCIATED CABLES

Feature & Cable Identification

The PowerDrive may be pre-installed with Dual Spectrum CHIRP sonar or Advanced GPS Navigation – including the ability to connect via Ethernet to a Humminbird fish finder. These features may be installed on their own or in combination with another feature. All of these features require Accessory Cables to be connected to an output device. The connectors are present on the trolling motor and have cables that exit below the Control Head or exit the Coil Cord at the base of the Mount. To better identify Accessory Cables present, refer to the diagrams that detail what the Dual Spectrum CHIRP and Advanced GPS Navigation connectors look like.

Dual Spectrum CHIRP
Fourteen Pin Connector Locking Collar
Dual Spectrum CHIRP from Trolling Motor

Advanced GPS Navigation
Eight Pin Connector Threaded Collar
Ethernet Cable from Trolling Motor

Identifying Connectors
If there are NO connectors below the Control Head, the trolling motor may be equipped with:
Foot Pedal – The Power Connector to the Foot Pedal will be present at the base of the Mount along with the Power Leads. The Power Connector is keyed and attaches to the Eight Pin Connector from the Foot Pedal.

If ONE connector is present below the Control Head the trolling motor is equipped with:
Dual Spectrum CHIRP – If Dual Spectrum CHIRP is pre-installed on your trolling motor, one Dual Spectrum CHIRP accessory cable will exit the base of the Control Head and run down the center of the Coil Cord. The end of the cable will have a Fourteen Pin Connector. Motors with Dual Spectrum CHIRP will also have a transducer in the Lower Unit. Motors with Dual Spectrum CHIRP will have a Power Connector for the Foot Pedal present at the base of the Mount along with the Power Leads.

Dual Spectrum CHIRP Lower Unit

Dual Spectrum CHIRP Transducer

NO Connectors

Foot Pedal

Control Head Coil Cord

Power Leads

Foot Pedal Power
Connector

ONE Connector

Control Head
Dual Spectrum
CHIRP

Foot Pedal Power Connector

Fourteen Pin Connector

Dual Spectrum
CHIRP

Coil Cord

Lower Unit Side View
©2023 Johnson Outdoors Marine Electronics, Inc.

Lower Unit Bottom View

Mount

Foot Pedal Power
Connector

Power Leads

minnkotamotors.com | 13

IDENTIFYING TROLLING MOTOR FEATURES AND THEIR ASSOCIATED CABLES

If TWO connectors are present below the Control Head the trolling motor will be equipped with:
Advanced GPS Navigation – If Advanced GPS Navigation is pre-installed on your trolling motor, one eight pin Advanced GPS Ethernet Connector will exit the base of the Control Head and rest just below the Control Head next to the Coil Cord and one Advanced GPS Cable will exit the base of the Control Head and run down the center of the Coil Cord. The Advanced GPS Cable will come to a “Y” near the Mount of the trolling motor. One half of the “Y” will enter the Mount next to the Power Leads and the main portion of the cable will be attached from the factory to the Foot Pedal Power Connector. If a trolling motor is equipped with Advanced GPS Navigation, it will not be equipped with a Foot Pedal. If the Advanced GPS Navigation on the trolling motor will be used with a fish finder, an Ethernet Cable may be attached to the Advanced GPS Ethernet Connector below the Control Head. See the “Advanced GPS Navigation” section of this document for details on how to install the Advanced GPS Ethernet Connector to a Humminbird.
If THREE connectors are present below the Control Head the trolling motor will be equipped with:
Dual Spectrum CHIRP & Advanced GPS Navigation – If Dual Spectrum CHIRP is pre- installed on your trolling motor, one Dual Spectrum CHIRP accessory cable will exit the base of the Control Head and run down the center of the Coil Cord. The end of the Cable will have a Fourteen Pin Connector. Motors with Dual Spectrum CHIRP will also have a transducer in the Lower Unit.
If Advanced GPS Navigation is pre-installed on your trolling motor, one Advanced GPS Ethernet Connector will exit the base of the Control Head and rest just below the Control Head next to the Coil Cord and one Advanced GPS Cable will exit the base of the Control Head and run down the center of the Coil Cord. The Advanced GPS Cable will come to a “Y” near the Mount of the trolling motor. One half of the “Y” will enter the Mount next to the Power Leads and the main portion of the cable will be attached from the factory to the Foot Pedal Power Connector. Motors with Advanced GPS Navigation and Dual Spectrum CHIRP will not have a Foot Pedal. If the Advanced GPS Navigation on the trolling motor will be used with a fish finder, an Ethernet Cable may be attached to the Advanced GPS Ethernet Connector below the Control Head. See the “Advanced GPS Navigation” section of this document for details on how to install the Advanced GPS Ethernet Connector to a Humminbird.

