SmartGen CMM366A-WIFI Cloud Monitoring Communication Module User Manual

**SmartGen CMM366A-WIFI Cloud Monitoring Communication Module User Manual

**

 Chinese trademark
English trademark
SmartGen — make your generator smart
SmartGen Technology Co., Ltd.
No.28 Jinsuo Road
Zhengzhou
Henan Province
P. R. China
Tel: +86-371-67988888/67981888/67992951
Tel : +86-371-67981000 (overseas)
Fax: +86-371-67992952
Web: www.smartgen.com.cn/
www.smartgen.cn/
Email: sales@smartgen.cn
All rights reserved. No part of this publication may be reproduced in any material form (including
photocopying or storing in any medium by electronic means or other) without the written permission of the copyright holder.
Applications for the copyright holder’s written permission to reproduce any part of this publication should be addressed to SmartGen Technology at the address above.
Any reference to trademarked product names used within this publication is owned by their respective companies.
SmartGen Technology reserves the right to change the contents of this document without prior notice.

Table 1 – Software Version

OVERVIEW

CMM366A-WIFI Cloud Monitoring Communication Module is WIFI wireless network
communication protocol switch module which can achieve genset (with SCI) connect to Internet. After logging into cloud server, module will receive corresponding genset controller communication protocol from cloud server. And module gains genset data via RS485 port, USB port, LINK port or RS232 port then send the data to corresponding cloud server through WIFI wireless network for achieving user’s real-time monitoring to running status and searching of running records via APP (IOS or Android) and PC terminal devices.
CMM366A-WIFI module not only can achieve genset monitoring but also can insert some digital alarm input/output signal to achieve monitoring of generator room entrance guard, guard against theft and fire facilities.

PERFORMANCE AND CHARACTERISTICS

• Connect to cloud server via WIFI wireless network, one to one monitoring;  Multiple ports for communication with genset control module: RS485, RS232, LINK and USB (Host); can
• monitor great majority genset control modules of international first-class brands;
• Widely power supply: DC (8~35)V, can direct use genset built-in battery;
• With ARM-based 32-bit SCM, high integration of hardware and strong programming ability;
• Include with GPS locate function to achieve location information and locate genset;
• Take JSON network data communication protocol, upload real-time data variation and take compression algorithm to vastly reduce network flow at the same time;
• Users can upload monitoring data to the server for analyzing based on the user-defined “historydata upload interval”;
• When alarm occurs it can upload data to server immediately;
• 2 auxiliary digital input ports which can receive external alarm signal;
• 1 auxiliary relay output ports which can output various alarm signals;
• Perpetual calendar and clock functions;
• Power and multiple communication status indicators on front panel that working status is clear at a glance;
• Lamp test function;
• Parameter adjust function: users can adjust parameters via USB port;
• Take standard π-type 35mm guide-rail installation or screw-fixed installation that the module can be installed in the genset control box;
• Modular design, self extinguishing ABS plastic shell, light weight, compact structure with easy installation.

SPECIFICATION

PANEL AND TERMINAL DESCRIPTION

PANEL INDICATOR AND BUTTONS

Fig.1 – Panel Indicators
Table 3 – Indicators Description

Icon

|

Note

---|---
POWER/ALARM| Green LED Light: Power supply normal; connect with cloud server success;

Red LED Light: Common alarm indicator.

RS485(Red)

| Normally Extinguish: RS485 disabled; Normally Light: Communication fail;

Blink: Communication normal.

USB(Red)

| Normally Extinguish: USB(Host) disabled; Normally Light: Communication fail;

Blink: Communication normal.

WIFI(Red)

| Extinguish: CMM366A-WIFI login with server unsuccessfully; Normally Light: Communication fail;

Blink: Communication normal.

LINK(Red)

| Normally Extinguish: Disabled;

Normally Light: Communication fail; Blink: Communication normal.

RS232(Red)

| Normally Extinguish: RS232 disabled; Normally Light: Communication fail;

Blink: Communication normal.

CMM366A-WIFI Cloud Monitoring Communication Module User Manual

Internal lamp test/reset key:
Press it for 1s, all the LEDs are illuminated; press it for 10s, reset the module to default and all the
LEDs blink for 3 times.
NOTE: After reset the module, parameters need to be re-configured via PC software. Please operate cautiously.
WIFI ANTENNA INTERFACE
Connect WIFI antenna with module antenna, which is showing as below,

Fig.2 – WIFI Antenna Connection Diagram

RS485 INTERFACE
Connect RS485 port with genset control module RS485 port to achieve genset data information.
If communication fails, recommend adding a 120Ω terminal resistor. One end of shielding wire
connects with SCR, the other end hangs in the air.

Fig.4 – RS232 Connection Diagram
RS232 INTERFACE
Connect RS232 port with genset control module RS232 port to achieve genset data information.
LINK INTERFACE
Connect RS232 port with genset control module RS232 port to achieve genset data information

Fig.4 – RS232 Connection Diagram

LINK INTERFACE
Connect LINK port with genset control module LINK port to achieve genset data information.

Fig.5 – LINK Connection Diagram

USB HOST INTERFACE
Connect A-type USB port with genset control module USB port to achieve genset data information.

