GOLDEN LIGHTING 3072-3P NB Athena 3 Light Natural Black Pendant Ceiling Light Instruction Manual
- June 12, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 3072-3P NB Athena 3 Light Natural Black Pendant Ceiling
Light Instruction Manual
DIMENSIONS
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the best lighting in your space, remember to layer your lighting. This ensures that your space will have both task and ambient lighting. Coordinating fixtures like sconces, flush mounts, and pendants can help you meet your layered lighting needs and reinforce your desired aesthetic. Install the lights with dimmers that allow you to control the level of light output at any given moment.
Get function and style! Browse our site for coordinating lights and expert lighting advice. To help create the perfect look, visit www.GoldenLighting.com.
Love your light and want to show it off? Follow us, share a picture, and tag us on Social…………..
Assembly Instructions
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
**Get help, quick tips, and explore curated content
**
PARTS
For Customer Service, contact the place of purchase to arrange for replacement parts
IMPORTANT
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Take the mounting strap (A) assembly from the parts
bag. One end of nipple (F) should be attached to mounting strap (A)
with a washer and hex nut ( C and D) in place. The other end should have
canopy loop (H) attached. Use a screwdriver and mounting screws (B) to
attach mounting strap (A) to the junction box. (Note: When mounting strap
(A) is properly installed, about half of the exterior threads of nipple
(F) are exposed, allowing canopy loop (H) to fit snugly onto nipple
(F). You may want to test to ensure that with canopy (G) in place, canopy
loop collar (I) fits onto nipple (F). After testing, remove everything
from the nipple (F) and place aside for later.
ASSEMBLING THE FIXTURE
Pull the wires through post (M) until taut and thread top loop (L) onto
post(M). 3. Measure to determine the correct number of chain links needed for
proper hanging height. If necessary, use a pair of pliers to open and remove
any excess chain (J). Attach one chain connector (K) to each end of chain
(J). 4. Connect one of chain connectors (K) to top loop (L) and close
the chain connector. Feed the fixture’s wires up through the chain (every
three links or so), pulling the wires until taut. Use the free chain connector
(K) to attach chain (J) to canopy loop (H). Untwist canopy loop collar
(I) to allow canopy (G) to drop down onto the chain/wire.
CONNECTING THE WIRES
Have an assistant support the fixture’s weight while completing the wiring.
Refer to the wiring diagram and attach the fixture’s wires to the power supply
wires from the junction box. Attach the fixture’s wires to the power supply
wires from the junction box. Connect Hot to Hot (transparent wire with black
inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with
white inner thread, white, or ribbed wire), and Ground to Ground (transparent
wire with green inner thread, green wire, or copper). Twist the ends of the
wire pairs together, and then twist on a wire connector. Make sure all twists
are in the same direction. If there is no house ground wire coming from the
junction box, locate ground screw (E) on the mounting bracket/mounting
strap and wrap the fixture’s ground wire around the ground screw. Use a
screwdriver to tighten the top of ground screw (E) onto the wires and into the
mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE INSTALLATION
Push canopy (G) up to the ceiling and slide canopy loop collar (I) up
beneath the canopy. Tightly thread canopy loop collar (I) onto canopy loop
(H) to secure canopy (G) in place. 7. Install light bulbs (not
included) into candle sleeves (P) in accordance with the fixture’s
specifications. Do not exceed the maximum wattage. Your installation is now
complete. Turn on the power and test the fixture.
Costumer Support
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>