Happy Plugs Air 1 Plus User Manual
- June 12, 2024
- HAPPY PLUGS
Table of Contents
Happy Plugs Air 1 Plus
USER MANUAL
WHATS IN THE BOX
- 2 x AIR 1 PLUS Headphones
- Charge & Storage Case
- 2 x Silicone Sleeves
- USB-C Charging Cable
- Manual & Warranty Information
Quick Start
This is a guide for Air 1 Plus how to get started with Air 1 Plus Earbud & In- Ear. Are you looking for Air 1, Air 1 Go or Air 1 ANC ?
1. Charge
Before pairing Air 1 Plus to your bluetooth enabled device, make sure the Air 1 Plus charging case has been charged for a couple of minutes.
2. Pair the Earbuds
Take the earbuds out of the case and hold them close to each other. The LED- lights will blink rapidly. When paired, one of the LED:s will stop blinking, while the other continues.
Air 1 Plus is now ready to be connected to your bluetooth device.
3. Activate Bluetooth
Go into your device settings and enable Bluetooth. You should find Air 1 Plus in the list of devices.
When connecting, a pop-up prompt will ask you to connect. Press Accept/Allow.
Pro tip: If your device cannot find your Air 1 Plus headphones, try repeating the steps above. If still not working, you might need to perform a factory reset. Please refer to this guide on how to reset.
Pro tip: When inserting the earbuds into your ears, make sure not to press the touch controls. If you accidentally press the touch controls for four (4) seconds, your earbuds will turn off.
How To Use
CONNECT AND USE
1. Charge Air 1 Plus for a least 15 minutes before use.
2. Remove the earbuds from the charge case. Keep them within 10 cm / 4 inches
apart from each other until the LED on one of the earbuds stops blinking.
3. Select “Air 1 Plus” on your phone/device to pair. Wait for the pop-up
prompt and accept to do a full pair.
**When inserting the earbuds into your ears – make sure not to touch the touch control surface. A five second touch turns the earbud off.
RESET TO FACTORY SETTINGS
1. Delete “Air 1 Plus” from your Bluetooth devices list.
2. Make sure the charge case is charged. Put the earbuds in the charge case.
3. Touch and hold the touch sensors on both earbuds for 10 seconds until the
earphone LEDs blink 3 times.
The earbuds are now reset and ready to pair to your device.
Just follow the quickstart steps.
CALLS
When using the Air 1 Plus for phone calls, both earbuds are active.
**On Apple devices, while your Air 1 Plus is paired; go into Settings > Accessibility > Touch, scroll down to Call Audio Routing and select Bluetooth Headset.
SIRI OR GOOGLE ASSISTANT
Control calls and music with Siri or Google Assistant. On iPhone, go into Settings > Touch ID & Passcode, scroll down to Allow Access when locked and enable Siri.
TOUCH CONTROLS
J+R:
2 s Power On
5 s Power Off
10 s Reset (In the case)
L:
× 1 Volume Up
× 2 Volume Down
R:
× 2 Next Track
× 3 Previous Track
× 1 Call Answer / Call End
× 2 Reject Call
2 s Switch Call
2 s Siri / Google Assistant
How to Reset
1. Prepare
If you have connected Air 1 Plus to your phone or tablet before, go ahead and delete them now from the Bluetooth Settings. Also make sure the Air 1 Plus charging case has been charged for a couple of minutes.
2. Perform Factory Reset
Place the earbuds in the charging case. Press and hold both touch control areas for ten (10) seconds. Both LED-lights will flash three (3) times.
Air 1 Plus is now reset.
3. Pair the Earbuds
Take the earbuds out of the case and hold them close to each other. The LED- lights will blink rapidly. When paired, one of the LEDs will stop blinking, while the other continues.
Air 1 Plus is now ready to be connected to your bluetooth device.
Touch Commands
Note: This guide is valid for both Air 1 Plus Earbud and Air 1 Plus In-Ear
Locate the Touch Sensors
Air 1 Plus features touch just above LED lights on your earbuds. Press this area gently with you fingers to control music, calls and more. For the full overview of touch commands, see the list below:
Both Earbuds
2s Power On
5s Power Off
10s Reset (In the case)
Left Earbud
×1 Volume Up
×2 Volume Down
Right Earbud
×1 Play / Pause
×2 Next Track
×3 Previous Track
×1 Call Answer / Call End
×2 Reject Call
2s Switch Call
2s Siri / Google Assistant
Pro tip: When inserting the earbuds into your ears, try not press against the touch area, as this can turn off the earbud.
Multiple Devices
You can pair the Happy Plugs Air 1 products with up to eight different Bluetooth devices. The earphones stores and remembers these pairings. However, you can only be connected to one device at a time, e.g. play music from one Bluetooth device.
To change from one Bluetooth device to another, disconnect the current Bluetooth connection by switching off Bluetooth at the current device and connect to your second Bluetooth device by selecting the Happy Plugs Air 1 product entry in the Bluetooth menu.
When you remove your Happy Plugs Air 1 product from the charge case it will automatically connect to the last device you were connected to.
Supported Devices
Note: This guide is valid for both Air 1 Plus Earbud and Air 1 Plus In-Ear
Identify your Product
Air 1 Plus True Wireless Headphones are compatible with any device equipped with Bluetooth – that includes Apple products, as well as Android based devices.
Air 1 Plus supports Bluetooth 5.0 connection and below.
Don’t forget to activate Bluetooth on your device.
Technical Specifications
Note: This information is valid for both Air 1 Plus Earbud and Air 1 Plus In-Ear
CONNECTIVITY
Bluetooth Version 5.0
Operation Range: Up to 30m / 100 feet
AUDIO
Supported Bluetooth Profiles: HSP, HFP, A2DP & AVRCP
Supported Codecs: SBC, Qualcomm® aptX™
Driver: 12 mm
Sensitivity: 120dB ± 3dB
Impedance: 16 ohm
Frequency Response: 20-20k Hz
BATTERY
40 mAh battery in each earbud
630 mAh battery in the charging box
6 hours play and talk time in a single charge and 40 hours in total
Standby Time: up to 120 H
DOWNLOAD
Happy Plugs Air 1 Plus User Manual – [Download PDF]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>