Circutor ePick GPRS NET DataBox Gateway Instruction Manual

: June 12, 2024
: Circutor

Table of Contents

ePick GPRS NET Data Box Gateway
DESCRIPTION
INSTALLATION
START-UP
Technical features
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ePick GPRS NET
GATEWAY FOR Data Box PLATFORM

ePick GPRS NET Data Box Gateway

This manual is a ePick GPRS NET installation guide. For further information, please download the full manual from the CIRCUTOR web site: www.circutor.com
IMPORTANT!
The unit must be disconnected from its power supply sources before undertaking any installation, repair or handling operations on the unit’s connections. Contact the after-sales service if you suspect that there is an operational fault in the unit. The unit has been designed for easy replacement in case of malfunction.
The manufacturer of the unit is not responsible for any damage resulting from failure by the user or installer to heed the warnings and/or recommendations set out in this manual, nor for damage resulting from the use of non-original products or accessories or those made by other manufacturers.

DESCRIPTION

ePick GPRS NET is a gateway designed to communicate with machines and sensors, collect and store their data and send it to the web for processing.
The device features Ethernet and RS-485. ePick GPRS NET can communicate with the DataBox platform via GPRS or via the customer’s Ethernet/router.

INSTALLATION

The epic GPRS NET has been designed for assembly on DIN rail.
IMPORTANT!
Take into account that when the device is connected, the terminals may be hazardous to the touch, and opening the covers or removing elements may provide access to parts that are dangerous to the touch. Do not use the device until it is fully installed.
The device must be connected to a power circuit protected by gL (IEC 60269) or M class fuses between 0.5 and 2A. It must be fitted with a circuit breaker or equivalent device to disconnect the device from the power supply.
The epic GPRS NET can be connected to a device (machines, sensors …) via Ethernet or RS-485:

Ethernet:
A category 5 or higher network cable is required for the Ethernet connection.
RS-485:
The connection via RS-485 requires a twisted communication cable to be connected between terminals A+, B- and GND.

START-UP

The device must be configured from the Circutor Databox web platform, after it is connected to the auxiliary power supply (terminals L and N). See Instruction Manual M382B01-03-xxx.

Technical features

Power supply	CA /AC	CC/DC
Rated voltage	85 … 264 V ~	120… 300 V ****
Frequency	47 … 63 Hz	–
Consumption	8.8… 10.5 VA	6.4… 6.5 W
Installation category	CAT III 300 V	CAT III 300 V

M2

Dimensions| 87.5 x 88.5 x 48 mm
Weight| 180 g.
Surround| Polycarbonate UL94 Self-extinguishing V0
Attachment| Carrel DIN / DIN rail
Electrical safety
Protection against electric shock| Double insulation class II
Isolation| 3 kV ~
Norma’s **
UNE-EN 61010-1, UNE-EN 61000-6-2, UNE-EN 61000-6-4**

Circutor ePick GPRS NET DataBox Gateway - Fig3 Note: Device images are for illustrative purposes only and may differ from the actual device.

LEDs

Power| Device status
ON
Green color : Device ON
RS-485| RS-485 Communications status
ON
Red color : Data transmission
Green color : Data reception
Modem| Communications status
ON
Red color : Data transmission
Green color : Data reception

Circutor ePick GPRS NET DataBox Gateway - Fig1

Terminal connections designations

Circutor ePick GPRS NET DataBox Gateway - Fig2

CIRCUTOR SAT: 902 449 459 (SPAIN) / (+34) 937 452 919 (out of Spain)
Vial Sant Jordi, s/n
08232 – Viladecavalls (Barcelona)
Tel: (+34) 937 452 900 – Fax: (+34) 937 452 914
e-mail: sat@circutor.com
M383A01-44-23A