SmartGen DIN16A Digital Input Module User Manual

SmartGen DIN16A Digital Input Module User Manual

Introduction

All rights reserved. No part of this publication may be reproduced in any material form (including photocopying or storing in any medium by electronic means or other) without the written permission of the copyright holder.
Smart Gen Technology reserves the right to change the contents of this document without prior notice.

Table 1 Software Version

OVERVIEW

DIN16A digital input module is an expansion module which has 16 auxiliary digital input channels and the name of each channel can be defined by users. The input port status collected by DIN16A is transmitted to the HMC9000S controller for processing via CANBUS port.

TECHNICAL PARAMETER

Table 2 Technical Parameter.

PROTECTION

WARNING
Warnings are not shutdown alarms and do not affect the operation of the gen-set. When DIN16A module is enabled and detects the warning signal, the controller HMC9000S will initiate a warning alarm and the corresponding alarm information will be displayed on LCD.
Warning types are as follows:

Table 3 Warning Alarm List.

detects that the DIN16A auxiliary input 1-16 alarm signal and the action set as “Warning”, it will initiate a warning alarm and the corresponding alarm information will be displayed on LCD. (Each string of DIN16A input can be defined by users, such as input port 1 defined as “High Temp Warning”, when it is active,  corresponding alarm information will displayed on LCD.)

SHUTDOWN ALARM

When DIN16A module is enabled and detects the shutdown signal, the controller HMC9000S will initiate a shutdown alarm and the corresponding alarm information will be displayed on LCD.
Shutdown alarms are as follows:

Table 4 Stop Alarm List.

detects that the DIN16A auxiliary input 1-16 alarm signal and the action set as “Shutdown”, it will initiate a shutdown alarm and the corresponding alarm information will be displayed on LCD. (Each string of DIN16A input can be defined by users, such as input port 1 defined as “High Temp Shutdown”, when it is active,  corresponding alarm information will displayed on LCD.)
Note: The types of shutdown alarm of auxiliary input port are effective only when users configure them. Only emergency shutdown and overspeed shutdown work when the controller is in override mode.

PANEL CONFIGURATION

Users can set the parameters of DIN16A via HMC9000S module. Pressing and holding button for more than 3 seconds will enter the configuration menu, which allows users to set all DIN16A parameters, as follows:

Note: Pressing can exit setting directly during setting.

Table 5 Parameter Configuration List.

DEFINITION OF INPUT PORT

DEFINITION CONTENTS OF DIGITAL INPUT.

Table 6 Definition Contents List of Digital Input.

1：Open to activate
3| Effective Range| (0-3)| 0：From Safety on 1：From Crank 2：Always
3：Never
4| Effective   Action| (0-2)| 0：Warn 1：Shutdown 2：Indication
5| Input Delay| (0-20.0)s|
6| Display string| User-defined names of input port| Input port names can be edited via PC software only.

REAR PANEL

Panel drawing of DIN16A:
Fig.1 DIN16A Panel.

Table 7 Description of Terminal Connection.

| DC input B+| 2.5mm2| DC power supply positive input.

| SCR (CANBUS)| 0.5mm2| Connect CANBUS communication port to expansion CAN port of HMC9000S. Impedance-120Ω shielding wire with its one end grounded is recommended. There is 120Ω terminal resistance inside already; if needed, make terminal 5, 6 short circuits.
4.| CAN(H)(CANBUS)| 0.5mm2
5.| CAN(L) (CANBUS)| 0.5mm2
6.| 120Ω| 0.5mm2
7.| DIN1| 1.0mm2| Digital input
8.| DIN2| 1.0mm2| Digital input
9.| DIN3| 1.0mm2| Digital input
10.| DIN4| 1.0mm2| Digital input
11.| DIN5| 1.0mm2| Digital input
12.| DIN6| 1.0mm2| Digital input
13.| DIN7| 1.0mm2| Digital input
14.| DIN8| 1.0mm2| Digital input
15.| COM(B-)| 1.0mm2| Connect to B- is allowed.
16.| DIN9| 1.0mm2| Digital input
17.| DIN10| 1.0mm2| Digital input
18.| DIN 11| 1.0mm2| Digital input
19.| DIN 12| 1.0mm2| Digital input
20.| DIN 13| 1.0mm2| Digital input
21.| DIN 14| 1.0mm2| Digital input
22.| DIN 15| 1.0mm2| Digital input
23.| DIN 16| 1.0mm2| Digital input
24.| COM(B-)| 1.0mm2| Connect to B- is allowed.
DIP switch| SWITCH| | Address selection: It is module 1 when the switch 1 is connected to terminal 12 while module 2 when connect to ON terminal.

Baud rate selection: It is 250kbps when the switch 2 is connected to terminal 12 while 125kbps when connect to ON terminal.

LED Indicator| INPUT STATUS|  | When DIN1~DIN16 input are active, corresponding  DIN1 ~ DIN16 indicators are illuminate.

DIN16A TYPICAL APPLICATION

Fig.2 Typical Wiring Diagram.

INSTALLATION

Fig.3 Case Dimension and Panel Cutout.
Case dimension：

FAULT FINDING

connection wirings;
CANBUS communication failure| Check wiring.
Auxiliary input alarm| Check wiring.
Check if input polarities configuration is correct.

Customer Support

SmartGen Technology Co., Ltd
No.28 Jinsuo Road, Zhengzhou, Henan Province, China
Tel: +86-371-67988888/67981888/67992951
+86-371-67981000(overseas)
Fax: +86-371-67992952
Email: sales@smartgen.cn
Web: www.smartgen.com.cn
www.smartgen.cn

References

• 众智科技
• smartgen.cn/
• 众智科技

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>