vtech CD1100 Cordless Telephone User Guide

vtech CD1100 Cordless Telephone

Product Information

The CD1100 is a telephone equipment manufactured by VTech. It comes with important safety instructions to ensure user safety and reduce the risk of fire, electric shock, and injury. The telephone is covered by a two-year warranty against any defects in materials or workmanship from the date of purchase. The warranty is valid only for the original purchaser and is not transferable. Breakages to the LCD screen are not covered by the warranty.

Product Handset Overview

The handset features various buttons and switches for different functions:

• R (FLASH): Press during a call to answer an incoming call when you receive a calling alert.
• Dialing keys: Press to enter the phone number you want to dial.
• RINGER switch: Switch to turn the ringer ON or OFF.
• Switch hook: When held down, the telephone is in idle mode. When released, the telephone is ready to make a call.
• REDIAL: Press to redial the last number dialed.
• DIAL switch: Switch to choose touch-tone (TT) dialing or pulse (DP) dialing.
• Volume switch: Switch to set the handset listening volume to high, medium, or low.

Product Usage Instructions

Telephone Facility

• Your telephone base can be mounted on a wall or placed on a table. Here are the installation steps:

Mount the phone on the wall

1. Route the excess telephone line cord through the channel on the bottom of the telephone base, and then plug the other end of the telephone line cord into a telephone wall jack.
2. Place the handset on the telephone base, and then align the holes on the telephone base against the mounting studs.
3. Push the telephone down until it is securely in place.

Wall mount to tabletop installation

1. Slide the telephone base up and remove it from the wall plate. Unplug the telephone line cord from the wall.
2. Place the telephone base on the table and reverse the handset tab.
3. Plug the telephone line cord into a telephone wall jack and put the handset on the telephone base.

Product Settings

Ringer Volume

• Use the RINGER switch on the handset to set the ringer ON or OFF.
• The ringer volume is set to ON by default. If it is set to OFF, this telephone will not ring when there is an incoming call.

Dial Mode

• Choose the suitable dial mode before using this telephone. If you have touch-tone dialing service, slide the DIAL switch to TT.
• If you have pulse (rotary) service, slide the DIAL switch to DP.

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen sink, swimming pool).
5. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.
6. Do not expose the telephone to direct sunlight or extreme cold environment. Do not put the telephone close to heating sources such as radiators, cookers, etc.
7. Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
8. Unplug this product from the wall outlet and refer servicing to VTech/distributor under the following conditions:
   • When the power supply cord or plug is damaged or frayed.
   • If the product does not operate normally by following the operating instructions.
   • If the product has been dropped and the cabinet has been damaged.
   • If the product exhibits a distinct change in performance.
9. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home or office, consult your dealer or local power company.
10. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
11. Do not use the telephone to report a gas leak in the vicinity of the leak.

Disposal of Old Equipment and Batteries (WEEE)

Only for European Union and countries with recycling systems. These symbols (a, b) on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries must not be mixed with general household waste. For proper treatment, recovery and recycling of old products and batteries, please take them to applicable collection points in accordance with your national legislation. By disposing of them correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment.

For more information about collection and recycling, please contact your local municipality. Penalties may be applicable for incorrect disposal of this waste, in accordance with national legislation. VTech Telecommunication Ltd. is registered at Stiftung elektro-altgeräte-register under WEEE-Reg. number DE 52869849.

Product disposal instructions for business users

• If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other countries outside the European Union

• These symbols (a, b) are only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

Note for the battery symbol

This symbol (b) might be used in combination with a chemical symbol. In this case it complies with the requirement set by the Directive for the chemical involved.

Recycle your device (WEEE directive 2012/19/EU)

• The WEEE logo appears on the product to indicate that this product must not be disposed off or dumped with your other household wastes. You are liable to dispose of all your electronic or electrical waste equipment by relocating over to the specified collection point for recycling of such hazardous waste.

