infobit D401 4×1 3G SDI Multiviewer with Seamless Switching User Manual

: June 12, 2024
: infobit

Table of Contents

Introduction
Key Features
Connections
Diagram
Spec
Install Software
Setup PC network
Control the iTrans D401
Quad-image modes
Setup resolution
Package list
Technical support
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

infobit D401 4×1 3G SDI Multiviewer with Seamless Switching

infobit D401 4x1 3G SDI Multiviewer with Seamless
Switching

Introduction

The iTrans D401 is a professional 4×1 SDI multiviewer that supports multiple 3G SDI signals. It supports 15x displaying mode including single image, dual images, quad images modes. With network control by the Windows- based software, the displaying modes can be switched. It supports seamless switching without any black screen intervals.

Key Features

4x 3G SDI inputs
2x 3G SDI mirror outputs
1x HDMI output
Single image, Dual-image PIP, Dual-image POP, Quad-image split view
Auto-cycle of single-images modes
Adaptive input signal, optional output resolutions
Seamless switching without any black screen intervals
DIP switch to setup output resolutions
With network control software
Supports SD/ HD/ 3G SDI
3G SDI Level A
With both DV and USB C power supply

Connections

No.

| Feature| Function
---|---|---
1| SDI IN|

4-CH SDI Inputs

2

| SDI OUT| 2-CH SDI Outputs, mirror
3| DC 12V|

12V DC power supply

4

| TYPE C| TYPE C for upgrade and power supply
5| SET|

DIP switch to adjust the output resolutions

6

|

RJ45

| Network port, connect to PC for control
7| HDMI OUT|

HDMI Output

8

| Audio Out/IN|

No function, reserved.

Diagram

Spec

Input

| Ports| 4-CH 3G-SDI signal inputs
---|---|---
Signal standard|

SD/HD/3G-SDI: SMPTE 259/274/292/296/372/424/425

Output

| Ports| 2-CH 3G-SDI signal outputs 1-CH HDMI output

Signal standard

| SD/HD/3G-SDI: SMPTE- 259/274/292/296/372/424/425

HDMI: HDTV standard HDMI signal

Size|

WDH

|

10912625 mm

Weight

| 1.5Kg
Power supply|

DC 12V

Operating temperature

| 0℃~50℃ non-condensation
Storage temperature|

-20℃~75℃

Install Software

Download the control software on our website: www.infobitav.com/itrans-d401
Install the control software iTrans D401_v1.0.1.6 (version should be updated without prior notice) on your Windows PC.

Setup PC network

The control PC must be setup with the IP address (192.168.1.xxx) to make sure it is within the same subnet with the iTrans D401 (default IP 192.168.1.215) at the first time connection.
Setup PC network
Then click the Scan button to search and select the detected device in the dropdown list.

After the iTrans D401 being connected, the user can change the device IP address as shown on below picture:

Setup PC network

Control the iTrans D401

3- (1) Scan and connect the iTrans D401

3- (2) Showing the Multiview mode with input signal number on each image.

3- (3) Status: Green means signal is available; Red means signal lost or disconnected.

Control the iTrans D401
3- (4) Mode switch: Click the right displaying mode to switch among the 15x built-in layouts.

3- (5) Auto cycle: enter the auto-cycling intervals (in seconds) and click Start button. The display will auto cycle among the 4x single images modes (Single image 1, 2, 3 and 4).

_ **3- (6) PIP: Select and switch the signal source for PIP or POP mode. Please note the first image only can be selected under POP mode and cannot be selected under PIP mode (the INPUT #1 is displaying on the background image by default under PIP mode).

3-(6)-1: PIP mode**_

3-(6)-2: POP mode