Fig.6 – USB HOST Connection Diagram
USB DEVICE INTERFACE
All the parameters can be configured and view CMM366A-WIFI ID &Login password by connecting USB port with USB disk of PC software.

Fig.7 – USB Connect PC Device

TERMINAL

Table 4 – Terminals Description

recommended.
3| Aux. Input 1| 1.0mm2| Active when connect to B-.
4| Aux. Input 2| 1.0mm2| Active when connect to B-.
5| **** Aux. Output| Normally Open| 1.0mm2| **** Normally open output 1A DC30V
6| Common| 1.0mm2
7| Normally Close| 1.0mm2
8| RS485 B(-)| 0.5mm2| Impedance-120Ω shielding wire is recommended, its single-end earthed.
9| RS485 A(+)| 0.5mm2
10| SCR| 0.5mm2
11| RS232 RX| 0.5mm2| **** RS232
12| RS232 TX| 0.5mm2
13| RS232 GND| 0.5mm2

PROGRAMMABLE PARAMETERS

CONTENTS AND SCOPES OF PARAMETERS

Table 5 – Parameter Content & Scope

WIFI
1| DHCP Enable| (0-1)| 1| 0: Disabled; 1: Enabled, autoobtain IP address.
2| IP Address| (0-255)| 192.168.0.101| All changes of Ethernet (like IP address, Subnet address) are active after module rebooting.
3| Subnet Mask| (0-255)| 255.255.255.0
4| Default Gateway| (0-255)| 192.168.0.2
5| DNS Address| (0-255)| 211.138.24.66
6| MAC Address| (0-255)| E.g. 00.08.DC.01.02.03
7| SSID| (0-65535)| 32 characters
8| Password| (0-65535)| 64 characters
Gateway
1| Site Name| (0-65535)| 20 Chinese characters, lettersor numbers
2| Server URL| (0-65535)| www.monitoryun.com| 40 characters
3| Server Port| (0-65535)| 91
4| Security Code| (0-65535)| 123456| 16 characters
GPS
1| Location Info| (0-1)| 0| 0: Disabled1: Manually Input
2| Longitude| ((-180)-180)°| 0.000000| GPS        location,         altitude information
3| Latitude| ((-90)-90)°| 0.000000
4| Altitude| ((-9999.9)-9999.9)m| 100.0
Input Port
Input 1
1| Setting| (0-9)| 0| Default: Not used
2| Type| (0-1)| 0| 0: Close to Activate 1: Open to ActivateSee: Tabl _ _e 6 – Digital Input _ _Ports Content
3| Delay| (0-20.0)| 0.0| Action delay
Input 2
1| Setting| (0-9)| 1| Default: Lamp test
2| Type| (0-1)| 0| 0: Close to Activate 1: Open to ActivateSee: Tabl _ _e 6 – Digital Input _ _Ports Content
3| Delay| (0-20.0)| 0.0| Action delay
Output
1| Setting| (0-14)| 0| Default: Not used

CMM366A-WIFI Cloud Monitoring Communication Module User Manual

NOTE: Configuration of monitoring genset controller model, communication port, communication baud rate, and communication ID need to be set on the platform, and monitoring module needs to reboot after setting. Table 6 – Digital Input Ports Content

is active.
3| Access Alarm Input| Access alarm is uploaded to server when input is active.
4| Fire Alarm Input| Fire alarm is uploaded to server when input is active.
5| Alarm Input| External alarm is uploaded to server when input is active.
6| Reserved|
7| Reserved
8| Reserved
9| Factory Test Mode| It is only used for factory hardware port test when active.

Table 7 – Relay Output Ports Content

withfixed output delay 20s.
9| Reserved
10| Reserved
11| Reserved
12| Reserved
13| Reserved
14| Reserved

PC CONFIGURATION INTERFACE
Connecting the USB port of CMM366A-WIFI communication module with PC USB port to configure the parameters.


Fig.8 – WIFI Configuration

Fig.9 – Gateway Configuration

Fig.10 – Module Monitoring Screen

SYSTEM DIAGRAM

One CMM366A-WIFI module connects with one genset monitor module. It can be connected via RS485 port, LINK port, RS232 port or USB port.

CASE DIMENSION AND INSTALLATION

2 ways for installation: 35mm guide rail in box or screw (M4) installation as below:


Fig. 12 – CMM366A-WIFI Case Dimension

Fig. 13 – CMM366A-WIFI Guide Rail Installation

TROUBLESHOOTING

**Table 8 – Troubleshooting

**

connection wirings.
Network indicator not light| Check Ethernet parameters are correct or not; Check Network socket indicator is light or not;Check cable is normal or not.
RS485 communication abnormal| Check connections;Check RS485 port is enabled or not;Check settings of genset ID and baud rate are correct or not. Check RS485’s connections of A and B is reverse connect or not.
RS232 communication abnormal| Check connections;Check RS232 port is enabled or not;Check settings of genset ID and baud rate are correct or not.
LINK communication abnormal| Check connections;Check LINK port is enabled or not;Check settings of genset ID and baud rate are correct or not.

PACKING LIST

Table 9 – Packing List

References

• 机组云监控
• smartgen.cn/
• smartgen.com.cn/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>