CREALITY 205443 3D Printing Pen User Manual
- June 3, 2024
- Creality
Table of Contents
CREALITY 205443 3D Printing Pen
Dear Consumers,
Thank you for choosing our products. for the best experience, please read the
instructions before operating the printing pen. Our teams will always be ready
to render you the best services. please contact us via the phone number or
e-mail address provided at the end when you encounter any problem with the
Printer. For a better experience in using our product, you can also learn how
to use the printer in the following ways: Visit our official website
www.creality.com to find relevant soft
ware/hardware information, contact details, and operation and maintenance
instructions.
Warnings
- Please stay away from wet environments, do not put it in the bathroom or near the washing sink. don’t forget to turn down the power after usage.
- When charging, please use a standard 5V/2A USB charging adapter for charging.
- Six years above only, children should be companied by adults while
- The product uses a 1.75mm PCL filament. please use the authentic, filament. Otherwise, another non-authentic filament may cause nozzle: clogging.
- Please feed out the entire filament and turn off the power after usage.
- To fully test the product before shipping, there may be some filament left on the nozzle. It has no influence on usage.
- The manual version may change from time to time, please stay tuned with our official website.
Function introduction
- Separate feed-in/feed-out button
- Adjustable feed-in speeds (two modes)
- Automatic filament retraction and turn off when no usage
- Smooth use no matter on plate or dimensional
Product parameters
Introduction
Power button
Press and hold the power button for 5 seconds to turn on the device. at this
time, the indicator light flashes red, and the discharge port begins to warm
up. the indicator light turns green to indicate that the warm-up is completed
and the product enters the standby state. Click the power button and the red
indicator light flashes rapidly, please charge before use.
Feed-in button
after entering the standby state, put the filaments into the inlet/outlet,
press the button to enter the feeding state, press the button again to stop
the feeding.
Due to the differences between different machine models, the physical objects and the 1inal images can differ. The 1inal explanation rights shall be reserved by Shenzhen Creality 3D Technology Co., Ltd.
Speed-adjust button
the default mode after power-up is the low-speed mode. enter high-speed mode
with the click speed regulation key during the filament feed-out, and click
again to cycle switching.
Feed-out button
after entering the standby or working state, click the feed-out button to
return the filament.
Automatic feed-out
after five minutes no operation, the product will automatically return the
filaments. The green light flashes when returning the filaments. after
returning the filaments, it will automatically turn off the power.
Low-voltage reminder
when the battery power is low, the red indicator light will flash rapidly. if
it is in the feeding state at this time, the printing pen will automatically
return the material. after the return is completed, it will shut down. after
the low battery warning is turned off, it is recommended to use it after
charging.
Charging
Connect the built-in charging cable to the standard 5V /2A USB charging
adapter, and plug it into the Micro USB charging port. the long red light
means the charging is in progress, while the long blue light means the
charging is completed. during the charging process, the product is not
available.
Troubleshooting
The warranty ordinance
Hello! Thank you for choosing Creality 30 products. All the products are
produced under strict quality control and inspection. This warranty card
refers to the maintenance for customers when the product fails in normal use.
Warranty description
From the date of purchase, one year warranty can only be obtained in case of
failure under normal use. However, man-made damage (such as improper
disassembly of parts and handling, etc.) and natural damage (such as fire,
earthquake, flood, rat damage, etc.) don’t belong to the warranty. This
warranty card will not be reissued once lost, please keep it properly. If the
product fails after the warranty period, it will be provided with warranty
service and charged parts and handling fees when the company still has
accessories. Please keep this warranty card and invoice together for reference
during maintenance.
Warranty card
SHENZHEN CREALITY 3D TECHNOLOGY CO., L TD.
Add 18F, JinXiuHongDu Building, Meilong Blvd.,
Longhua Dist., Shenzhen, China 518131
Official Website: www.creality.com8usiness
Tel: +86 755-8523 4565 E-mail: Sales: info@creality.com
Support:cs@creality.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>