TWO Connectors Control Head

Advanced GPS Cable

Advanced GPS
Ethernet Connector
Coil Cord

Eight Pin Connector

Advanced GPS Cable

Foot Pedal Power
Connector

Mount

Power Leads

THREE Connectors

Control Head

Advanced GPS
Ethernet Connector

Dual Spectrum
CHIRP

Advanced GPS Cable

Eight Pin Connector
Coil Cord

Fourteen Pin Connector
Dual Spectrum
CHIRP
Foot Pedal Power
Connector

Mount

Advanced GPS Cable

Power Leads

Dual Spectrum CHIRP Lower Unit

Dual Spectrum CHIRP Transducer

Lower Unit Side View

Lower Unit Bottom View

14 | minnkotamotors.com

DUAL SPECTRUM CHIRP

Feature & Cable Management

DUAL SPECTRUM CHIRP

Your trolling motor may be pre-installed with a transducer system featuring Humminbird’s Dual Spectrum CHIRP. CHIRP stands for “Compressed High Intensity Radar Pulse”. Dual Spectrum CHIRP is a 2D sonar transducer with a temperature sensor that is integrated into the lower unit of the trolling motor. Humminbird also utilizes a proprietary, best-in-class transducer designed and built to maximize fish detail, as well as coverage area. Dual Spectrum CHIRP scans the water for fish similar to the way the seek function on your truck’s radio scans the airwaves for FM stations. By covering a wide range of frequencies, CHIRP produces more accurate, more detailed returns of fish, structure, and the bottom.

Dual Spectrum CHIRP Lower Unit

Dual Spectrum CHIRP Transducer

Lower Unit Side View
Wide Mode

Lower Unit Bottom View
Narrow Mode

Humminbird’s Dual Spectrum CHIRP gives you full spectrum capability, plus the power to select your own start and end frequencies by operating in two different modes. Wide Mode for maximum coverage and Narrow Mode for maximum detail. Wide mode allows you to search deep and wide. Is it used for watching your lure while vertical jigging, or gaining a more expansive view in shallow water. Narrow Mode is used to hone in on the small stuff that makes a big difference. Narrow Mode provides a precise perspective of the water below, helping you target individual fish, or identify fish hidden in structure and/or tight to the bottom.

Dual Spectrum CHIRP features:

SUPERIOR TARGET SEPARATION – Separating fish from their habitat is the name of the game. And now, you’ll be able to tell the difference more easily between bait and game fish, and nearby structure and vegetation.

CLEARLY DEFINED FISH ARCHES – We’ve got bad news for your arch nemesis. Large game fish will show up on your screen as long, well-defined arches, for quick identification and accurate lure presentation.

STRONG RETURNS WITHOUT NOISE – Stop seeing things that aren’t there. A high signal-to-noise ratio translates to better defined targets, less clutter and greater certainty that what you’re looking at on-screen is legit.

Target Separation

Defined Fish Arches

Strong Returns

minnkotamotors.com | 15

DUAL SPECTRUM CHIRP

The integrated design of the Dual Spectrum CHIRP transducer protects it in the lower unit of the trolling motor from underwater hazards and prevents tangles and damage to the transducer cables. In certain situations, air bubbles may adhere to the surface of the Dual Spectrum CHIRP transducer and affect the performance. If this happens, simply wipe the surface of the transducer with your finger.
Considerations for Connecting and Routing Dual Spectrum CHIRP
If Dual Spectrum CHIRP is pre-installed on your trolling motor, one Dual Spectrum CHIRP accessory cable will exit the base of the Control Head and run down the center of the Coil Cord. Dual Spectrum CHIRP requires cables to be connected to an output device such as a Humminbird® fish finder. The Dual Spectrum CHIRP cable that exits the Coil Cord is “Apex and Solix Ready”. Connecting the trolling motor equipped with a Dual Spectrum CHIRP transducer to a compatible fish finder gives you a 2D sonar view of what is happening directly below your trolling motor. To determine if your fish finder is compatible with Dual Spectrum CHIRP, please visit minnkotamotors.com to check compatibility. The Dual Spectrum CHIRP cable from the trolling motor may be plugged directly into a Solix or Apex, directly into an Extension Cable or directly into a Humminbird® Helix Adapter Cable.
EXTENSION CABLES – The Dual Spectrum CHIRP cable from the trolling motor may not be long enough to reach your fish finder. If the cable length does not reach the desired fish finder installation location, extension cables are available. A 10-foot extension cable (EC M3 14W10 – 10″ transducer extension cable – 720106-1) and a 30-foot extension cable (EC M3 14W30 – 30″ transducer extension cable – 720106-2) are available from humminbird.com. Both the 10-foot and 30-foot extension cables also come “Apex and Solix Ready”. The Extension Cables may plug directly into a Solix or Apex or directly into a Helix Adapter Cable.
HUMMINBIRD HELIX ADAPTER CABLES – If connecting to a Humminbird® Helix fish finder, an adapter cable accessory is included that will allow the connection of any compatible Humminbird® Helix fish finder. The 490537-2 MKR-MI-1 is used on Helix 8, 9, 10, 12 and 15 G2N models and newer. The 490518-1 MKR-MDI-2 is used for Helix 7 G3, G4, G3N and G4N models. The Helix adapter cables will plug directly into the Helix fish finder.
OTHER FISH FINDER ADAPTER CABLES – If connecting to other fish finders on the market, check for compatibility or any required adapter cables online at minnkotamotors.com.

