kanto TE300 Extendable Tilting TV Wall Mount User Manual
- June 12, 2024
- Kanto
Table of Contents
kanto TE300 Extendable Tilting TV Wall Mount User Manual
Thank you for choosing Kanto
Read these instructions fully before assembly and installation. Make sure there are no defective or missing parts. Do not use defective parts. Kanto cannot be liable for property damage or injury caused by incorrect mounting, incorrect assembly, lifting or incorrect use of this product. If there is hardware missing, or if you are uncertain whether a part is defective, please contact Kanto directly using one of the methods below
CAUTION
The maximum loading weight is 150 lb (68 kg). This mount is intended for use
only with the maximum weights indicated. Use with products heavier than the
maximum weights indicated may result in instability causing possible injury.
The wall you plan to affix the Kanto mount to must be able to support more
than 5 times the weight of the television and the mount combined. Do not use
this product for any purpose other than to mount a VESA compliant TV on a
vertical surface as outlined in this manual. This Kanto mount is not certified
by or affiliated with Video Electronics Standards Assoc (VESA). Improper
installation may cause damage to your TV or serious injury. This product
should not be mounted on steel stud walls or cinder block walls. Consult a
qualified installation contractor if you are unsure about the type of wall you
may have.
Supplied Parts and Hardware
A: M4 x 16 mm
B: M5 x 16 mm
C: M5 x 30 mm
D: M6 x 16 mm
E: M6 x 35 mm
F: M8 x 20 mm
G: M8 x 35 mm
H: M8 x 50 mm
I: 5 mm
J: 10 mm
K: 14 mm
L: M4 / M5 / M6
M: M8
N: Concrete Anchor
O: M8 x 50 mm
Required Tools
Socket Set
Phillips Screwdriver
Pencil
Level
Measuring Tape
Drill
Stud Finder
Wood Bit
Hammer
Masonry Bit
Project Overview
IMPORTANT!: Please read this entire document before attempting assembly.
- Select TV Screws and Spacers
- Select Spacers for Irregular TVs
- Attach TV Brackets
- Assemble Wall Plate
- Mount Wall Plate Assembly
- Hang TV
- Level TV
- Finalize Adjustments
- Remove TV
If you have any problems or difficulties while following these
instructions, please contact Kanto directly:
Email: support@kantoliving.com
Toll Free: US & Canada: 1-888-848-2643
Select TV Screws and Spacers
A–H Select Screws
The back of your TV has 4 screw holes in a square or rectangular pattern. This is where the mount will attach to your TV. Kanto provides several sizes and lengths of screws. This guide will help you select the right screws for your TV. You will only use 4 of the provided screws to attach your TV – the rest are not needed.
Ι–K Select Spacers
Plastic spacers are also provided in 3 thicknesses to allow the mount to
workwith curved TVs, and TVs that have recessed mount holes, protrusions, or
inputs in the way. They can also be used to prevent the TV screws from going
too deep and damaging your TV. You may not need spacers for your TV.
Select Spacers for Irregular TVs
Spacers can be used to provide clearance around protrusions on the back of your TV, or to accommodate a curved TV. You may need to use longer screws.
Attach TV Brackets
WARNING
Only applicable if using M4 / M5 / M6 screw
Optional
Assemble Wall Plate
5a. Mount Wall Plate Assembly (Wood Stud Wall)
Mount height depends on TV size, viewing position, and personal preference
WARNING
Do not use concrete anchors in drywall or wood stud walls
CAUTION
Make sure the supporting surface will support the load limits outlined in
the caution on page two
5b. Mount Wall Plate Assembly (Concrete Wall)
Mount height depends on TV size, viewing position, and personal preference.
WARNING
Do not use concrete anchors in drywall or wood stud walls.
CAUTION
Make sure the concrete or brick wall is at least 4” thick. Make sure the anchor is seated completely flush with the concrete surface even if there is another layer of material, such as drywall. If drywall is over 5/8” thick, custom lag bolts must be used. Concrete must be a minimum of 2000 psi in density
Hang TV
Level TV
Finalize Adjustments
Remove TV
INSTRUCTION
kantoaudio.com”
Kanto Solutions
Kanto Audio
kantoaudio
@kantoaudio
Kanto Living
Limited Warranty to Original Purchaser
Kanto Living Inc. (Kanto) warrants the equipment it manufactures to be free from defects in material for the limited warranty period of 5 years.
If equipment fails because of such defects and Kanto is notified within 5 years from the date of shipment with proof of original invoice from an authorized reseller, Kanto will, at its option, provide replacement parts or replace the equipment, provided that the equipment has not been subjected to mechanical, electrical, or other abuse or modifications. Any replacement parts or replacement units are warranted for 90days from the day of reshipment to the original purchaser.
Customers will be responsible for obtaining a Return Authorization Number and paying shipping costs to return product to a Kanto location or authorized depot. If the equipment is covered under the warranty provisions above, Kanto will replace parts or provide a replacement unit, and be responsible for shipping costs to the customer. Please keep the original packaging to prevent damage to the product during shipping. Insuring your shipment is also recommended.
The information in the manual has been carefully checked and is believed to be accurate. However, Kanto assumes no responsibility for any inaccuracies that may be contained in the manual. In no event will Kanto be liable for direct, indirect,special, incidental, or consequential damages resulting from any defect in the equipment, even if advised of the possibility of such damages. This warranty is in lieu of all other warranties expressed or implied, including without limitation, any implied warranty, including any warranty of merchantability and fitness for any particular purpose, all of which are expressly disclaimed.
Costumer Support
www.kantomounts.com
support@kantoliving.com
Toll Free: 1-888-848-2643
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>