BEOK TDR89 Zigbee Room Thermostat User Guide
- July 14, 2024
- BEOK
Table of Contents
BEOK TDR89 Zigbee Room Thermostat
Product Information
Specifications
- Model: TDR89
- Compatible with: Water Heating, Electric Heating, Gas Boiler
- Power Requirements: WP – 3A, EP – 16A, WPB – 3A
Product Usage Instructions
Installation Procedure
- Connect the power box according to the wiring diagram.
- Separate the power supply from the control board cable.
- Screw the power supply into the box of 86.
- Connect the power board to the control board line, aligning the
- buckle at 30 degrees to complete the installation.
Operating Instructions
- Power on/off: Press to turn on/off the thermostat.
- Press the key to switch between manual and automatic modes.
- In automatic mode, press + or – to adjust the temperature for temporary mode.
- Press key to enter clock setting, use mode key to switch settings options, and adjust values with + and – keys.
- To add or cancel child lock, simultaneously press and hold the + and – keys for 5 seconds.
- For WIFI link, press and hold + button for 5-8 seconds to enter code matching state.
FAQ
Q: What should I do if the thermostat is not connecting to WIFI?
A: If the thermostat is not connecting to WIFI, ensure that you have followed
the correct steps for WIFI connection. Check your network settings and try
resetting the WIFI connection on the thermostat.
TDR89 ZIGBEE THERMOSTAT USER GUIDE
THIS THERMOSTAT IS SUITABLE FOR WATER HEATING, ELECTRIC HEATING AND GAS BOILER
Welcome
Thank you for your trust and support. By adopting higher-end technology and
more perfect technology, your new thermostat will provide you with the right
temperature environment every day in the future, making your life more
comfortable and your living environment more stylish and beautiful. For
detailed instructions on the installation and use of this thermostat, please
read this manual carefully. Please contact a professional to install the
thermostat for you and install and use the product to the extent permitted by
law.
Application
Intelligent digital temperature controller is a floor heating system suitable
for room temperature control and household temperature control. It controls
the operating state of the floor heating equipment by comparing the ambient
temperature with the set temperature, which improves comfort and achieves
energy saving. This digital temperature controller adopts microcomputer
control technology and is equipped with full-screen display touch buttons,
which is elegant in design and easy to use. The thermostat has manual
automatic, programmable and state memory functions.
Product packaging
- Thermostat host 1 PC Qualification certificate 1 PC
- Sensing line (optional) 1 PC Manual 1 PC
- Screw 2 PCS
Product Model
- WP Plumbing 3A
- EP Electric Heating 16A
- WPB linkage, gas boiler 3A
User Notes
- Please read this manual carefully. Improper operation may damage the product or cause dangerous conditions.
- The installation personnel must be well-trained and experienced service technicians.
- After installation, please read this manual carefully and operate the product according to the instructions.
Caution: Risk of electric shock or equipment damage.
Wiring Diagram
Note: WP for water heating; EP for electric heating; WPB for gas boiler
Installation procedure
This product is installed with a standard 86 control switch (in compliance
with European regulations).
1. Connect the power box according to the wiring diagram.
2. Separate the power supply from the control board cable.
3. Screw the power supply into the box of 86.
4. Connect the power board to the control board line, and align the buckle at
30
- Connect the power box according to the wiring diagram.
- Separate the power supply from the control board cable.
- Screw the power supply into the box of 86.
- Connect the power board to the control board line, and align the buckle at 30 degrees to complete the installation.
Description of display & Icon
Operating Instruction
- Power on/off: press to turn on/off the thermostat.
- Press the key to switch between manual and automatic modes.
- In the automatic mode, press + or – to adjust the temperature to enter the automatic temporary mode. This mode runs for only one session.
- Press key to enter the clock setting, press the mode key to switch settings options, and press the + and – keys to adjust the value of each parameter.
- Simultaneously press and hold the + and – keys for 5 seconds to add or cancel the child lock.
- WIFI link: When the thermostat is turned on, press and hold the + button for five or eight seconds, the WIFI icon flashes on the thermostat display, and the thermostat enters the code matching state.
Time programming instructions
Long press the key to enter the programming setting, short press the key to switch options, press the + or – key to adjust the parameters of each option, and press the key to exit and save mode.
Advanced options
In the shutdown state, press the key and key. Press for 5 seconds to enter the
advanced option settings. Press the key to enter the next option, then press
the + and – key to adjust options, and press the key to exit the advanced
option setting mode.
1| Temperature compensation| The default value of the calibration room
temperature is -2 ℃. Press the up and down keys to adjust. The adjustable
range is 9.9 °C to -9.9 ℃.
---|---|---
2| Sensor selection| The temperature sensor is selected as IN by default.
Press the up and down keys to adjust as IN respectively, indicating that the
internal.
3| Modify the temperature limit| The default temperature limit value is 35 ℃.
Press the up and down keys to adjust the range from 5 ℃ to 60 ℃.
4| Temperature difference start| The default temperature difference is set to
1 ℃. Press the up and down keys to adjust the range to 1-10 degrees.
5| Antifreeze function| Set the default anti-freeze function to OFF, display
OFF, press the up key to tum on anti-freeze and display ON.
6| Holiday option and turn off weekly programming| Set the default rest day as
double OFF. Press the up and down keys to adjust It to double OFF (1-5),
single OFF (1-6), no OFF (1 -7) and tum off week programming (OFF).
7| Primary and secondary reverse selection| Set the default main and auxiliary
reversal to 0. Press the up and down keys to adjust 0 to tum off the main and
auxiliary reversal. 01 means auxiliary reverse, 02 means auxiliary reverse, 03
means main and auxiliary reverse, shutdown and antifreeze is not on, stop
output.
8| Passive linkage output delay time| Set the default passive linkage delay
time to 0. Press the up and down keys to adjust the range of 0-5 minutes.
9| Set upper temperature limit| The default value of the set temperature upper
limit is 60℃, and the adjustment range Is 35-95 ℃ by pressing the up and down
keys.
10| Restore Factory Defaults| Set to restore the factory default setting to
display “-”, Press the up button to adjust the display “—”, press the enter
button to restore the factory settings
About wireless connection
Before using the wireless thermostat for the first time, you should set the
signal and configuration through your smart phone or tablet to allow
communication between your connected devices.
WIFI connection: When the thermostat is turned on, press and hold the + button
for 5 seconds, the WIFI icon flashes on the thermostat display, and the
thermostat enters the code matching state.
-
Download the APP
Search for “Tuya” in App market or scan below QR Code to download -
Register Account
If you don’t have an APP account yet, you can choose to register or log in via SMS verification code. Click “Create a new account”, you will enter the Tuya Smart Platform Privacy Policy page. After you click Agree, you will officially enter the mobile phone registration page. The system automatically determines the current country/region. You can also select the country/region manually. After entering your mobile phone number or email address, click “get verification code” . Enter the received verification code, then enter the password, and click “finish” to register successfully. -
Add gateway device
Click “Add Device” or “+”on the top right of the APP homepage, and enter the “Add Device” interface.
-
Thermostat add
-
Display of temperature controller APP interface
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>