Dual Spectrum CHIRP Connections

Control Head
Dual Spectrum
CHIRP

Directly to Solix or Apex

Coil Cord

Dual Spectrum
CHIRP

Extension Cable
(if needed)

Helix Adapter Cable
(provided)
To Helix

Mount

Foot Pedal Power
Connector

Power Leads

16 | minnkotamotors.com

DUAL SPECTRUM CHIRP

All Dual Spectrum CHIRP PowerDrive motors are equipped with an internal bonding wire. Incorrect rigging will cause sonar interference and can damage your trolling motor, electronics, and other boat accessories. To minimize trolling motor interference, ensure that the fish finder and trolling motor are powered by separate batteries. Please refer to the “Battery & Wiring Installation” and “Motor Wiring Diagram” sections of this manual for correct rigging instructions.
The Dual Spectrum CHIRP cables are shielded to minimize interference. To protect this shielding, the cables should not be pulled tight against sharp angles or hard objects. If using cable ties, do not over-tighten. Any excess cable should be bundled in a loose loop of no less than 4″ in diameter. The connection cable should be routed to the fish finder following Minn Kota recommendations on routing the cables to optimize mobility and maximize functionality. Follow the instructions below for completing all connections and then follow the instructions for “Securing Accessory Cables” to complete the output cable installation.
CAUTION
Failure to follow the recommended wire routing for installed features, if equipped, may cause damage to the product and void your product warranty. Route cables away from pinch points or other areas that may cause them to bend in sharp angles. Routing the cables in any way other than directed may cause damage to the cables by being pinched or severed. Do not over-tighten the cable ties as it may damage the wires.

1 NOTICE: Your fish finder should be turned off until this procedure is complete.

Dual Spectrum CHIRP

a. Place the motor in the deployed position.
b. Locate the Fourteen Pin Connector on the end of the Dual Spectrum CHIRP accessory cable. The cable will exit the base of the Control Head and run down the center of the Coil Cord.
c. Determine if the Plug on the end of the Dual Spectrum CHIRP accessory cable will be attached directly to:

Coil Cord
Foot Pedal Mount Power
Connector

Power Leads

Fourteen Pin Connector

a Humminbird® Solix or Apex fish finder, 2) a Dual Spectrum CHIRP Extension Cable, 3) a Helix Adapter Cable or a compatible fish finder adapter cable.

minnkotamotors.com | 17

DUAL SPECTRUM CHIRP

2

d. If installing directly to a Solix or Apex, the

connection will be flat on the back of the fish

finder display.

e. Align the pins on the Accessory Cable with the receptacle on the fish finder. Notice the keyed connectors. Tighten the Collar from the accessory cable to secure the connection. Once directly installed to the Solix or Apex, the connection is complete.

Fourteen Pin Connector
Dual Spectrum CHIRP Accessory Cable from
Trolling Motor

Solix or Apex Fish Finder

3

f. If installing directly to a Dual Spectrum CHIRP

Extension Cable, align the pins on the accessory

Fourteen Pin Connector

cable with the receptacle on the extension cable.

Notice the keyed connectors. Tighten the Collar

from the accessory cable to secure the connection.

Collar

g. If the Dual Spectrum CHIRP extension cable will be

attached directly to a Humminbird® Solix or Apex,

the connection will look exactly like the installation

directly into a Humminbird Solix or Apex fish finder. NOTICE: A 10-foot extension cable (EC M314W10

Dual Spectrum CHIRP Accessory Cable from Trolling Motor

– 10′ transducer extension cable – 720106-1)

and a 30-foot extension cable (EC M3 14W30 –

30′ transducer extension cable – 720106-2) are

available from humminbird.com.

Receptacle
Dual Spectrum CHIRP Extension Cable

18 | minnkotamotors.com

DUAL SPECTRUM CHIRP

4 ITEM(S) NEEDED #18 or 19 x 1

h. If installing directly to a Helix Adapter Cable, align the pins on the accessory cable or extension cable with the receptacle on the Helix Adapter Cable (Item #18 or 19). Notice the keyed connectors. Tighten the Collar from the accessory cable or extension cable to secure the connection.

4h Fourteen Pin Connector
Collar

Receptacle

NOTICE: The 490537-2 MKR-MI-1 (Item #19) is a Helix Adapter Cable used on Helix 8, 9, 10, 12 and 15 G2N models and newer. The 490518-1 MKR-MDI-2 (Item

18) is a Helix Adapter Cable used for Helix 7 G3, G4, G3N and G4N models.

Both cables are included.
i. If the Helix Adapter Cable will be attached directly to a Humminbird® Helix, plug it in the Helix Adapter Cable Keyed Connection on the back of the fish finder.
NOTICE: If connecting to other fish finders on the market, check for compatibility or any required adapter cables online at minnkotamotors.com.

