EBECO 8960280 Snowmat Instruction Manual
- June 12, 2024
- EBECO
Table of Contents
8960280 Snowmat Instruction
Manual INSTALLATION INSTRUCTIONS
8960280 Snowmat
Skapa garantibevis direkt i mobilen
garantera.ebeco.se Welcome
Thank you for choosing Ebeco. For the warranty to be valid, the product must
be installed and handled as indicated in this manual. It is therefore
important that you read the manual.
If you have any questions, please contact us at Ebeco. Call +46 31-707 75 50
or send an e-mail to support@ebeco.se. Feel free to
visit ebeco.com for more information.
Important
The system is a high voltage system and must thus be installed according to
applicable regulations and under the supervision of an authorised electrician.
For the warranty to apply, the guarantee certificate must be correctly and
completely filled in, and signed by an authorised electrician.
Technical specifications
Art.no.| Power| Width| Length| Area| Resistance|
Insulation
---|---|---|---|---|---|---
8960280| 700 W| 0,5 m| 4,2 m| 2,1 m²| 77 Ω| > 10 MΩ
8960281| 1100 W| 0,5 m| 6,9 m| 3,5 m²| 49 Ω| > 10 MΩ
8960282| 1350 W| 0,5 m| 8,5 m| 4,2 m²| 39 Ω| > 10 MΩ
8960283| 2350 W| 0,5 m| 14,4 m| 7,2 m²| 23 Ω| > 10 MΩ
8960284| 2900 W| 0,5 m| 18,0 m| 9,0 m²| 18 Ω| > 10 MΩ
Before you start
- Check that the material supplied corresponds with the information on the delivery note.
- Measure the insulation and resistance of the mat. See values in the table. Enter the values in the test report (at the end of the manual).
- The insulation and resistance of the mat must be measured before and after embedding/surfacing, to check that the mat was not damaged when it was laid. Enter the values in the test report.
- After being placed in the bed of sand, the mat can be covered with ground slabs, paving stones or asphalt. (NOTE: Do not lay in hot asphalt). The mat can also be laid above existing concrete slabs and embedded.
- We recommend that you use the Ebeco Quick Board (art. no. 8960150) for a more energy efficient installation.
- When planning the installation, take into account the fact that the length of the cold cable is 5 m.
- The cold cable splice must be laid in sand/concrete. The heating cable must not be cut. Only the cold cable may be shortened.
- The cable must not touch or cross itself. Minimumdistance 60 mm.
- The cable must not cross any expansion joints.
- Plan how any control sensors are to be positioned. Measuring elements for thermostatic control are to be laid in a plastic tube under the mat. Panelboard with temperature/humidity sensor: refer to the instructions supplied with the panelboard. Snowmat can also be controlled using a timer.
- Fill in and affix the heating cable signs for each junction box. A diagram/photo of the heating mat installation must be on display in the electrical distribution centre.
Installing the Ebeco Snowmat
The installation is described using illustrations. See page 10.
Terms of Warranty
Snowmelt, Snowmat, MI-60 and Multiflex 27*
Ebeco AB provides a 10 year guarantee for defective materials in Snowmelt,
Snowmat, MI-60 and Multiflex 27.
The guarantee only becomes valid under condition that the installation is
carried out by a authorized electrician according to the applicable
regulations and in accordance with installation instructions issued by Ebeco.
This guarantee certificate, including the test record below, must be completed
in its entirety and, along with the materials specification or invoice, must
be signed by the electrician who carried out the installation. Furthermore,
there must be photographs/ sketches that show the mat in its entirety after
laying but before covering.
If defects should arise during the guarantee period, Ebeco AB undertakes to
repair or alternatively replace Snowmelt/ Snowmat/Multiflex at no cost to the
purchaser.
Ebeco AB also undertakes to restore the surface coating to its original
condition after the repair or replacement has been completed. In order to be
able to remedy the fault, the purchaser must have saved or have access to 1 m²
of the existing surface material. For any controls (timer/panelboard), where
defects occur after 3 years, Ebeco AB will supply a new control.
The guarantee does not apply to installations that have been carried out by an
non authorized electrician or alternatively if an non authorized electrician
has carried out modifications or repairs. Nor does the guarantee apply if the
defect has arisen as a result of using incorrect materials and construction or
as a result of incorrect installation. Nor is damage covered that is a result
of vandalism, fire, lightning, water damage or damage caused by negligence,
abnormal usage or as a result of an accident.
In the event of a material defect that is covered by the guarantee Ebeco AB
must be notified.
In the event of the guarantee being invoked, this guarantee certificate with
accompanying invoice of installation, material specification plus completed
and signed test record must be presented.
EBECO AB
Martin Larsson, CEO
- Extended warranty only applies provided that the product has been installed together with Ebeco’s control system.
Test report (Snowmelt, Snowmat, MI-60 and Multiflex 27)
| Before laying| After fixing| After surface coating/ embedding
---|---|---|---
Mat/Cable no. 1-6| Resistance value| Insulation value| Resistance value|
Insulation value| Resistance value| Insulation value
No. 1, E-no:| | | | | |
No. 2, E-no:| | | | | |
No. 3, E-no:| | | | | |
No. 4, E-no:| | | | | |
No. 5, E-no:| | | | | |
No. 6, E-no:| | | | | |
Min. insulation value 10 MΩ.
The system is documented with photos/drawings
Electrical installation carried out by:
Date: ……………………………………………………………….
Signature: …………………………………………………………
according to the attached materials specification.
Installing the Ebeco Snowmat
EBECO AB
Lärjeågatan 11
SE-415 02 Göteborg, SWEDEN
Phone +46 31 707 75 50
ebeco.com
info@ebeco.se
55237 Snowmat vers 1.3 210602
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>