saxby IM_75531 Reeve Connect Instruction Manual

Instruction manual
Reeve Connect Batten
75531, 75532, 75533, 75534

Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.

Warning

This power supply is Double Insulated and does not require connection to an Earth circuit.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Check the pack and make sure you have all the parts listed.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Layout

Plan the desired layout of these fittings carefully, ensuring the cables will reach the distance between the junction box and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber sheathed cable.
The mains supply cable must have a minimum cross sectional area of 1.0mm2
Cables must be protected using suitable conduit or plastic trunking.

Installation

Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
Note that the switch is turned off before installation.
Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.
The ceiling surface must be flat and smooth to ensure a good fit.

• Refer to the diagram below. Decide on the location of the product. Measure the distance between the mounting bracket location slots, mark the location of the fixing holes on the mounting surface.
• Drill holes and fit supplied wall plugs (suitable for masonry only – for other surfaces use appropriate fixings).
• Attach product to mounting brackets by pushing until securely held.

Max number of interconnect with model:
75531: Max. 15pcs
75532: Max. 12pcs
75533: Max. 12pcs
75534: Max. 8pcs

Wiring

If not fitting to a plug then the product must be wired to a IP68 outdoor rated terminal block. We recommend item 90131/90132 (0urtdoor rated terminal block).
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect to the quick fit connection block in the following way:

Check that…

• You have correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
• Reseal the approved outdoor rated external terminal block.

Technical data

75532 – 36W LED SMD, 6500K
75533 -45W LED SMD, 6500K
75534 -55W LED SMD, 6500K
These products contain a light source of energy efficiency class F.
| Non-replaceable light source
| Non-replaceable control gear
****| Conformity with all relevant UKCA Directive requirements.
| Conformity with all relevant EC Directive requirements.
| The power supply is Double Insulated and does not require connection to an Earth circuit.
| Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
| This product is not suitable for dimming.
| Caution! Risk of electric shock!
| This procuctisrated at IP65
| This rocuct is rated at 1Ko8.

Care and Safety
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.

For further information, please visit https://www.lighting-inf0.co.uk/75531
V5 21/01/2022
UK Manufacturer: BH17 7BY
EU Manufacturer: Brilliant AG,
Brilliantstrasse 1, D-27 442 Gnarrenburg

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>