Dual Spectrum CHIRP Accessory Cable or Extension Cable
4i
Helix Adapter Cable

Helix Adapter Cable
Adapter Cable Keyed Connector Plug into Helix Fish Finder

j. If your trolling motor has more than one external connector for an output device, complete the connection for that specific output and then follow the instructions for “Securing Accessory Cables” to complete the output cable installation.

NOTICE: If unsure of what features your trolling motor may be installed with that require connection to an output device, please review the “Identifying Trolling Motor Features And Their Associated Cables” in this document.

minnkotamotors.com | 19

ADVANCED GPS NAVIGATION
ADVANCED GPS NAVIGATION
Your Minn Kota trolling motor and Humminbird fish finder communicate with each other to change the way you fish. Advanced GPS Navigation offers a large array of features including controlling speed, steering, Spot-Lock, and the ability to record and retrace tracks on the water, all at your fingertips. To learn more about the GPS capabilities available with your new motor, please refer to the Advanced GPS Navigation Owner’s Manual by visiting minnkotamotors.com. The wireless remote and GPS controller make up the Advanced GPS Navigation system. A wireless remote comes paired to the controller from the factory. The GPS controller contains a very sensitive compass and is where all GPS satellite and remote signals are received. The GPS controller is located in the trolling motor Control Head and may be connected to a fish finder from an Accessory Cable that exits the Control Head. If the Advanced GPS Navigation system will be used with a fish finder, the Ethernet link between the trolling motor and the fish finder must be connected.
Considerations for Connecting and Routing Advanced GPS Navigation
If Advanced GPS Navigation is pre-installed on your trolling motor, one eight pin Advanced GPS Ethernet Connector will exit the base of the Control Head and rest just below the Control Head next to the Coil Cord and one Advanced GPS Cable will exit the base of the Control Head and run down the center of the Coil Cord. The Advanced GPS Cable will come to a “Y” near the Mount of the trolling motor. One half of the “Y” will enter the Mount next to the Power Leads and the main portion of the cable will be attached from the factory to the Foot Pedal Power Connector. The Advanced GPS Cable that comes to a “Y” near the mount is pre-installed and should be left in place. If a trolling motor is equipped with Advanced GPS Navigation, it will not be equipped with a Foot Pedal. If the Advanced GPS Navigation on the trolling motor will be used with a fish finder, an Ethernet Cable will need to be attached to the Advanced GPS Ethernet Connector below the Control Head. Consider the distance between the trolling motor and the fish finder to determine how to complete the Ethernet connection. ETHERNET CABLES – Minn Kota provides one 30 ft Ethernet cable (AS EC 30E – 30′ Ethernet Cable – 720073-4) with every trolling motor equipped with Advanced GPS Navigation. The 30 ft Ethernet cable will accommodate a standard Ethernet connection for most installations to a Humminbird fish finder and is “Apex and Solix Ready”. If the distance between the trolling motor and Humminbird fish finder is relatively small and a shorter cable is preferred, alternate cable lengths are available from humminbird.com. These options include:
· 10 ft – (AS EC 10E – 10′ Ethernet Cable – 720073-2) · 15 ft – (AS EC 15E – 15′ Ethernet Cable – 720073-5) · 20 ft – (AS EC 20E – 20′ Ethernet Cable – 720073-3) Every length of Ethernet cable plugs directly into a Solix or Apex or directly into a Helix Adapter Cable. HUMMINBIRD HELIX ADAPTER CABLES – Minn Kota provides one Helix Adapter Cable (AS EC QDE – Ethernet Adapter Cable 720074-1) with every trolling motor equipped with Advanced GPS Navigation. If the Ethernet connection is being made between the trolling motor and any Humminbird® Helix fish finder, the Helix Adapter Cable should be used. The Helix Adapter Cable directly connects the Ethernet Cable to a Helix fish finder. ETHERNET EXTENSION CABLES – If the 30 ft Ethernet cable provided with your trolling motor with Advanced GPS Navigation is not long enough to reach the fish finder, an Ethernet Extension cable should be used. The Ethernet Extension cable is available from humminbird.com and is available in a 30 ft length (AS ECX 30E – 30′ Ethernet Extension Cable – 760025-1). The Ethernet Extension Cable will plug directly into any length of Ethernet cable.
NOTICE: Minn Kota recommends routing the Ethernet Cable or Ethernet Extension Cable through the Coil Cord when making the Ethernet connection. The cables will be installed from the Mount to the Control Head through the Coil Cord and parallel to the Advanced GPS Cable. Bypassing the Coil Cord when routing the Ethernet Cable or Ethernet Extension Cable is not recommended.

20 | minnkotamotors.com

ADVANCED GPS NAVIGATION

GPS Ethernet Connection
Control Head
Advanced GPS Ethernet Connector

Advanced GPS Cable
Coil Cord

Advanced GPS Cable

Ethernet Cable (provided)
Foot Pedal Power Connector

Helix Adapter Cable (if needed)

To Helix

Directly to Solix or Apex

Mount

Power Leads

CAUTION
Failure to follow the recommended wire routing for installed features, if equipped, may cause damage to the product and void your product warranty. Route cables away from pinch points or other areas that may cause them to bend in sharp angles. Routing the cables in any way other than directed may cause damage to the cables by being pinched or severed. Do not over-tighten cable ties as it may damage the wires.

