PROLED L710Px36x Downlight Piccolo Instruction Manual
- June 12, 2024
- PROLED
Table of Contents
PROLED L710Px36x Downlight Piccolo
Product Information
The PROLED DOWNLIGHT PICCOLO 35/45 – L710Px36x is a high-quality LED downlight designed for indoor use. It features the following characteristics:
- Energy efficiency: class F
- Input voltage: 220-240VAC
- Manufacturer: MBN GmbH
- Address: Balthasar-Schaller-Str. 3, 86316 Friedberg, Germany
- Website: www.proled.com
- Protection class: IP20
Warning
Before using the luminaire, please take note of the following warnings:
- For indoor use only
- Dispose of the packaging in a safe environment
- Do not use the luminaire if the cable is defected
- It is recommended to hire a qualified electrician for installation
- Avoid looking directly at the lighted luminaire
Ensure that the product is installed following European safety directives to avoid any liability from the manufacturer in case of damage caused by improper use or installation. Do not cover lamps with heat-insulating materials.
Safety Indices
A qualified electrician should complete the installation to ensure safety. The
manufacturer cannot be held liable for lights installed without observing
European safety directives. If any modification is made to the luminaire, the
person responsible for the modification will be considered as the
manufacturer.
Product Usage Instructions
Please follow the step-by-step installation instructions to ensure proper usage:
- Switch off the electricity at the mains before starting the installation or changing the lamp. If a fuse box is installed, remove the appropriate circuit fuse to prevent accidental switching on of the mains supply.
- Connect the luminaire to a constant current driver of either 500 mA or 350 mA on the secondary side.
- Connect the primary side of the driver to the power supply (230V).
- Ensure all connections are tight and secure, with no loose strands.
- Make sure the installation complies with fire regulations.
- If you have any doubts or questions about these instructions, consult a qualified electrician.
Follow the sequence below to avoid damaging the LED:
- First, connect the LED driver (not included).
- Second, connect the LED driver (not included) to the input voltage of 220-240VAC.
To install the luminaire in the ceiling:
- Create the necessary cutout for the luminaire and ensure there is enough installation space.
- Shut off the fuse in the fuse box.
- Connect the power supply to the primary side of the driver.
- Connect the secondary side of the driver to the luminaire.
- Install the luminaire in the ceiling according to the provided picture.
- Switch on the power supply.
PROLED DOWNLIGHT PICCOLO 35/45 – L710Px36x
Characteristics:
- COB Chip in Super Warm White
- LED power 1,5 Watt (PICCOLO 35, 500 mA) or 6 W (PICCOLO 45, 350 mA)
- Metal housing round in White or Black
- Beam angle 30°
- Driver 500 mA or 350 mA constant current (driver not included)
- Dimmable with special 500 mA or 350 mA constant current dimmer or 500 mA or 350 mA constant current driver
- Operating temperature range -10° C till +45° C
- CE compliant with applicable European directives
Warning:
- For indoor use only
- Please ensure that the packaging is disposed of in a safe environment
- If cable is defected, do not use the luminaire
- We do recommend that a qualified electrician should be used to install the products
- Do not look at the lighted luminaire directly
Safety indices
Be sure to have a qualified electrician complete installation. The customer is not entitled to claim for any lights installed without observing European safety directives. The manufacturer is then discharged from liability when damage is caused by improper use or installation. If any luminaire is subsequently modified, the person responsible for the modification shall be considered as manufacturer. Do not cover lamps with heat-insulating materials. For indoor use only. Protection class IP20.
Installation
Please follow the sequence of installation step by step. Non-observance can lead to damage of LED.
- Switch off the electricity at the mains before commencing installation or lamp change and (if a fuse box is installed) remove the appropriate circuit fuse to avoid accidental switching on of the mains supply.
- Connect to a constant current driver 500 mA or 350 mA (secondary side)
- Connect primary side of driver to power supply (230V)
- Make sure all connections are tight with no loose strands
- Ensure fire regulations are not breached when fitting your lights
- If you are in any doubt regarding these instructions, consult a qualified electrician
Please follow the sequence, if not destroying of LED possible:
REMARK TO ENERGY EFFICIENCY CLASS
This product contains a light source of energy efficiency class F.
ATTENTION:
- This product counts as „containing product“ according to directive (EU) 2019/2020 and (EU) 2019/2015.
- The light source is part of the containing product. A separation of the light source and the containing product using commonly available tools is possible with this product.
- Replacement of the light source using commonly available tools is possible with this product.
- The light source can be separated for testing purposes.
- Installation and commissioning may only be performed by qualifies persons.
- National installation regulations must be observed.
- Luminaires must be disconnected from mains before any work.
Installation steps
-
Please make the needed cutout for the luminaire and check (Point 6.), if needed installation space is existing.
-
Shut off fuse in fuse box. Connect the power supply to the primary side of the driver.
-
Connect secondary side of the driver with the luminaire.
-
Install the luminaire in the ceiling as shown on below picture and shut on the power supply.
-
Please pay attention that the luminaire isn’t covered by insulation material.
-
Please check needed installation space.
05.23 Technical amendments reserved
MBN GmbH, Balthasar-Schaller-Str. 3, 86316 Friedberg – Germany
www.proled.com