ROHL ROH8734 Authentic Luxury for Kitchen and Bath Installation Guide
- June 12, 2024
- ROHL
Table of Contents
ROHL ROH8734 Authentic Luxury for Kitchen and Bath
Product Information
The product being referred to in the user manual is a ROHL home installation guide. It is a comprehensive resource that provides information on installing and maintaining ROHL products. The manual includes instructions, specifications, and warranty details for the product. Product Usage Instructions: 1. Consult your local ROHL showroom: Before starting the installation process, it is recommended to consult your local ROHL showroom for additional information and specifications. They can provide you with expert advice and guidance specific to your product. 2. Visit www.rohlhome.com: To access complete warranty details and a list of showrooms, visit the official ROHL website at www.rohlhome.com. This website serves as a valuable resource for obtaining additional information and support related to the product. Please note that the provided text does not contain specific usage instructions for a particular product. If you have a specific ROHL product in mind, please provide more details, and I will be happy to assist you with detailed usage instructions.
Installation Instructions
INSTALLATION AND CARE & MAINTENANCE GUIDE
Note: Faucet must be installed a minimum of 2 inches above fixture rim.
- a – Preparation
- Flush out the pipework to remove any foreign matter.
- The hot supply should be on the left when viewed from the front of the fitting.
- b – Assembly
- Connect the eccentric shank (A) to side valve inlet.
- Assemble the round cap for eccentric (B), place caulking between wall and cap.
- Fix the body of sink mixer (C), placing the washer between the nut and the eccentric shank.
- Ensure all connections are firmly tightened.
- Introduce the spout (D) in the central hole of the body C and screw the nut (E).
- c – Before use
- Turn on the Hot and Cold supplies to the faucet.
- Maximum temperature for Hot water supply to the faucet is 145° F.
- Minimum recommended pressure is 15 psi
- Maximum recommended pressure is 75 psi.
- Check the installation carefully for leaks.
- If further building work is to be carried out in the vici of the faucet, it should be covered to prevent paint, adhesive, etc. from damaging the surface.
Care and use for finishes
Country Bath Products are all authentic finishes that have not been coated
with any product.
After each use, pat the fixture down to remove any excess water. This will
prevent any water spotting or mineral build-up. Use only soft liquid soap and
water to clean the surface. Use a soft brush to clean any gaps.
Avoid any products that have ammonia or alcohol like Windex,
409 or Fantastik. These products can damage the finish leaving black or white
spots. Never use an abrasive product like Softscrub, Comet, Ajax or Bon Ami.
For deep polishing we recommend Bruno’s Wax for all finishings.
Tuscan Brass is a living finish and has no warranty. It will lighten with use.
To extend the life of the finish, apply Bruno’s Wax by patting it on, letting
it dry and patting it off. Never rub or buff this finish.
WARNING: the use of cleaning products not recommended might irreparably harm
the surfaces of the faucets which in such case are not covered by our
warranty.
Limescale
The faucet is fitted with an aeration device in the Hot/Cold water outlet.
This may need occasional cleaning especially in hard water areas.
This is accomplished by unscrewing the outlet in a counter clockwise
direction, dismantling and leaving the inner screen mesh immersed over night
in vinegar or lemon juice.
Do not use chemical descaling liquids for this purpose.
ATTENTION
READ THESE INSTRUCTIONS BEFORE INSTALLATION AND USE OF ALL FAUCETS AND WALL
VALVES
INSTALLATION and WARRANTY INSTRUCTIONS TECHNICAL INFORMATION
All flexible hoses are designed and manufactured for use with water in exposed locations only. Do not expose to household cleaners, chlorine, cloride, hydrochloric acid or other corrosive chemicals.
-
All connections with threads M10x1 male must be hand tighten. Do not over tighten. Over-tightening may cause damage to the hose.
All faucets washers and o-rings are designed and manufactured for use with water. Do notexpose to household cleaners, chlorine, cloride, hydrochloric acid or other corrosive chemicals. -
Faucets are designed for use with the temperatures and pressures listed below:
- minimum cold water supply 50 °F
- maximum hot water supply 145 °F
- minimum pressure 15 psi
- maximum pressure 75 psi
- maximum fixing torque value = 10 Ibf.ft.
Please note: The recommended best pressure for best performance is between 40 psi and 60 psi. More pressure than 60 psi or less pressure than 40 psi may affect the diverting action in side spray faucets.
- Do not use any Rohl Country/ Nicolazzi faucet with sulphorous water.
- The minimum temperature for all faucets is 50 degrees F. Below 50 degrees F will void the warranty.
- When available, filter systems must be placed between hot and cold supply lines and the faucet. Improper use or non-use of filters may make diverting faucets with hand sprays perform poorly.
- Don’t modify faucet and their components
- Use only original spare parts if there are replacements to be ordered.
- Installation must be made by authorized plumbers or installers. Improper installation or diagnosis of problems is not covered by the warranty.
- Yearly maintenance of cleaning and flushing is recommended.
Operation and use of any faucet or wall valve that do not conform to these
technical instructions will void the warranty.
Consult your local ROHL showroom for additional information and
specifications. For complete warranty details and a list of showrooms, go to
www.rohlhome.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>