1 NOTICE: Your fish finder should be turned off until this procedure is complete.
a. Place the motor in the deployed position.
b. Locate the Eight Pin Advanced GPS Ethernet Connector below the Control Head. The Advanced GPS Ethernet Connector will exit the base of the Control Head and will rest just below the Control Head next to the Coil Cord.

Control Head

Advanced GPS Ethernet
Connector

Advanced GPS Cable

Eight Pin Advanced GPS Ethernet Connector

Advanced GPS Cable

Foot Pedal Power
Connector

Mount

Power Leads minnkotamotors.com | 21

ADVANCED GPS NAVIGATION

2 ITEM(S) NEEDED

15 x 1

c. Take the Ethernet Cable (Item #15) and identify the Receptacle on either end. It will be keyed to fit with the Eight Pin Advanced GPS Ethernet Connector below the Control Head.
NOTICE: The Ethernet Cable has a Receptacle for the Advanced GPS Ethernet Connector on both ends and either end may be connected.
d. Leading with either Receptacle, take the cable and fish it through the center of the Coil Cord starting at the end of the Coil Cord attached to the Mount and working up towards the Control Head. The cable will run parallel to the Advanced GPS Cable. Allow enough slack in the cable to attach the Receptacle to the Advanced GPS Ethernet Connector.
NOTICE: The 30′ Ethernet Cable (AS EC 30E 30′ Ethernet Cable – 720073-4) is provided. If an alternate length is preferred, alternate cable lengths are available from humminbird.com.
NOTICE: The 30′ Ethernet Extension Cable (AS ECX 30E – 30′ Ethernet Extension Cable 760025-1) is available from humminbird.com and should be used if the standard 30′ Ethernet Cable provided with your trolling motor is not long enough to reach the fish finder.

2c Eight Pin
Connector

Receptacle

Advanced GPS Ethernet Connector from Trolling Motor
2d Control Head
Advanced GPS Ethernet Connector

Ethernet Cable

Advanced GPS Cable

Advanced GPS Ethernet
Connector
Ethernet Cable
Advanced GPS Cable

Mount

Foot Pedal Power Connector

Power Leads

22 | minnkotamotors.com

ADVANCED GPS NAVIGATION

3

NOTICE: Minn Kota recommends routing the

3e

Ethernet Cable through the Coil Cord when

making the Ethernet connection. The cable will be installed from the Mount to the Control Head through the Coil Cord and parallel to the Advanced GPS Cable. Bypassing the Coil Cord when routing the Ethernet Cable is not recommended.

Control Head
Advanced GPS
Ethernet Connector

e. To install the Ethernet Cable, align the pins on the Advanced GPS Ethernet Connector with the Receptacle on the Ethernet Cable. Notice the keyed connectors. Press the ends together and tighten the Collar from the Ethernet Cable to secure the connection.

Receptacle
Ethernet Cable

Ethernet Cable

f. The Ethernet Cable will plug directly into a Solix or Apex Fish Finder or directly into a Helix Adapter Cable.

Mount
3e Eight Pin Connector

Foot Pedal Power Connector

Power Leads

Receptacle

4

g. If installing directly to a Solix or Apex, the

connector will be flat on the back of the fish

finder display.

h. Align the Receptacle on the Ethernet Cable with the Eight Pin Connector on the Apex or Solix fish finder. Notice the keyed connectors. Tighten the Collar from the Ethernet Cable to secure the connection. Once directly installed to the Solix or Apex, the connection is complete.

Advanced GPS Ethernet Connector from Trolling Motor

Ethernet Cable

Receptacle
Ethernet Cable

Eight Pin Connector on Solix or Apex Fish Finder

minnkotamotors.com | 23

ADVANCED GPS NAVIGATION

5 ITEM(S) NEEDED

16 x 1

i. If installing directly to a Helix Adapter Cable (Item #16), align the Receptacle on the Ethernet Cable with the Eight Pin Connector on the Helix Adapter Cable provided. Notice the keyed connectors. Tighten the Collar from the Ethernet Cable to secure the connection.

5i
Ethernet Cable

Receptacle

Eight Pin Connector

Helix Adapter Cable

NOTICE: Minn Kota provides one Helix Adapter Cable (AS EC QDE – Ethernet Adapter Cable 720074-1) with every trolling motor equipped with Advanced GPS Navigation.
j. The Helix Adapter Cable directly connects the Ethernet Cable to a Helix fish finder. Locate the Helix Adapter Cable Keyed Connector on the back of the fish finder. Plug the Helix Adapter Cable into the back of the Helix fish finder to complete the connection.
k. If your trolling motor has more than one external connector for an output device, complete the connection for that specific output and then follow the instructions for “Securing Accessory Cables” to complete the output cable installation.

