Perlick CR-ACC-D1 Column Dual Installation Kit Handle To Handle with Heater Instructions
- June 12, 2024
- Perlick
Table of Contents
Perlick CR-ACC-D1 Column Dual Installation Kit Handle To Handle with Heater
Instructions
Instruction
STEP #1: OPEN THE DOORS TO THE CABINETS. GRAB BOTH SIDES OF THE FRONT
GRILL PLATE AND PULL STRAIGHT OUT IN ORDER TO POP THE CLIPS OUT OF THE LATCHS.
DO THIS TO BOTH CABINETS.
STEP #2: DETERMINING WHICH CABINET WILL BE ON THE LEFT SIDE. ATTACH THE “SIDE BY SIDE HEATER ASSEMBLY” (1010469) TO THE RIGHT SIDE OF THE LEFT CABINET WITH (3) M50050-466.
STEP #3: ONCE THE HEATER ASSEMBLY IS ATTACHED, SNAP (1) 1-1/4″ BUSHING
INTO THE SIDE OF THE CABINET.
STEP#4: RUN THE WIRES FROM THE HEATING ASSEMBLY THROUGH THE 1- 1/4″ BUSHING AND SNAP THE END CONNECTOR INTO THE CUT OUT OF BRACKET 1009975-1
STEP #5: ATTACH BRACKET 1009975-1 WITH (2) M50095-122. CAUTION: DO NOT PINCH WIRES FROM HEATING ASSEMBLY.
| ITEM NO. | PART NUMBER | DESCRIPTION | Default/QTY. |
|---|---|---|---|
| 1 | 1008781 | SCREW, M6 X 12MM, THRD | 8 |
| 2 | 1009975-1 | BRACKET, MOUNTING, MACHINE COMP. WIRE HARNESS, COLUMN | 1 |
| 3 | 1010469 | SIDE BY SIDE HEATER ASSEMBLY, COLUMN | 1 |
| 4 | 1010546 | M5x10 MACH SCR, LOW HEAD, NBK PART NO: SSH-M5-10 | 6 |
| 5 | 1010667 | BUSHING, SPLIT, 1-1/4″ HOLE, BLACK, HEYCO 2881 | 1 |
| 6 | 1012862 | POWER CORD KIT | 1 |
| 7 | 1013719-1 | BRACKET, ATTACHING, COLUMN, FOR SIDE BY SIDE INSTALLS | 4 |
| 8 | 1015035-1 | CENTER TRIM, SIDE BY SIDE INSTALL, COLUMN | 1 |
| 11 | M50050-466 | #10 X 1/2″ PH Truss Head SMS #410 S.S., Type “AB”, | 11 |
| 12 | M50095-122 | Screw, Sheet Metal, #10-16 x 1/2″ Thin-Lock TM, PH | |
| Undercut Pan | 2 | ||
| D | 47.75″ WAS 49″ | 2/05/2019 | |
| --- | --- | --- | |
| C | UPDATE |
INSTRUCTION
LAYOUT| 5/30/2018
STEP #6: SELECT THE CABINET THAT WILL BE PLACED ON THE RIGHT SIDE. SECURE
(1) 1013719-1TO THE FRONT BASE WITH (2) 1008781 SCREWS
STEP #7: REMOVE ALL PROTECTIVE FILM FROM THE CENTER TRIM (1015035-1).
STEP #8: ATTACH THE CENTER TRIM TO LEFT SIDE OF THE CABINET THAT WILL BE
ON THE RIGHT, WITH (6) 1010546. BEFORE FULLY TIGHTENING SCREWS, MAKE SURE THE
CENTER TRIM SITS FLUSH WITH THE CABINET FACE.
STEP #9 : MOVE BOTH CABINETS DIRECTLY NEXT TO EACH OTHER SO THAT THE LEFT CABINET COMES IN CONTACT WITH THE CENTER TRIM.
STEP #10: SECURE BOTH CABINETS TOGETHER BY SECURING THE “ATTACHING BRACKET (1013719-
- ” PREVIOUSLY SECURED TO THE RIGHTCABINET, TO THE LEFT CABINET WITH (2) 1008781 SCREWS
STEP #11: SECURE BOTH CABINETS TOGETHER AT THE TOP WITH (2) 1013719-1 AND
(8) M50050-466
STEP #12: SECURE BOTH CABINETS TOGETHER AT THE BACK WITH (1) 1013719-1 AND (4) 1008781
STEP #13: ONCE ALL BRACKETS HAVE BEEN SECURED IN PLACE, ATTACH THE FRONT GRILLS BACK ONTO THE UNT.
STEP #14: PLUG POWER CORD (1012862) INTO HEATING ASSEMBLY CONNECTOR NOTE: HEATING ASSEMBLY CAN UTILIZE SAME ELECTRICAL CIRCUIT AS THE CABINET
PERLICK CORPORATION
MILWAUKEE, WI 53223
PROPERTY OF THE PERLICK CORP.
NOT TO BE COPIED OR USED DETRIMENTAL TO OUR INTERESTS
D:\Perlick\Engineering\Projects\Refrigeration\1601802\CAD Files\1014974.slddrw
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>