Approval and conformity

• This product is intended for use within Europe and the UK. This equipment complies with the essential requirements to EU’s Electromagnetic compatibility Directive (2014/30/EU) and the UK’s Electromagnetic compatibility Regulations SI 2016/1091 on telecommunication equipment.
• VTech Telecommunication Ltd. hereby declares that this telephone CD1100 is in compliance with the essential requirements and other relevant provisions of EU’s Electromagnetic compatibility Directive (2014/30/EU) and the UK’s Electromagnetic compatibility Regulations SI 2016/1091.
• The declaration of conformity may be viewed at https://www.vtech.com/rtte-directive.

The symbol confirms the conformity of the telephone and the above directive.

• Importer: Snom Technology GmbH.
• Wittestraße 30G, 13509, Berlin, Deutschland.
• Manufacturer: VTech Telecommunications Ltd.
• 23/F, Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong.

VTech Product Warranty

Thank you for purchasing this telephone from VTech.

1. The product is covered by a two-year warranty from the date of purchase (date from which the warranty period starts), against any defects in materials or workmanship.
2. The product may be returned to the place of purchase.
3. During the limited warranty period, VTech’s authorized service representative will examine the product and if it is found to be defective due to faulty materials or workmanship, will replace the product at their discretion
4. If the product covered by this warranty is damaged due to misuse, modification or unauthorized repair, or because of faulty batteries, battery discharge or incorrect electrical connections, then this warranty becomes void.
5. This warranty is personal to the original purchaser and is not transferable.
6. Breakages to the LCD screen are not covered by the warranty.

Please retain your original sales receipt as proof of purchase.
To obtain warranty service, please visit our website at www.vtechphones.eu.

Handset overview

Telephone installation

Your telephone base comes in wall mount position. You can mount your telephone on a wall or place it on a table.

Mount the telephone on the wall

1. Route the excess telephone line cord through the channel on the bottom of the telephone base, and then plug the other end of the telephone line cord into a telephone wall jack.
2. Place the handset on the telephone base, and then align the holes on the telephone base against the mounting studs. Then push the telephone down until it is securely in place.

Wall mount to tabletop installation

1. Slide the telephone base up and remove it from the wall plate. Unplug the telephone line cord from the wall.
2. Place the telephone base on the table and reverse the handset tab as shown.
3. Plug the telephone line cord into a telephone wall jack and put the handset on the telephone base.

Settings

Ringer volume

• Use the RINGER switch on the handset to set the ringer on or off.
• The ringer volume is set to ON by default. If it is set to OFF, this telephone will not ring when there is an incoming call.

Dial mode

• Choose the suitable dial mode before using this telephone.
• If you have touch-tone dialing service, slide the DIAL switch to TT. If you have pulse (rotary) service, slide the DIAL switch to DP.

Note: There are some occasions that you need to switch between touch-tone dialing (TT) and pulse dialing (DP) during a call such as some tone activated computer systems (for example, telephone banking). In this case, slide the DIAL switch to change the dial mode while on a call without disconnecting it.

Handset volume

• Slide the volume switch at the side of the handset to adjust the listening volume. You can set the listening volume to high, medium or low.

Operations

Make a call| Pick up the handset and wait for a dial tone. Then dial the telephone number.
---|---
Answer a call| When there is an incoming call, pick up the handset.
End a call| Place the handset back to the telephone base.
Redial

| This telephone stores the last telephone number dialed. The redial number can be up to 32 digits.

•      Lift the handset and then press REDIAL to dial the last number dialed.

Erase the last number dialed

For privacy, you can erase the redial memory.

•      Lift the handset, then press 1 and hang up.

: If the last number dialed has more than 32 digits, the number will not be saved in the redial memory.

Flash

| When you subscribe to call waiting service from your telephone service provider, you hear an alert tone if there is an incoming call while you are already on a call. Contact your telephone service provider for more information about subscriber services.

•      Press R to put the current call on hold and take the new call.

•      Press R at any time to switch back and forth between calls.

Scan the QR code for support information

Specifications are subject to change without notice.

©2023 VTech Telecommunications Ltd.
All rights reserved. 03/23. CD1100_UMEU 4 langs_V1

References

• VTech Telecom Products European Official Site
• Product Support & R&TTE Compliance | VTech
• VTech Telecom Products European Official Site

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>