5j Ethernet Cable

Helix Adapter Cable

Adapter Cable Keyed Connector
Plug into Helix Fish
Finder

NOTICE: If unsure of what features your trolling motor may be installed with that require connection to an output device, please review the “Identifying Trolling Motor Features and Their Associated Cables” section of this manual.

24 | minnkotamotors.com

SECURING ACCESSORY CABLES

Securing Accessory Cables

Before securing the Accessory Cables, please review the “Identifying Trolling Motor Features and Their Associated Cables” section of this document. When identifying features, it is very important to secure

NOTICE: If only one cable is present below the Control Head, this installation is not applicable.

the cables if two or more connections are present below the Control

Head. If only one cable is present below the Control Head, this installation is not applicable. All Accessory Cables that will be used on the

trolling motor must be routed and all connections secured before completing the installation in this section. To review how Accessory Cables

should be routed and connected, please review the “Dual Spectrum CHIRP” and “Advanced GPS Navigation” sections of this document.

Mount

Foot Pedal Power Connector

Advanced GPS Cable (if equipped)

Advanced GPS Ethernet
Connector (if equipped)

Power Leads

Ethernet Cable or Ethernet Extension
Cable

Coil Cord
Dual Spectrum CHIRP (if equipped)

Control Head
Dual Spectrum
CHIRP (if equipped)

CAUTION
Failure to follow the recommended wire routing for installed features, if equipped, may cause damage to the product and void your product warranty. Route cables away from pinch points or other areas that may cause them to bend in sharp angles. Routing the cables in any way other than directed may cause damage to the cables by being pinched or severed. Do not over-tighten the cable ties as it may damage the wires.

1

a. Begin with the Trolling Motor in the stowed

position and have all Accessory Cables identified,

routed and connected.

b. If equipped with Advanced GPS Navigation, the Advanced GPS Ethernet Connector should be present just below the Control Head next to the Coil Cord. Locate the Advanced GPS Ethernet Connector below the Control Head.

Control Head
Advanced GPS Cable (if equipped)
Dual Spectrum CHIRP (if equipped)

Advanced GPS Ethernet
Connector (if equipped)
Ethernet Cable or Ethernet Extension
Cable

minnkotamotors.com | 25

SECURING ACCESSORY CABLES

2 ITEM(S) NEEDED #17 x 1

c. Check the Accessory Cables and confirm that the cables that are connected run parallel down the center of the Coil Cord.
d. While the motor is in the stowed position, straighten the Accessory Cables so they run neatly from the Control Head to the Mount.
e. Starting approximately 4 inches below the Control Head, take a Cable Tie (Item #17) and place it around the Connection Cables inside the Coil Cord.
NOTICE: Do NOT secure the Accessory Cable to the Coil Cord. ONLY secure the Accessory Cables with the Cable Ties to the other Accessory Cables.
f. Secure the Cable Tie around the Accessory Cables until it is fingertip tight. Do not overtighten the Cable Tie as it will cause damage to the Accessory Cables.

Control Head
Advanced GPS Cable (if equipped)

Approximately 4 inches

GPS Ethernet Connection (if equipped)
Ethernet Cable or Ethernet Extension
Cable
Cable Tie

Dual Spectrum CHIRP
(if equipped)

CAUTION
Do not over-tighten the Cable Ties as it may damage the wires.

3

g. Follow the Accessory Cables from the Control

Head to the Mount and place additional Cable Ties every 4 inches around the Accessory Cables after the first Cable Tie. The number of Cable Ties

Control Head

Shaft

Approximately 4 inches

needed will vary depending on the length of your

trolling motor Shaft.

NOTICE: If additional Cable Ties are needed, a Service Assembly (#2996300 TIE WRAP ASM, 60″) is available from the Parts Ordering Portal at minnkotamotors.com.

Mount

Approximately 4 inches
Approximately 4 inches

First Cable Tie Cable Tie
Cable Tie
Cable Tie

26 | minnkotamotors.com

SECURING ACCESSORY CABLES

4

h. Continue placing Cable Ties around the

Accessory Cables until the cables exit the Coil

Cord next to the Mount, when the Motor is in the

stowed position. The Cable Ties should be placed

approximately every 4 inches.

i. After the Accessory Cables exit the Coil Cord continue to secure the cables every 4 inches until there are two Cable Ties in place on the Accessory Cables after the Coil Cord.

NOTICE: Secure the Cable Ties fingertip tight. It is recommended to have them ONLY tight enough so that they do not slide around on the Accessory Cables and hold the cables together.

Approximately 4 inches
Approximately 4 inches
Approximately 4 inches
Approximately 4 inches

Coil Cord Cable Tie

Control Head

Cable Tie

Cable Tie
Cable Tie

Cable Tie

Mount

minnkotamotors.com | 27

BATTERY & WIRING INSTALLATION

BOAT RIGGING & PRODUCT INSTALLATION
For safety and compliance reasons, we recommend that you follow American Boat and Yacht Council (ABYC) standards when rigging your boat. Altering boat wiring should be completed by a qualified marine technician. The following specifications are for general guidelines only:
CAUTION
These guidelines apply to general rigging to support your Minn Kota motor. Powering multiple motors or additional electrical devices from the same power circuit may impact the recommended conductor gauge and circuit breaker size. If you are using wire longer than that provided with your unit, follow the conductor gauge and circuit breaker sizing table below. If your wire extension length is more than 25 feet, we recommend that you contact a qualified marine technician.

