Happy Plugs Air 1 Go User Manual

: June 12, 2024
: HAPPY PLUGS

Happy Plugs Air 1 Go

USER MANUAL

WHATS IN THE BOX

2 x AIR 1 GO Headphones
Charge & Storage Case
2 x Silicone Sleeves
Micro-USB Cable
Manual & Warranty Information

Quick Start

This guide helps you get started with Air 1 GO.

Quick Start

1. Charge

Before pairing Air 1 Go to your Bluetooth enabled device, make sure the Air 1 Go charging case has been charged for a couple of minutes.

2. Pair the Earbuds

Take the earbuds out of the case and hold them close to each other. The LED- lights will blink rapidly. When paired, one of the LEDs will stop blinking, while the other continues.

**Air 1 Go is now ready to be connected to your Bluetooth device.

3. Activate Bluetooth

Go into your device settings and enable Bluetooth. You should find Air 1 Go in the list of devices.

Pro tip: When inserting the earbuds into your ears, make sure not to press the touch controls. If you accidentally press the touch controls for four (4) seconds, your earbuds will turn off.

How To Starts Using

Menu

CONNECT AND USE

1. Charge Air 1 Go for a least 15 minutes before use.
2. Remove the earbuds from the charge case. Keep them within 10 cm / 4 inches apart from each other until the LED on the left earbud stops blinking.
3. Select “Air 1 Go” on your phone/device to pair.

When inserting the earbuds into your ears – make sure not to touch the touch control surface. A five second touch turns the earbud off.

RESET TO FACTORY SETTINGS

Delete “Air 1 Go” from your Bluetooth devices list.
Make sure the charge case is charged. Put the earbuds in the charge case.
Touch and hold the touch sensors on both earbuds for 10 seconds until the earphone LEDs blink 3 times.
The earbuds are now reset and ready to pair to your device.
Just follow the quickstart steps.

CALLS

When using the Air 1 Go for phone calls, both earbuds are active, but only the right (R) earbud has a microphone for speaking.

On Apple devices, while your Air 1 Go is paired; go into Settings > Accessibility > Touch, scroll down to Call Audio Routing and select Bluetooth Headset.

SIRI OR GOOGLE ASSISTANT

Control calls and music with Siri or Google Assistant.
On iPhone, go into Settings > Touch ID & Passcode, scroll down to Allow Access when locked and enable Siri.

TOUCH CONTROLS

L+R:

2 s Power On
5 s Power Off
10 s Reset (In the case)

L:

× 1 Volume Up
× 2 Volume Down

R:

× 1 Play / Pause
× 2 Next Track
× 3 Previous Track
× 1 Call Answer / Call End
× 2 Reject Call
2 s Switch Call
2 s Siri / Google Assistant

How to Reset

1. Prepare

If you have connected Air 1 Go to your phone or tablet before, go ahead and delete them now from the Bluetooth Settings. Also make sure the Air 1 Go charging case has been charged for a couple of minutes.

2. Perform Factory Reset

Place earbuds in the charging case. Press and hold both touch control areas for ten (10) seconds. Both LED-lights will flash three (3) times.

Air 1 Go is now reset.

3. Pair the Earbuds

Take the earbuds out of the case and hold them close to each other. The LED- lights will blink rapidly. When paired, one of the LEDs will stop blinking, while the other continues.

Air 1 Go is now ready to be connected to your bluetooth device.

Touch Commands

Locate the Touch Sensors

Air 1 Go features touch on the flat area on the outside of the headphones. Press this area gently with you fingers to control music, calls and more. For the full overview of touch commands, see the list below:

Both Earbuds

2s Power On
5s Power Off
10s Reset (In the case)

Left Earbud

×1 Volume Up
×2 Volume Down

Right Earbud

×1 Play / Pause
×2 Next Track
×3 Previous Track

×1 Call Answer / Call End
×2 Reject Call
2s Switch Call
2s Siri / Google Assistant

Pro tip: When inserting the earbuds into your ears, try not press against the touch area, as this can turn off the earbud.

Multiple devices

You can pair the Happy Plugs Air 1 products with up to eight different Bluetooth devices. The earphones stores and remembers these pairings. However, you can only be connected to one device at a time, e.g. play music from one Bluetooth device.

To change from one Bluetooth device to another, disconnect the current Bluetooth connection by switching off Bluetooth at the current device and connect to your second Bluetooth device by selecting the Happy Plugs Air 1 product entry in the Bluetooth menu.

When you remove your Happy Plugs Air 1 product from the charge case it will automatically connect to the last device you were connected to.

Supported Devices

Identify your Product

Air 1 Go True Wireless Headphones are compatible with any device equipped with Bluetooth – that includes Apple products, as well as Android based devices.

Air 1 Go supports Bluetooth 5.0 connection and below.

Don’t forget to activate Bluetooth on your device.

Macbook Connection.

For certain Macbook computers, you might experience Bluetooth connection issues or audio issues if you have multiple Bluetooth devices connected at the same time.

Try disconnecting some of the other Bluetooth connections on the computer for improved performance.

Technical Specifications

Technical Specifications

CONNECTIVITY
Bluetooth Version 5.0
Operation Range: Up to 10m / 30 feet

AUDIO
Supported Bluetooth Profiles: HSP, HFP, A2DP & AVRCP
Support Codecs: SBC
Driver: 12 mm
Sensitivity: 102+/- dB
Impedance: 16 ohm
Frequency Response: 20-20k Hz

BATTERY
40 mAh battery in each earbud
400 mAh battery in the charging box
3.5 hours play and talk time in a single charge and 11 hours in total
Standby Time: up to 45h