AT T PDCU20 20W Quick Charge Power Adapter User Guide
- June 3, 2024
- AT&T
Table of Contents
AT T PDCU20 20W Quick Charge Power Adapter
Thank you for purchasing AT &T PDCU20
Please read this quick start guide before using the device to ensure safe
and proper use.
Features
- Designed to charge smartphones and other accessories.
- Charges 2 devices at the same time with 2 ports for charging:
- 1 Type-C port and 1 QC 3.0 USB outlet
Product Appearance
- PD Type-C Output
- QC 3.0 Output
- Input Plug
Operation instructions
Plug into an alternating current AC 100-240V outlet to provide power to 2 ports charger.
This power adapter is designed for use with an AC 100-240V constant alternation current. A higher or lower voltage is unsuitable for this unit.
Specifications
| Model No. | PDCU20 |
|---|---|
| Input | AC 100-240V 50/60Hz 0.6A |
| PD Output | 5V/3A, 9V/2.22A, 12V/1.67A |
| QC 3.0 Output | 6.5V/3A, 9V/2A, 12V/1.5A |
| Dimensions | 1.65” X 1.61” X 0.9” |
| Weight | 0.11 lbs |
1-YEAR LIMITED WARRANTY
The AT&T brands are used under license. Any repair, replacement, or warranty service, and all questions about this product should be directed to Concept 101 LLC at www.att.com/electronics or call 1(888) 920-8680 from the USA or Canada. Concept 101 LLC warrants that the product will be free from defects in material, parts, and workmanship for the period of one (1) year from the date of purchase. Concept 101 LLC agrees that it will, at its option, replace the defective product with either a new or remanufactured product equivalent to your original purchase during the warranty period.
Please be advised the returned product must carry the proof of purchase.
Exclusions and limitations
Concept 101 LLC does not warrant that the product will work properly in all
environmental conditions, and makes no warranty and representation, either
implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose other than the purpose
identified within this user’s manual. Concept 101 LLC has made every effort to
ensure that this user’s manual is accurate and disclaims liability for any
inaccuracies or omissions that may have occurred. Information in this user’s
manual is subject to change without notice and does not represent a Commitment
on the part of Concept 101 LLC. Concept 101 LLC reserves the right to make
improvements to this user’s manual and/or to the products described in this
user’s manual at any time without notice. If you find information in this
quick start guide that is incorrect, misleading, or incomplete, please contact
us through our website.
Compliance with FCC Regulations
The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for assistance.
AT &T
www.att.com/electronics
2022 Concept 101 LLC. All Rights Reserved. AT&T and the AT&T logo are trademarks of AT&T Intellectual. Property licensed to Concept 101 LLC, New York, New York 10018. Printed in China. Issue 11 AT&T 03/2022.
The ‘Quick Charge icon and Quick charge are registered trademarks of Qualcomm Technologies, Inc Other trademarks and trade names are those of their respective owners.