CAUTION

An over-current protection device (circuit breaker or fuse) must be used. Coast Guard requirements dictate that each ungrounded current-carrying conductor must be protected by a manually reset, trip-free circuit breaker or fuse. The type (voltage and current rating) of the fuse or circuit breaker must be sized accordingly to the trolling motor used. The table below gives recommended guidelines for circuit breaker sizing.

CONDUCTOR GAUGE AND CIRCUIT BREAKER SIZING TABLE
This conductor and circuit breaker sizing table is only valid for the following assumptions:

1. No more than 2 conductors are bundled together inside of a sheath or conduit outside of engine spaces. 2. Each conductor has 105° C temp rated insulation. 3. No more than 3% voltage drop allowed at full motor power based on published product power requirements.

Motor Thrust / Model
42 lb., 45 lb. 50 lb., 55 lb.
70 lb.

Max Amp Draw
42 50 42

Circuit Breaker Amps Minimum 50 Amp 12 VDC 50 Amp 12 VDC 50 Amp 24 VDC

5 feet 8 AWG 8 AWG 8 AWG

Wire Extension Length

10 feet

15 feet

20 feet

6 AWG

4 AWG

2 AWG

4 AWG

2 AWG

8 AWG

6 AWG

25 feet 2 AWG 1 AWG 4 AWG

NOTICE: Wire Extension Length refers to the distance from the batteries to the trolling motor leads. Consult website for available thrust options. Maximum Amp Draw values only occur intermittently during select conditions and should not be used as continuous amp load ratings.

Reference United States Code of Federal Regulations: 33 CFR 183 Boats and Associated Equipment ABYC E-11: AC and DC Electrical Systems on Boats
28 | minnkotamotors.com

SELECTING THE CORRECT BATTERIES

SELECTING THE CORRECT BATTERIES
The motor will operate with any lead acid, deep cycle marine 12 volt battery/batteries. For best results, use a deep cycle, marine battery with at least a 105 amp-hour rating. Maintain battery at full charge. Proper care will ensure having battery power when you need it, and will significantly improve the battery life. Failure to recharge lead-acid batteries (within 12-24 hours) is the leading cause of premature battery failure. Use a multi-stage charger to avoid overcharging. We offer a wide selection of chargers to fit your charging needs. If you are using a crank battery to start a gasoline outboard, we recommend that you use a separate deep cycle marine battery/batteries for your Minn Kota trolling motor. For more information on battery selection and rigging, please visit minnkotamotors.com. Minn Kota trolling motors can run on Lithium Ion batteries. However, they are specifically designed to run on traditional lead acid batteries (flooded, AGM or GEL). Lithium Ion batteries maintain higher voltages for longer periods of time than lead acid. Therefore, running a Minn Kota trolling motor at speeds higher than 85% for a prolonged period could cause permanent damage to the motor.
WARNING
Never connect the (+) and the () terminals of the same battery together. Take care that no metal object can fall onto the battery and short the terminals. This would immediately lead to a short and extreme fire danger.
CAUTION
Refer to “Conductor Gauge and Circuit Breaker Sizing Table” in the previous section to find the appropriate circuit breaker or fuse for your motor. For motors requiring a 60-amp breaker, the Minn Kota MKR-19 60-amp circuit breaker is recommended.
CAUTION
Please read the following information before connecting your motor to your batteries in order to avoid damaging your motor and/or voiding your warranty.
ADDITIONAL CONSIDERATIONS
Using DC or Alternator Chargers
Your Minn Kota trolling motor may be designed with an internal bonding wire to reduce sonar interference. Most alternator charging systems do not account for this bonding wire, and connect the negative posts of the trolling motor batteries to the negative posts of the crank/starting battery. These external connections can damage connected electronics and the electrical system of your trolling motor, voiding your warranty. Review your charger’s manual carefully or consult the manufacturer prior to use to ensure your charger is compatible.
Minn Kota recommends using Minn Kota brand chargers to recharge the batteries connected to your Minn Kota trolling motor, as they have been engineered to work with motors that include a bonding wire.
Additional Accessories Connected to Trolling Motor Batteries
Significant damage to your Minn Kota motor, your boat electronics, and your boat can occur if incorrect connections are made between your trolling motor batteries and other battery systems. Minn Kota recommends using an exclusive battery system for your trolling motor. Where possible, accessories should be connected to a separate battery system. Radios and sonar units should not be connected to any trolling motor battery systems as interference from the trolling motor is unavoidable. If connecting any additional accessories to any trolling motor battery system, or making connections between the trolling motor batteries and other battery systems on the boat, be sure to carefully observe the information below.

