laia TPQ 22+ t-Pod Quad 22 Digital Audio System User Manual
- June 9, 2024
- laia
Table of Contents
LAIA t-Pod Quad 22Plus
P/N: TPQ 22+
User manual
Product overview
Pack
Product features
The high-quality wireless digital conference system equipment is based on the Internet computer equipment USB interface connection. The digital active loudspeaker plays the conference audio in real time and is equipped with a number of wireless pickup omnidirectional microphones with wider pickup coverage. At the same time, it is also equipped with local externa! microphone input interface so the meeting layout is more simple, fast and efficient.
Instructions
Determine the installation locations of the speaker and wireless microphones,
install the antenna on the speaker, connect it to the computer with the USB
cable, turn the volume knob to the minimum position, connect the device to the
power supply using its adapter and turn on the power switch of the speaker. At
all times, the indicator will be on green and the device will be in a standby
state.
Press and hold the on/off key of each wireless microphone in turn. When the
green light is on, it means the devices have successfully connected wirelessly
to the speaker.
Communication between remote and local locations will be established over the
network instantly. During the call process, it is necessary to moderately
increase the volume of the speaker to adjust the sensitivity of the microphone
and clearly hear the voice of local and remote meeting places. During the
call, you can press the “Mute Microphone” button to mute the wireless
connection. Press the “Mic Mute” button again to turn off the mute function
and the red ring light will turn on again.
During the call, you can press the “Mute Speaker” button to mute the wireless
connection. Press the “Speaker Mute” button again to turn off the mute
function and the red ring light will turn on again.
When the device is used in local and conference rooms, you can connect an
external microphone via the 6.5mm jack.
Note: This device is applicable for PC with Windows and other operating
systems. USB interface adopts USB1.1, USB2.0 or above; USB cable is plug and
play and does not need to install additional driver.
Installation and connection
As shown in the diagram of loudspeaker master, first install the externa!
antenna, connect the computer equipment with USB cables, then connect the
power input port of the loudspeaker master to the AC power socket with the
master power adapter, turn on the power switch of the master; then the master
indicator will be on in green.
Befare use, the wireless microphone slave should be connected with the USB
power adapter to fully charge the built-in ballery. The slave charging
indicator will be on in orange when charging and will be off when the battery
is fully charged. When the master is connected wirelessly, the slave ring
light flashes in red, indicating low ballery and that the ballery needs to be
charged in time.
Wireless microphone slave, Press and hold the bullan for a moment until the
ring green light is always on, indicating successful wireless connection with
the master. lf the green light flashes, indicating no wireless connection with
the master.
The installation distance between the loudspeaker master and all wireless
microphone slaves shall be more than 2m, and the recommended installation
distance between wireless microphone slaves shall be 1.5m.
Equipment introduction
1. Slave status ring light
2. Built-in microphone
3. Horn mute key
4. Volume – key
5. Volume + key
6. Microphone mute key
7. Charging indicator
8. USB charging interface
9. Slave on/off button| 10. Power switch
11. DC power input port
12. Volume adjusting knob
13. External antenna interface
14. External microphone gain adjustment
15. USB 5V power output port
16. 6.5mm microphone input port
17. Master indicator 18. Master USB data interface
19. Master horn
---|---
Notes
In addition to this device, the PC connected to the network must not be
connected with another microphone and speaker at the same time to avoid usage
problems.
Connect the USB cable of the speaker correctly to the computer. Improper use
of USB for connection will cause malfunction.
After the device connects successfully, the default mode for playback (output)
and recording (input) will be in “Local Device Model” in the sound and audio
device properties, from panel option computer control. Otherwise, you need to
select again “Local device model” to confirm.
Keep the built-in battery of the equipment away from high temperatures and
fire/heat sources to avoid the risk of explosion.
Please do not try to repair the equipment, otherwise it may cause electric
shock or short circuit. If there is a problem and the equipment needs to be
repaired, please contact your dealer.
Copyright © 2022 Laia
· www.laiatech.com
All rights reserved
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>