AURA BEANbuds Wireless Headset User Manual
- June 12, 2024
- Aura
Table of Contents
AURA BEANbuds Wireless Headset
Packing List
Specifications
Farbuds
- Product name Wireless headset
- Bluetooth version 5.3
- Communication distance 10m
- Water proof level IPX4
- Horn 10mm moving coil unit* 2
- Frequency response 20Hz-20KHz
- Sensitivity 108dB ‡3dB SPL (at 1kHz/1mW)
- Impedance 160+15%
- Supported protocols HFP/HSP/A2DP/AVRCP/AAC
- Microphone sensitivity -42dB+3dB (at 1kHz ref 1V/Pa)
- Microphone frequency response 20Hz – 20kHz
- Audio coding SBC/AAC
- Battery life (with charging case) 32H
- Charging time 2H
- Battery capacity 50mAh*2
- Weight 4.7g
Charging Case
- Charging port Type-C
- Charging time 2H
- Battery capacity 320mAh
- Charging times full charge 2.5times for earbuds
- Weight 26.2g
Product Introduction
LED Indicators & Controls
Light Indicator Earbuds Controls
Pairing
Getting Started
Note: When using for the first time, please remove the protective film
from the charging case. And charge the earbuds, it takes about two hours to
fully charge.
Turn On Off
Long press the control panel of the earbuds for 5 seconds to turn on/off.
(Both the left and right earbuds can be independently turned on/off or
connected.)
First Pairing
- Open the charging case and put on the earbuds. You will hear “power on”.
- Turn on the Bluetooth panel on the device you want to pair. Look for: “Aura BEANbuds”
- Select “Aura BEANbuds” and click “Pairing”. You will hear “connected” for successful pairing.
Second Pairing
After the initial pairing, the earbuds will auto-connect to the paired device
via Bluetooth when you put them on, and you will hear a prompt tone saying
“connected”
Using the Left/Right Earbud Only
Put on single earbud (R/L) and pair it with your device using the paring steps
outlined above Long press for 5 seconds to control the power on/off.
Factory reset
To reset the earbuds to their factory settings and clear all pairing memories
of paired devices, tap either earbud 5 times until you hear the “denden”
prompt.
Wake Up
Wear
Connect
Q&A
Earbud bluetooth cannot be searched or lost connection.
- Place the earbuds inside the charging case, close the lid, wait for 8 seconds, and then reopen the lid to initiate pairing.
- Refreshing or restarting requires conect the device’s Bluetooth (phone/ computer)
- 5-tap on either earbud to restore the earbuds to factory setting, than pairing again.
The earbuds cannot charge.
- Please check if the charging case has power.
- Please check if there are any foreign objects in the earbuds placement area of the charging case.
- The rated input of the charging case is 5V- 200mA. Do not use high-power adapter for charging.
Why can listen to music but not make or receive phone calls?
It may be that the “headset call audio” switch on your phone is not turned on.
You need to turn it on in your phone’s settings.
Why is the sound weak?
It may be that the Earbuds are not wear in deeply enough. Please rotate the
earpbuds and insert them as deeply as possible into the ear canal for better
sound. Check the wearing display picture. I am unable to find a solution to
the issue listed. Kindly contact our customer service team online via the
purchase order page. We will respond within 24 hours. Thank you for your
understanding and cooperation.
Warm tips : the volume shall not be too high in daily use, otherwise it
is easy to damage your hearing. Please develop a good listening habit. Take
off your headset every hour to let vour ears relax and rest.
Names and contents of hazardous substances in the product
This table is prepared according to SJ/T 11364.
- O: It means that the content of the toxic and hazardous substance in all the homogeneous materials of the component is below the limit requirements specified in GB/T 26572.
- x: It means that the content of the hazardous substance in a homogeneous material of the component exceeds the limit requirements specified in GB/T 26572.
Note: the product adopts the environmental protection design concept
toeffectivelv control the hazardous substances. “X” indicates that the
hazardous substances can not be replaced due to the limitation of technical
development level.
Environmental friendly service life
Identification refers to the period (ten years) during which the harmful
substances in electronic and electrical products will not leak or mutate
under normal use conditions, and the user’s use ofthe electronic and
electrical products will not cause serious pollution to the environment or
serious damage to people and property.
Notes
- Please do not put the product in any place with high temperature, humidity, strong acid, etc., so as to avoid failure.
- If the product is not used for a long time, please pay attention to charging the charging bin in time to avoid any affect on the battery service life.
- Improper battery replacement may lead to an explosion risk. It can only be replaced by the same type of battery.
FCC
FCC Statement BT
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FCC ID: 2A3MH-BEAN2
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>