minnkotamotors.com | 29

CONNECTING THE BATTERIES
The negative (-) connection must be connected to the negative terminal of the same battery that the trolling motor negative lead connects to. In the diagrams below this battery is labeled “Low Side” Battery. Connecting to any other trolling motor battery will input positive voltage into the “ground” of that accessory, which can cause excess corrosion. Any damage caused by incorrect connections between battery systems will not be covered under warranty.
Automatic Jump Start Systems and Selector Switches
Automatic jump start systems and selector switches tie the negatives of the connected batteries together. Connecting these systems to the “High Side” Battery or “Middle” Battery in the diagrams below and will cause significant damage to your trolling motor and electronics. The only trolling motor battery that is safe to connect to one of these systems is the “Low Side” Battery.
NOTICE: The internal bonding wire is equipped with a 3 amp fuse. Improper connections described above carrying in excess of 3 amps will blow this fuse and no further damage will be exhibited. If this occurs, RF interference from the trolling motor affecting sonar units and other electronics will be more significant. If the fuse is blown the wiring error should be found and addressed prior to replacing the fuse. The replacement fuse should be 3 amps or less. An intact fuse does not imply correct rigging; significant damage can be done by incorrect wiring without approaching 3 amps of current.
CONNECTING THE BATTERIES
12 Volt Systems
1. Make sure that the motor is switched off (speed selector on “OFF” or “0”). 2. Connect positive ( + ) red lead to positive ( + ) battery terminal. 3. Connect negative ( ) black lead to negative ( ) battery terminal.
WARNING
For safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and follow instructions in your boat owner’s manual.
WARNING
· For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries are being charged.
· Improper wiring of 24/36 volt systems could cause battery explosion. · Keep leadwire wing nut connections tight and solid to battery terminals. · Locate battery in a ventilated compartment.

30 | minnkotamotors.com

CONNECTING THE BATTERIES IN SERIES

CONNECTING THE BATTERIES IN SERIES (IF REQUIRED FOR YOUR MOTOR)
24 Volt Systems
Two 12 volt batteries are required. The batteries must be wired in series, only as directed in wiring diagram, to provide 24 volts.
1. Make sure that the motor is switched off (speed selector on “0”).
2. Connect a connector cable to the positive ( + ) terminal of battery 1 and to the negative ( ) terminal of battery 2.
3. Connect positive ( + ) red motor lead to positive ( + ) terminal on battery 2.
4. Connect negative ( ) black motor lead to negative ( ) terminal of battery 1.

To trolling motor negative

+24 Volts to trolling motor positive (or circuit breaker)

24 Volt Series Connection

Neg – Pos +

Battery #1 (Low Side)

Battery #2 (High Side)

Two 12-volt batteries connected in series for 24 volts

WARNING
For safety reasons do not switch the motor on until the propeller is in the water. If installing a leadwire plug, observe proper polarity and follow instructions in your boat owner’s manual.

WARNING
· For safety reasons, disconnect the motor from the battery or batteries when the motor is not in use or while the battery/batteries are being charged.
· Improper wiring of 24/36 volt systems could cause battery explosion. · Keep leadwire wing nut connections tight and solid to battery terminals. · Locate battery in a ventilated compartment.

minnkotamotors.com | 31

RECOMMENDED ACCESSORIES
ON-BOARD & PORTABLE BATTERY CHARGERS
Stop buying new batteries and start taking care of the ones you’ve got. Many chargers can actually damage your battery over time creating shorter run times and shorter overall life. Digitally controlled Minn Kota chargers are designed to provide the fastest charge that protect and extend battery life.

MK212PCL

MK210D

MK110PD

TALON SHALLOW WATER ANCHOR
Talon is the only shallow water anchor with up to 15′ of anchoring depth, multiple anchoring modes, and control from the bow, transom, console, remote or mobile device.

BUILT-IN WORK LIGHT
Lets you tie lines and work from the transom any time of day — or night. Includes both white and blue LED lights with three brightness settings.
BLUETOOTH® CONNECTIVITY
Lets you control Talon from your mobile device and easily update it. Also opens up communication to other control options.

UP TO 15′ DEEP
Control more water and catch more fish with the first 15′ shallow water anchor.
MORE CONTROL OPTIONS
· Control Panel · Wireless Remote · Mobile App · Wireless Foot Switch · Humminbird® Connectivity · Advanced GPS Navigation
System Remote

MINN KOTA ACCESSORIES

We offer a wide variety of trolling motor accessories, including:

· 60-Amp Circuit Breaker · Mounting Brackets · Stabilizer Kits · Extension Handles

· Battery Connectors · Battery Boxes · Quick Connect Plugs

minnkotamotors.com
Part #2317126

Minn Kota Consumer & Technical Service Johnson Outdoors Marine Electronics, Inc. PO Box 8129 Mankato, MN 56001
ECN 43378

121 Power Drive Mankato, MN 56001 Phone 800-227-6433 Fax 800-527-4464

Rev C

03/23